ITV1205SA

ITV Series DC-DC Converter XP Power 1 Watts xxx Series • Single & dual output, unregulated • -40 °C to +105 °C operation • SIP7 package • Full load at 95 °C ambient • 3000 VDC isolation, functional • Class B radiated emissions • MTBF >3.5 MHrs • 3 year warranty The ITV series of unregulated DC-DC modules provides an exceptional high operating temperature range while remaining cost effective. Features include short circuit protection and a robust encapsulated package. Dimensions: ITV: 0.76 x 0.24 x 0.39” (19.5 x 6.0 x 10.0 mm) Models & Ratings Input Voltage 5V 12 V 24 V Output Voltage Output Current Input Current(1) No Load Full Load Efficiency(3) Model Number 5V 200 mA 30 mA 253 mA 220 μF 80% ITV0505SA 12 V 83.3 mA 30 mA 253 mA 100 μF 80% ITV0512SA 15 V 66.7 mA 30 mA 253 mA 100 μF 80% ITV0515SA ±5 V ±100 mA 30 mA 253 mA ±100 μF 80% ITV0505S ±12 V ±41.6 mA 30 mA 250 mA ±47 μF 81% ITV0512S ±15 V ±33.3 mA 30 mA 250 mA ±47 μF 81% ITV0515S 5V 200 mA 15 mA 106 mA 220 μF 80% ITV1205SA 12 V 83.3 mA 15 mA 106 mA 100 μF 80% ITV1212SA 15 V 66.7 mA 15 mA 104 mA 100 μF 81% ITV1215SA ±5 V ±100 mA 15 mA 106 mA ±100 μF 80% ITV1205S ±12 V ±41.6 mA 15 mA 106 mA ±47 μF 80% ITV1212S ±15 V ±33.3 mA 15 mA 104 mA ±47 μF 81% ITV1215S 5V 200 mA 7 mA 53 mA 220 μF 80% ITV2405SA 12 V 83.3 mA 7 mA 53 mA 100 μF 80% ITV2412SA 15 V 66.7 mA 7 mA 53 mA 100 μF 80% ITV2415SA ±5 V ±100 mA 7 mA 53 mA ±100 μF 80% ITV2405S ±12 V ±41.6 mA 7 mA 53 mA ±47 μF 80% ITV2412S ±15 V ±33.3 mA 7 mA 53 mA ±47 μF 80% ITV2415S Notes 1. Input currents measured at nominal input voltage. 2. Maximum capacitive load is per output. 3. Measured at nominal input voltage and full load. 1 Maximum Capacitive Load(2) www.xppower.com ITV Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Input Filter Minimum Maximum Units Notes & Conditions 4.5 Typical 5.5 VDC 5 V nominal 10.8 13.2 VDC 12 V nominal 21.6 26.4 VDC 24 V nominal Capacitor Input Reflected Ripple Input Surge 15 mA pk-pk 9 VDC for 1000 ms Through 12 μH inductor and 47 μF capacitor 5 V models 18 VDC for 1000 ms 12 V models 30 VDC for 1000 ms 24 V models Maximum Units Notes & Conditions 15 VDC See Models and Ratings table ±5 % At 70% load % Minimum load required to meet specification. Operation at no load will not cause damage. Output Characteristic Minimum Output Voltage 5 Typical Initial Set Accuracy Minimum Load 10 Line Regulation ±1.2 %/1%Vin Load Regulation +5, -2.5 % From 10% to full load from 70% load point On dual output models when one load is varied between 25% and 100% and other is fixed at 100% Cross Regulation ±5 % Ripple & Noise 60 mV pk-pk Short Circuit Protection 20 MHz bandwidth. Measured using 0.1 μF ceramic capacitor Continuous, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ ˚C Maximum Units General Characteristic Minimum Efficiency Isolation: Input to Output Typical 80 % 3000 Switching Frequency 40/50 Isolation Resistance 109 VAC 50/70 kHz 60s qualification. Functional insulation. 5 V/12-24 V input Ω 14 Power Density Mean Time Between Failure 100 50 Isolation Capacitance See Models and Ratings table VDC Working Voltage Notes & Conditions 3.6 pF Win3 MHrs MIL-HDBK-217F, +25 °C GB Pin Type Solder coated phospher bronze C5191R-H Case Material Non conductive black plastic UL94V-0 rated Potting Material Epoxy UL94V-0 rated Solder Profile 260°C maximum Weight 1.5mm from case, up to 10s max 0.0053 (2.4) lb (g) Environmental Characteristic Maximum Units Operating Temperature Minimum -40 Typical +105 °C Storage Temperature -55 +125 °C Case Temperature Humidity +115 °C 95 %RH Cooling Notes & Conditions Derate from 100% load at +95 °C to 90% at +105 °C Non-condensing Natural convection Safety Approvals Safety Agency Safety Standard Notes & Conditions CE Meets all applicable directives UKCA Meets all applicable legislation www.xppower.com ITV Series DC-DC Converter XP Power EMC: Emissions Phenomenon Standard Test Level Notes & Conditions Conducted EN55022 Class B See Application Note Radiated EN55022 Class B EMC: Immunity Phenomenon Standard Test Level Criteria ESD Immunity EN61000-4-2 3 A Notes & Conditions Radiated Immunity EN61000-4-3 10 Vrms A EFT/Burst EN61000-4-4 3 A External input capacitor required 330 μF/100 V Surges EN61000-4-5 1 A External input capacitor required 330 μF/100 V Conducted Immunity EN61000-4-6 3 V rms A Magnetic Fields EN61000-4-8 1 A/m A Mechanical Details 0.76 (19.5) Pin Connections 0.24 (6.00) Pin 1 2 4 5 6 7 Printed Face 0.37 (9.50) 0.39 (10.0) 0.02 (0.50) 0.12 (3.05) 0.10 (2.54) 0.60 (15.24) 0.05 (1.25) Dual +Vin -Vin No Pin -Vout Common +Vout Notes 1. All dimensions are in inches (mm) 2. Weight: 0.0053lbs (2.4 g) approx. 3. Pin diameter: 0.02±0.002 (0.5±0.05) 4. Pin pitch tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) 0.02 (0.50) 0.24 (6.00) Single +Vin -Vin No Pin -Vout No Pin +Vout 0.01 (0.25) 0.02 (0.50) Application Note EMI Filter + Vout + Vin 6.8 µH Load ITV 4.7 µF/50 V -Vin -Vout 1206 Chip Capacitor, placed as close as possible to the input pins 3 www.xppower.com 23 Sept 2021