ISM0224S15

ISM02 Series DC-DC Converter XP Power 2 Watt • International medical safety approvals • Single & dual unregulated outputs • Compact SMD package • 4kV VAC reinforced isolation • 1 x MOPP at 300 VAC • 2 μA patient leakage current • Operating temperature -25 °C to +105 °C • Full load to 60°C convection • Tape & reel package available Dimensions: • 3 year warranty ISM02: 0.94 x 0.71 x 0.36” (24.0 x 18.1 x 9.3 mm) The ISM02 provides a compact cost effective SMD solution for healthcare applications providing 1 MOPP, 2 MOOP and IEC60601-1 compliance. Features include a high operating temperature, low leakage current, reinforced insulation and short circuit protection. Models & Ratings Input voltage 5V (4.5-5.5V) 12V (10.8-13.2V) 24V (21.6-26.4V) Output voltage Output current Max Min Input current(1) No load Full load Maximum capacitive load(2) Efficiency(6) Model number(3) 5V 400 mA 8.0 mA 605 mA 330 μF 72% ISM0205S05 12 V 165 mA 3.0 mA 600 mA 330 μF 72% ISM0205S12 15 V 133 mA 2.5 mA 605 mA 330 μF 72% ISM0205S15 ±12 V ±83 mA ±1.5 mA 555 mA ±100 μF 72% ISM0205D12 ±15 V ±66 mA ±1.0 mA 540 mA ±100 μF 73% ISM0205D15 5V 400 mA 8.0 mA 255 mA 330 μF 70% ISM0212S05 12 V 165 mA 3.0 mA 250 mA 330 μF 72% ISM0212S12 15 V 133 mA 2.5 mA 250 mA 330 μF 72% ISM0212S15 ±12 V ±83 mA ±1.5 mA 225 mA ±100 μF 74% ISM0212D12 ±15 V ±66 mA ±1.0 mA 220 mA ±100 μF 75% ISM0212D15 5V 400 mA 8.0 mA 125 mA 330 μF 68% ISM0224S05 12 V 165 mA 3.0 mA 125 mA 330 μF 68% ISM0224S12 15 V 133 mA 2.5 mA 125 mA 330 μF 68% ISM0224S15 ±12 V ±83 mA ±1.5 mA 110 mA ±100 μF 74% ISM0224D12 ±15 V ±66 mA ±1.0 mA 110 mA ±100 μF 75% ISM0224D15 90 mA 40 mA 30 mA Notes 1. Input currents measured at nominal input voltage. 2. Maximum capacitive load is per output. 3. For optional water washable version add suffix ‘-P’. 1 4. Add suffix ‘-TR’ for tape and reel. MOQ 200 pcs. 5. Standard tube quantity 10 pcs. 6. Measured at maximum load. www.xppower.com ISM02 Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Input Filter Minimum Typical 4.5 10.8 21.6 Internal Pi type filter Maximum 5.5 13.2 26.4 9 18 30 Input Surge Units VDC VDC for 1 s Notes & Conditions 5 V nominal 12 V nominal 24 V nominal 5 V nominal 12 V models 24 V models Output Characteristic Output Voltage Initial Set Accuracy Output Voltage Balance Minimum Load Line Regulation Load Regulation Minimum 5 Typical Maximum 30 ±4.0 ±1.0 ±1.5 10 Units VDC % % A % % ±5.0 % 5 % deviation Ripple & Noise 150 mV pk-pk Short Circuit Protection Maximum Capacitive Load Temperature Coefficient 0.5 s 0.02 %/ ˚C Maximum Units % VAC VDC μA Ω pF kHz W/in3 MHrs ±2.0 ±0.1 ±1.2 Cross Regulation Transient Response 3 Notes & Conditions See Models and Ratings table For dual output with balanced loads See Models and Ratings table From 20% to 100% load. 5V output version is 12% max On dual output models when one load is varied between 25% and 100% and other is fixed at 100% Recovery within 1% in less than 250 μs for a 25% load change. 20 MHz bandwidth. Measured using 0.47 μF ceramic capacitor. With auto recovery See Models and Ratings table General Characteristic Minimum Efficiency Isolation: Input to Output Leakage Current Isolation Resistance Isolation Capacitance Switching Frequency Power Density Mean Time Between Failure Typical 72 4000 6000 2 109 15 80 50 20 100 12.2 2 Notes & Conditions See Models and Ratings table 60 s, reinforced isolation at 300 VAC, 1 x MOPP/2 x MOOP 1s 240 VAC, 60 Hz At 500 VDC MIL-HDBK-217F, +25 °C GB Lead-Free Reflow Solder Process IPC/JEDEC J-STD-020D.1 Case Material Pin Material Weight Moisture Sensitivity Level Non conductive black plastic. UL94V-0 rated. Not suitable for water washing. Solder-coated phosphor bronze lb (g) 0.01 (3.75) IPC/JEDEC J-STD-020D.1 Level 2 Environmental Characteristic Maximum Units Notes & Conditions Operating Temperature Minimum -40 Typical +105 °C See derating curve Storage Temperature -50 +125 °C Case Temperature Humidity +105 °C 95 %RH Cooling Non-condensing Natural convection Safety Approvals Safety Agency Safety Standard Notes & Conditions CB Medical IEC60601-1 UL Medical ANSI AMMI ES60601-1 EN Medical EN60601-1 UL ITE UL/cUL60950-1, UL/cUL62368-1 CE Meets all applicable directives UKCA Meets all applicable legislation www.xppower.com 2 ISM02 Series DC-DC Converter XP Power EMC: Emissions Phenomenon Standard Test Level Conducted EN55011 Class A Notes & Conditions See Application Notes EMC: Immunity Test Level Criteria ESD Phenomenon EN61000-4-2 Standard ±15 kV air discharge, ±8 kV contact A Radiated EFT/Burst EN61000-4-3 EN61000-4-4 10 V/m ±2 kV A A Surge EN61000-4-5 ±1 kV A Conducted EN61000-4-6 6kV rms A Magnetic Fields EN61000-4-8 30 A/m A Notes & Conditions Mechanical Details Connecting Pin Pattern 0.94 (24.0) 0.70 (17.8) 7 8 0.77 (19.5) 1 0.54 (13.7) 10 9 0.65 (16.6) 16 0.71 (18.1) 0.10 (2.5) 0.54 (13.7) 0.60 (15.2) 0.12 (3.1) 0.04 (1.0) 0.06 (1.6) 0.10 (2.5) 0.35 (9.0) Pin Connections S 0.36±0.02 (9.25±0.5) SEATING PLANE 0~ 4 0.01 (0.25) 0.11 (2.9) 0.15 S Pin 1 7 8 9 10 16 Single -Vin No Connection No Connection +Vout -Vout +Vin Dual -Vin No Connection Common +Vout -Vout +Vin Application Notes Derating Curve EMC Circuit for Class A 100 16 Output Power (%) Convection 400 LFM forced air 9 C1 ISM02 10 1 0 -40 -25 60 75 C1 2.2µF/150V 105 Ambient Temperature (°C) L 88μH Notes 1. All dimensions are in inches (mm) 2. Weight: 0.01 lbs (3.75 g) approx. 3 3. Tolerance: X.XX±0.01 (X.X±0.25) X.XXX±0.005 (X.XX±0.13) 4. Pin Tolerance: ±0.002 (±0.05) www.xppower.com 01 Dec 2021