JCE0324D15-H

JCE03 Series DC-DC Converter XP Power 3 Watt xxx Series • 2:1 Input Range • DIP24 Plastic Case • Operating Temperature -40 °C to +100 °C • Single & Dual Outputs • 1500 VDC Isolation, 3000 VDC Option • Fully Regulated Output • No Minimum Load Required • 3 Year Warranty Dimensions: JCE: 1.25 x 0.80 x 0.40” (31.75 x 20.32 x 10.16 mm) Models & Ratings Input Voltage 9-18 V 18-36 V 36-75 V Output Voltage Output Current Input Current(1) No Load Full Load Efficiency Model Number(3) 3.3 V 900 mA 7 mA 339 mA 470 μF 74% JCE0312S3V3 5.0 V 600 mA 7 mA 325 mA 470 μF 78% JCE0312S05 12.0 V 250 mA 10 mA 313 mA 100 μF 81% JCE0312S12 15.0 V 200 mA 10 mA 313 mA 100 μF 81% JCE0312S15 24.0 V 125 mA 20 mA 316 mA 47 μF 80% JCE0312S24 ±3.3 V ±450 mA 10 mA 339 mA ±220 μF 74% JCE0312D03 ±5.0 V ±300 mA 10 mA 325 mA ±220 μF 78% JCE0312D05 ±12.0 V ±125 mA 15 mA 313 mA ±100 μF 81% JCE0312D12 ±15.0 V ±100 mA 20 mA 313 mA ±100 μF 81% JCE0312D15 ±24.0 V ±63 mA 35 mA 319 mA ±47 μF 80% JCE0312D24 3.3 V 900 mA 7 mA 172 mA 470 μF 73% JCE0324S3V3 5.0 V 600 mA 7 mA 164 mA 470 μF 77% JCE0324S05 12.0 V 250 mA 7 mA 156 mA 100 μF 81% JCE0324S12 15.0 V 200 mA 7 mA 156 mA 100 μF 81% JCE0324S15 24.0 V 125 mA 10 mA 156 mA 47 μF 81% JCE0324S24 ±3.3 V ±450 mA 7 mA 167 mA ±220 μF 75% JCE0324D03 ±5.0 V ±300 mA 7 mA 160 mA ±220 μF 79% JCE0324D05 ±12.0 V ±125 mA 10 mA 156 mA ±100 μF 81% JCE0324D12 ±15.0 V ±100 mA 15 mA 156 mA ±100 μF 81% JCE0324D15 ±24.0 V ±63 mA 20 mA 158 mA ±47 μF 81% JCE0324D24 3.3 V 900 mA 7 mA 84 mA 470 μF 75% JCE0348S3V3 5.0 V 600 mA 7 mA 80 mA 470 μF 79% JCE0348S05 12.0 V 250 mA 7 mA 78 mA 100 μF 81% JCE0348S12 15.0 V 200 mA 7 mA 78 mA 100 μF 81% JCE0348S15 24.0 V 125 mA 7 mA 78 mA 47 μF 81% JCE0348S24 ±3.3 V ±450 mA 7 mA 81 mA ±220 μF 77% JCE0348D03 ±5.0 V ±300 mA 7 mA 78 mA ±220 μF 81% JCE0348D05 ±12.0 V ±125 mA 7 mA 78 mA ±100 μF 81% JCE0348D12 ±15.0 V ±100 mA 7 mA 78 mA ±100 μF 81% JCE0348D15 ±24.0 V ±63 mA 15 mA 81 mA ±47 μF 79% JCE0348D24 Notes 1. Input currents measured at nominal input voltage. 2. Maximum capacitive load is per output. 3. For optional 3000 VDC isolation add suffix ‘-H’ to model number. 1 Maximum Capacitive Load(2) www.xppower.com JCE03 Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Input Filter Minimum Maximum Units Notes & Conditions 9 Typical 18 VDC 12 V nominal 18 36 VDC 24 V nominal 36 75 VDC 48 V nominal Pi type Input Reflected Ripple 20 mA pk-pk 25 VDC for 100 ms 12 V models 50 VDC for 100 ms 24 V models 100 VDC for 100 ms 48 V models Maximum Units ±2 % Line Regulation ±0.5 % Load Regulation ±1.2 % Cross Regulation ±5 % Transient Response 3 % deviation Ripple & Noise 80 mV pk-pk Input Surge Through 12 μH inductor and 47 μF capacitor Output Characteristic Minimum Typical Output Voltage See Models and Ratings table Initial Set Accuracy Minimum Load Notes & Conditions 0 A No minimum load required On dual output models when one load is varied between 25% and 100% and other is fixed at 100% Short Circuit Protection Recovery within 2% in less than 2 ms for a 25% load change. S3V3 versions: 5% max 20 MHz bandwidth. Measured using 1 μF ceramic capacitor D24 versions: 100 mV pk-pk Continuous, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ ˚C Maximum Units General Characteristic Minimum Efficiency Typical 81 % 1500 Isolation: Input to Output Switching Frequency Isolation Resistance kHz 1000 pF W/in3 7.5 800 Weight 3000 VDC option, add ‘-H’ to model number Ω Power Density Mean Time Between Failure See Models and Ratings table VDC 330 109 Isolation Capacitance Notes & Conditions kHrs 0.03 (13.0) MIL-HDBK-217F, +25 °C GB lb (g) Environmental Characteristic Maximum Units Operating Temperature -40 +100 °C Storage Temperature -55 +125 °C Case Temperature Humidity Minimum Typical +100 °C 95 %RH Cooling Notes & Conditions Derate from 100% load at +85 °C to no load at +100 °C Non-condensing Natural convection www.xppower.com 2 JCE03 Series DC-DC Converter XP Power EMC: Emissions Phenomenon Standard Test Level Conducted EN55032 Class A Radiated EN55032 Class A Notes & Conditions Class B with external components, see application notes EMC: Immunity Phenomenon Standard Test Level Criteria ESD Immunity EN61000-4-2 3 A Notes & Conditions Radiated Immunity EN61000-4-3 20 Vrms A EFT/Burst EN61000-4-4 3 A External input capacitor required 330 μF/100 V Surges EN61000-4-5 Installation class 2 A External input capacitor required 330 μF/100 V Conducted Immunity EN61000-4-6 3 V rms A Magnetic Fields EN61000-4-8 1 A/m A Safety Approvals Safety Agency Safety Standard Notes & Conditions UL UL62368-1 & CAN/CSA C22.2 No. 62368-1-14 CE Meets all applicable directives UKCA Meets all applicable legislation Information Technology Mechanical Details 1.25 (31.75) Printed Face 0.40 (10.16) 0.80 (20.32) 0.12 (3.00) Pin Connections Pin 2 3 9 11 14 16 22 23 0.90 (22.86) 0.02 (0.50) 11 9 2 3 0.60 (15.24) Bottom View 23 22 14 16 0.02 (0.50) 0.20 (5.08) Single -Vin -Vin N.P. N.C. +Vout -Vout +Vin +Vin Dual -Vin -Vin Common -Vout +Vout Common +Vin +Vin Application Notes Class B Conducted Emissions Filter +Vout 4.7 µH +Vin + 4.7 µF(K) 50 V - DC/DC Converter 4.7 µF(K) 50 V Load -Vin -Vout 300 pF (M), 2kV Notes 1. All dimensions are in inches (mm) 2. Weight: 0.03 lbs (13.0 g) approx. 3. Pin diameter: 0.02±0.002 (0.5±0.05) 3 4. Pin pitch tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) www.xppower.com 29 Sept 2021