JCM3048S15

JCM30 Series DC-DC Converter XP Power 30 Watts xxx Series • Single and Dual Outputs • 2:1 Input Range • 1” x 1” Footprint • -40 °C to +100 °C Operation • Full Load at 55 °C Ambient • 1600 VDC Isolation • Output Trim ±10% • Remote On/Off • MTBF 370 kHrs Dimensions: • 3 Year Warranty JCM30: 1.0 x 1.0 x 0.41” (25.4 x 25.0 x 10.4 mm) Models & Ratings Input Voltage Output Voltage 9-18 V Input Current(1) Output Current No Load Full Load OVP setting Efficiency Max. capacitive load Model Number(3) JCM3012S3V3 3.3 V 7.0 A 10 mA 2215 mA 3.9 V 87% 10000 μF 5.0 V 6.0 A 10 mA 2810 mA 6.2 V 89% 7200 μF JCM3012S05 12.0 V 2.5 A 12 mA 2810 mA 15.0 V 89% 1200 μF JCM3012S12 15.0 V 2.0 A 12 mA 2810 mA 18.0 V 89% 1000 μF JCM3012S15 ±12.0 V ±1.25 A 12 mA 2810 mA ±15.0 V 89% ±750 μF JCM3012D12 ±15 V ±1.0 A 14 mA 2780 mA ±18.0 V 90% ±500 μF JCM3012D15 3.3 V 7.0 A 10 mA 1105 mA 3.9 V 87% 10000 μF 5V 6.0 A 10 mA 1390 mA 6.2 V 90% 7200 μF JCM3024S05 12 V 2.5 A 10 mA 1375 mA 15.0 V 91% 1200 μF JCM3024S12 15 V 2.0 A 10 mA 1375 mA 18.0 V 91% 1000 μF JCM3024S15 ±12 V ±1.25 A 10 mA 1375 mA ±15.0 V 91% ±750 μF JCM3024D12 ±15 V ±1.0 A 10 mA 1375 mA ±18.0 V 92% ±500 μF JCM3024D15 3.3 V 7.0 A 8 mA 545 mA 3.9 V 88% 10000 μF 5V 6.0 A 8 mA 695 mA 6.2 V 90% 7200 μF JCM3048S05 12 V 2.5 A 8 mA 695 mA 15.0 V 90% 1200 μF JCM3048S12 15 V 2.0 A 8 mA 685 mA 18.0 V 91% 1000 μF JCM3048S15 ±12 V ±1.25 A 8 mA 685 mA ±15.0 V 91% ±750 μF JCM3048D12 ±15 V ±1.0 A 8 mA 680 mA ±18.0 V 92% ±500 μF JCM3048D15 18-36 V 36-75 V JCM3024S3V3 JCM3048S3V3 Notes 1. Input currents measured at nominal input voltage. 2. Maximum capacitive load is per output. 3. Add suffix ‘-HK’ for optional Heat Sink. Mechanical Details 0.1 (2.54) Top View 0.4 (10.16) 4 6 5 2 1 1.0 (25.4) Notes 1 0.1 (2.54) 1. All dimensions are in inches (mm) 2. Weight: 0.042 lbs (19 g) approx. 3. Pin diameter: 0.04±0.002 (1.0 ±0.05) 1 0.2 (5.08) 0.5 (0.02) 0.41 (10.4) 2 0.1 (2.54) Pin 1 2 0.04 (1.0) 1.0 (25.4) DIA 0.04 (1.0) 3 4 5 6 3 0.3 (7.62) Pin Connections 0.66 (16.8) 1.0 (25.4) Print Face 0.6 (15.24) 0.8 (20.32) 3 0.1 (2.54) 6 5 4 1.0 (25.4) 0.4 (10.16) 0.24 (6.0) 4. Pin pitch tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) www.xppower.com Single +Vin -Vin Dual +Vin -Vin Remote Remote On/Off On/Off +Vout Trim -Vout +Vout Common -Vout JCM30 Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Minimum Maximum Units Notes & Conditions 9 Typical 18 VDC 12 V nominal 18 36 VDC 24 V nominal 36 75 VDC 48 V nominal 25 50 mA pk-pk VDC for 100 ms VDC for 100 ms Through 12 μH inductor and 47 μF capacitor 12 V models 24 V models 100 VDC for 100 ms 48 V models Maximum Units Notes & Conditions 30 VDC See Models and Ratings table Input Reflected Ripple Current 30 Input Surge Output Characteristic Minimum Output Voltage 3.3 Output Trim ±10 Typical Initial Set Accuracy Minimum Load ±1 0 % Single Output Versions % At full load % No minimum load required From minimum to maximum input at full load Line Regulation ±0.5 % Load Regulation 0.5/1.0 % From 0% to full load for single/dual output ±5 % On dual output models, when one output is at 100% load and other is varied from 25% load to full load 75/60 mV pk-pk Cross Regulation Ripple & Noise Overload Protection 150 % Short Circuit Protection Continuous trip and restart (hiccup), with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ ˚C Over Protection Voltage Remote On/Off Single output 10 μF X7R MLCC Dual output with 10 μF/25 V X7R MLCC on each output measured using 20 MHz bandwidth See Models and Ratings table Output is on if remote on/off (pin 3) is open or high (3.0 to 12 VDC) Output turns off if remote on/off (pin 3) is low (