JCE0612S24

DC-DC 6 Watts xppower.com JCE Series • 2:1 Input Range • DIP-24 Plastic Case • Operating Temperature -40 °C to +100 °C • Single & Dual Outputs • Optional Metal Case • 1500 VDC Isolation, 3000 VDC Option • 3 Year Warranty Specification Input General Input Voltage Range • 12 V (9-18 VDC) 24 V (18-36 VDC) 48 V (36-75 VDC) Input Current • See table Input Filter • Pi network Input Reflected Ripple • 20 mA pk-pk through 12 μH inductor and 4.7 μF capacitor Input Surge • 12 V models 25 VDC for 100 ms 24 V models 50 VDC for 100 ms 48 V models 100 VDC for 100 ms Under Voltage Lockout • 12 V models on >8.5 V, off 16.5 V, off 34.5 V, off 800 KHrs to MIL-STD-217F at 25 °C, GB • • • • • -40 °C to +100 °C (see derating curve) +100 °C max -55 °C to +125 °C Convection-cooled Up to 95% RH, non-condensing • • • • • • • EN55032 Class A conducted EN61000-4-2, level 3, Perf Criteria B EN61000-4-3, 10 V/m, Perf Criteria A EN61000-4-4, level 3 Perf Criteria A EN61000-4-5, level 2, Perf Criteria A* EN61000-4-6, 10 Vrms, Perf Criteria A EN61000-4-8, 1 A/m, Perf Criteria A Environmental Output Output Voltage Output Voltage Balance Initial Set Accuracy Minimum Load Line Regulation Load Regulation • • • • • • Cross Regulation • Start Up Delay Ripple & Noise • • Transient Response • Overload Protection • Short Circuit Protection • Maximum Capacitive Load Temperature Coefficient Efficiency Isolation Voltage • See table ±2% max, dual output models ±2% max No minimum load required ±0.5% max ±1.2% max, for single output and ±5% max for dual output from 10-100% ±5% max, on dual output models (see note 1) 20 ms typical 80 mV pk-pk (100 mV for D24 models), 20 MHz bandwidth. See note 2 3% max deviation, recovery to within 1% in 300 μs for a 25% load change (4% max. deviation for S3V3 models) 135% - 185% of full load Trip and restart (hiccup mode), auto recovery See table • 0.02%/°C max Operating Temperature Case Temperature Storage Temperature Cooling Operating Humidity EMC Emissions ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Magnetic Field Safety Safety Approvals • UL62368-1, CAN/CSA C22.2 No. 62368-1 and 62368-1, CE (Meets all applicable directives), UKCA (Meets all applicable legislation) * External input capacitor required, 220μF/100V (See note 7) Output Voltage Input Voltage 3.3 V 5.0 V 12.0 V 15.0 V 24.0 V ±3.3 V ±5.0 V ±12.0 V ±15.0 V ±24.0 V 3.3 V 5.0 V 12.0 V 15.0 V 24.0 V ±3.3 V ±5.0 V ±12.0 V ±15.0 V ±24.0 V 3.3 V 5.0 V 12.0 V 15.0 V 24.0 V ±3.3 V ±5.0 V ±12.0 V ±15.0 V ±24.0 V 9-18 VDC 18-36 VDC 36-75 VDC Input Current(1) Output Current 1400 1200 500 400 250 ±909 ±600 ±250 ±200 ±125 1400 1200 500 400 250 ±909 ±600 ±250 ±200 ±125 1400 1200 500 400 250 ±909 ±600 ±250 ±200 ±125 No Load mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Maximum Capacitive Load(6) Full Load 7 mA 7 mA 10 mA 10 mA 20 mA 10 mA 10 mA 15 mA 20 mA 35 mA 7 mA 7 mA 7 mA 7 mA 10 mA 7 mA 7 mA 10 mA 15 mA 20 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 7 mA 15 mA 513 633 602 595 610 658 625 602 595 617 260 316 301 301 305 329 312 301 298 305 128 154 151 151 151 162 154 151 151 158 mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA 470 470 100 100 47 ±220 ±220 ±100 ±100 ±47 470 470 100 100 47 ±220 ±220 ±100 ±100 ±47 470 470 100 100 47 ±220 ±220 ±100 ±100 ±47 Efficiency Model Number(4,5) 75% 79% 83% 84% 82% 76% 80% 83% 84% 81% 74% 79% 83% 83% 82% 76% 80% 83% 84% 82% 76% 82% 84% 84% 84% 78% 82% 84% 84% 80% JCE0612S3V3 JCE0612S05 JCE0612S12 JCE0612S15 JCE0612S24 JCE0612D03 JCE0612D05 JCE0612D12 JCE0612D15 JCE0612D24 JCE0624S3V3 JCE0624S05 JCE0624S12 JCE0624S15 JCE0624S24 JCE0624D03 JCE0624D05 JCE0624D12 JCE0624D15 JCE0624D24 JCE0648S3V3 JCE0648S05 JCE0648S12 JCE0648S15 JCE0648S24 JCE0648D03 JCE0648D05 JCE0648D12 JCE0648D15 JCE0648D24 μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF μF Notes 1. When one output is set at 100% load and the other varies between 25% & 100% load. 2. Measured with 20 MHz bandwidth and 1 μF ceramic capacitor across output rails. 3. Input current specified at nominal 12 V, 24 V or 48 V input. 4. For optional 3000 VDC isolation add suffix -H to part number e.g. JCE0624S12-H 5. For optional metal case version add suffix -M to part number e.g. JCE0612S24-M 6. Maximum capacitive load is per output 7. For surge immunity, external input capacitor required, 220 μF/100 V. 24 V & 48 V input models are Perf Criteria A, 12 V input models are Perf Criteria B. Mechanical Details ( ) ( Optional Metal Case Plastic Case 1.25 (31.75) ) Printed Face DIA 0.02 (0.50) 1.25 (31.75) 0.40 (10.40) 0.80 (20.32) 0.90 (22.86) 2 0.80 (20.32) 0.12 (3.05) 0.02 (0.50) 9 2 3 11 0.60 (15.24) Bottom View 23 22 0.02 (0.50) 16 14 0.20 (5.08) Pin Single Dual 2 3 9 11 14 16 22 23 -Vin -Vin No Pin N.C. +Vout -Vout +Vin +Vin -Vin -Vin Common -Vout +Vout Common +Vin +Vin 9 22 16 0.10 (2.54) Printed Face 11 0.60 (15.24) Bottom View 23 0.90 (22.86) 3 14 0.20 (5.08) 0.40 (10.40) 0.12 (3.05) Min. Notes 1. All dimensions are in inches (mm) 2. Weight: 0.03 lbs (13 g) for plastic case, 0.04 lbs (16.5 g) for metal case 3. Pin diameter: 0.02 ±0.002 (0.5 ±0.005) 4. Pin pitch and length tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) 6. Package: 24 pin DIL black plastic (UL94V-0) or optional nickel-coated copper. Application Notes 100 80 Load (%) Derating Curve 60 40 20 0 -40 -20 0 10 20 30 40 50 60 Ambient Temperature (ºC) 70 80 90 100 29 Sept 2021 DC-DC JCE06 Models and Ratings