ITX4815S

ITX Series DC-DC Converter XP Power 6 Watt xxx Series • 2:1 Input Range • SIP-8 Plastic Case • Operating Temperature -40 °C to +90 °C • Single and Dual Outputs • 1500 VDC Isolation, 3000 VDC Option • Remote Control Option • 3 Year Warranty Dimensions: ITX: 0.86 x 0.44 x 0.36” (21.85 x 11.1 x 9.2 mm) Models & Ratings Input Voltage 4.5-9 V 9-18 V 18-36 V 36-75 V Output Voltage 3.3 V 5.0 V 9.0 V 12.0 V 15.0 V 24.0 V ±5.0 V ±12.0 V ±15.0 V 3.3 V 5.0 V 9.0 V 12.0 V 15.0 V 24.0 V ±5.0 V ±12.0 V ±15.0 V 3.3 V 5.0 V 9.0 V 12.0 V 15.0 V 24.0 V ±5.0 V ±12.0 V ±15.0 V 3.3 V 5.0 V 9.0 V 12.0 V 15.0 V 24.0 V ±5.0 V ±12.0 V ±15.0 V Output Current 1300 1200 666 500 400 250 ±600 ±250 ±200 1300 1200 666 500 400 250 ±600 ±250 ±200 1300 1200 666 500 400 250 ±600 ±250 ±200 1300 1200 666 500 400 250 ±600 ±250 ±200 mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Input Current(3) No Load Full Load 105 mA 105 mA 105 mA 105 mA 105 mA 105 mA 105 mA 105 mA 105 mA 55 mA 55 mA 55 mA 55 mA 55 mA 55 mA 55 mA 55 mA 55 mA 30 mA 30 mA 30 mA 30 mA 30 mA 30 mA 30 mA 30 mA 30 mA 15 mA 15 mA 15 mA 15 mA 15 mA 15 mA 15 mA 15 mA 15 mA 1114 1481 1445 1428 1428 1428 1481 1428 1428 458 602 595 588 588 595 609 595 595 229 301 294 294 290 294 304 297 297 114 152 148 147 145 148 152 147 147 mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Notes 1. For optional 3000 VDC isolation add suffix ‘-H’ to end of part number e.g. ITX1205SA-H. 2. For optional remote control add suffix ‘-R’ to end of part number e.g. ITX2412S-HR. 3. Input currents measured at nominal input voltage. 1 www.xppower.com Maximum Capacitive Load 6600 3300 2000 1600 1400 680 ±2000 ±900 ±660 6600 3300 2000 1600 1400 680 ±2000 ±900 ±660 6600 3300 2000 1600 1400 680 ±2000 ±900 ±660 6600 3300 2000 1600 1400 680 ±2000 ±900 ±660 μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF Efficiency 77% 81% 83% 84% 84% 84% 81% 84% 84% 78% 83% 84% 85% 85% 84% 82% 84% 84% 78% 83% 85% 85% 86% 85% 82% 84% 84% 78% 82% 84% 85% 86% 84% 82% 85% 85% Model Number(1,2) ITX0503SA ITX0505SA ITX0509SA ITX0512SA ITX0515SA ITX0524SA ITX0505S ITX0512S ITX0515S ITX1203SA ITX1205SA ITX1209SA ITX1212SA ITX1215SA ITX1224SA ITX1205S ITX1212S ITX1215S ITX2403SA ITX2405SA ITX2409SA ITX2412SA ITX2415SA ITX2424SA ITX2405S ITX2412S ITX2415S ITX4803SA ITX4805SA ITX4809SA ITX4812SA ITX4815SA ITX4824SA ITX4805S ITX4812S ITX4815S ITX Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Minimum Maximum Units Notes & Conditions 4.5 Typical 9 VDC 5 V nominal 9 18 VDC 12 V nominal 18 36 VDC 24 V nominal 36 75 VDC 48 V nominal 30 15 25 mA pk-pk VDC for 100 ms VDC for 100 ms Through 12 μH inductor and 47 μF capacitor 5 V models 12 V models Input Current See Models and Ratings table Input Reflected Ripple Input Surge 50 VDC for 100 ms 24 V models 100 VDC for 100 ms 48 V models Maximum Units Output Voltage Balance ±2 % Initial Set Accuracy ±1 % ±0.2 % Load Regulation ±1 % From 0-100% Cross Regulation ±5.0 % Dual output models when one load is varied between 25% and 100% and the other is fixed at 100% load 75 mV pk-pk Input Filter Capacitor Output Characteristic Minimum Typical Output Voltage Minimum Load See Models and Ratings table 0 Start Up Delay Dual output models A Line Regulation 30 Ripple and Noise Transient Response ms 3 % deviation Short Circuit Protection 20 MHz bandwidth, measured using 0.1 μF capacitor Recovery to within 1% in 500 μs for a 25% load change (5% max. deviation for 3.3 & 5 V models) Continuous, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient Remote On/Off Notes & Conditions 0.02 %/˚C Optional by adding suffix -R to model number. Output off: 2-4 mA via 1KΩ resistor into pin 3 with respect to -Vin. Output on: Open or high impedance. General Characteristic Minimum Typical Maximum Units Notes & Conditions 1500 VDC For optional high isolation versions, 3000 VDC input to output add suffix -H to model number 1.5 MHz Variable Efficiency See Models and Ratings table Isolation: Input to Output Switching Frequency 0.1 Isolation Resistance 109 Ω Isolation Capacitance 50 Power Density 44 Mean Time Between Failure 770 Weight 0.011 (4.8) pF Win3 Input to output kHrs MIL-HDBK-217F, +25 °C GB lb (g) Environmental Characteristic Minimum Operating Temperature -40 Storage Temperature -55 Case Temperature Operating Humidity Typical Maximum Units +90 °C +125 °C +105 °C 95 % RH Cooling Notes & Conditions Derate from 100% load at +65 °C to 20% load at 90 °C, for all models except 5 V and ±5 V models: derate from 100% load at 55 °C to 20% load at 90 °C) Non-condensing Natural convection www.xppower.com 2 ITX Series DC-DC Converter XP Power EMC: Emissions Phenomenon Standard Test Level Notes & Conditions Conducted EN55022 Class A See Application Note Radiated EN55022 Class A Phenomenon Standard Test Level Criteria ESD Immunity EN61000-4-2 3 B Radiated Immunity EN61000-4-3 20 V/m A EFT/Burst EN61000-4-4 3 B External input capacitor required, 330 μF/100 V Surge EN61000-4-5 2 B External input capacitor required, 330 μF/100 V Conducted Immunity EN61000-4-6 3 V rms A Magnetic Fields EN61000-4-8 1 A/m A EMC: Immunity Notes & Conditions Safety Approvals Safety Agency Safety Standard Notes & Conditions UL UL60950-1, UL62368-1 CSA CAN/CSA C22.2 No.60950-1 CE Meets all applicable directives UKCA Meets all applicable legislation Mechanical Details 0.86 (21.85) 0.36 (9.2) Printed Face 0.42 (10.6) 0.02 (0.5) 0.44 (11.1) 1 2 3 5 6 7 8 PIN CONNECTIONS Pin 1 2 3 5 6 7 8 0.11 (3.0) 0.10 (2.54) 0.70 (17.78) 0.02 (0.5) 0.36 (9.20) Single -R -Vin +Vin Remote On/Off N.C. +Vout - Vout N.C. 1. All dimensions are in inches (mm) 2. Weight: 0.011 lbs (4.8 g) typical. 3. Pin diameter: 0.02 ±0.002 (0.5 ±0.005) 4. Pin pitch and length tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) 0.02 (0.5) Application Note EMI Filter C4 Input filter components (C1,C2,C3,C4,C5, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. ITX05 ITX12 ITX24 ITX48 C1 220μF/100V - C2 & C3* 22 μF/25 V 10 μF/50 V 10 μF/50 V 2.2 μF/100 V L 10 μH 10 μH 10 μH 15 μH + Vout + Vin L C4 & C5* 220 pF/3 kV 220 pF/3 kV 220 pF/3 kV 220 pF/3 kV * C2, C3, C4 & C5 are multilayer ceramic capacitors. 3 Dual -R -Vin +Vin Remote On/Off N.C. +Vout Common -Vout Notes 0.01 (0.25) 0.13 (3.20) PIN CONNECTIONS Single Dual -Vin -Vin +Vin +Vin N.P. N.C. N.P. N.C. +Vout +Vout - Vout Common N.C. -Vout Pin 1 2 3 5 6 7 8 C1 C2 Load ITX C3 -Vin -Vout C5 www.xppower.com 23 Sept 2021