JPS250PQ41

ACDC 250/350 Watts xppower.com JPS250/350 Series • 200 W / 300 W with Convection Cooling • High Efficiency  up to 88% • Meets 1U, Low Profile Requirements • AC OK & DC OK Signals • Zero Voltage Switching Technology • Remote On/Off & Remote Sense • 3 Year Warranty Specification Input General • 85-264 VAC (170-370 VDC) • 47-63 Hz • 2.75 A/1.40 A max at 115 VAC/ 230 VAC (JPS250) 4.5 A/2.2 A max at 115 VAC/230 VAC (JPS350) Inrush Current • 30 A at 115 VAC, 60 A at 230 VAC Power Factor • 0.9 typical Earth Leakage Current • 3.0 mA max 264 VAC/60 Hz Input Protection • Internal T5 A, 250 VAC fuse (JPS250) Internal T6.3 A, 250 VAC fuse (JPS350) Input Voltage Input Frequency Input Current Efficiency Isolation Switching Frequency Power Density Signals MTBF Output • See tables • ±10% on output 1 only (VR1) • At 60% rated load ±1% on V1 & V2, ±5% on V3 & V4 Minimum Load • Single output models: No minimum load required. Multi-output models, see note 4 Start Up Delay • 2 s typical Start Up Rise Time • 80 ms typical (JPS250) 100 ms typical (JPS350) Hold Up Time • 20 ms min at low line & rated load Line Regulation • ±0.5% at rated load across input voltage range Load Regulation • ±1% for single output models & V1 & V2 of multi-output models, ±5% for V3 & V4 Transient Response • 4% max deviation, recovery to within 1% in 500 µs for a 25% load change Ripple & Noise • ±1% max pk-pk, 15 MHz bandwidth, see note 2 under model tables Overvoltage Protection • 115-140% on single outputs & V1 of quad output models, recycle input to reset Overtemperature • Shuts down at +110 °C, auto recovery, Protection measured internally Overload Protection • 110-130% of max rated load on all O/Ps, auto recovery Short Circuit Protection • Trip and restart (Hiccup mode), auto recovery Temp. Coefficient • ±0.05%/°C Remote Sense • Compensates for up to 0.5 V drop Output Voltage Output Voltage Trim Initial Set Accuracy Remote On/Off Current Share Fan Output • On = Logic Low or Open, Off = Logic High • Current share on single output models & V1 & V2 of multi-output models (4 supplies can be paralleled) • See mechanical notes for ordering information • Up to 88% • 3000 VAC Input to Output 1500 VAC Input to Ground 500 VAC Output to Ground • 120 kHz typical for PFC and PWM • 4.96 W/In3 • AC OK, DC OK, Remote On/Off (see control and supervisory signals) • 125 kHrs to MIL-HDBK-217F at +50 °C, GB (JPS250) 146 kHrs to MIL-HDBK-217F at +50 °C, GB (JPS350) Environmental Operating Temperature • 0 °C to +70 °C, (see derating curve) Full power to +50 °C Cooling • 250 W with 18 CFM airflow (JPS250) 200 W convection cooling (JPS250) 350 W with 18 CFM airflow (JPS350) 300 W convection cooling (JPS350) Operating Humidity • 5-95% RH, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 2000 m Vibration • 2 g, 10 Hz to 55 Hz, 30 mins each axis EMC & Safety Emissions Harmonic Currents ESD Immunity Radiated Immunity EFT/Burst Surge Dips and Interruptions Safety Approvals • EN55022, level B conducted FCC 20780, level B conducted • EN61000-3-2 • EN61000-4-2, level 3 Perf Criteria A • EN61000-4-3, 10 V/m Perf Criteria A • EN61000-4-4, level 3 Perf Criteria A • EN61000-4-5, level 3 Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B • EN60950-1, UL60950-1, CSA C22.2 No. 60950-1, CE Mark LVD Output Power(1) Convection-cooled 18 CFM 225 W 250 W Output Current Output Voltage Ripple & Noise Pk-Pk Model Number(3) 5V 36.0 A 45.0 A 50 mV JPS250PS05C 12 V 17.0 A 21.0 A 120 mV JPS250PS12C 15 V 13.5 A 17.0 A 120 mV JPS250PS15C 24 V 8.5 A 10.4 A 200 mV JPS250PS24C 48 V 4.3 A 5.2 A 200 mV JPS250PS48C Notes 1. Maximum power with 18 CFM forced air is 250 W, or 200 W with convection cooling. 2. Ripple and noise measured over 15 MHz bandwidth with a 0.47 µF capacitor. 3. For non-current share version delete suffix ‘C’ from model number. Mechanical Details All models (except JPS250PS05) 8.00 (203.2) A B B L Pin A VR1 10 TB4 Voltage Adj. N 2 E TB1 1 + - TB3 1 3.75 (95.3) 4.20 (106.7) TB2 TRANSFORMER 6 A B B A 5.50 (139.0) 6.50 (165.1) 0.30 (7.6) 0.75 (19.1) TB4 All models 1 +5 V +V Signal 0 V 2 +5 V +V DC OK 3 0V +V AC OK 4 0V 0V Remote On/Off 5 0V 0V +Sense 6 0V 0V 7 +5 V Current Share(5) 8 +5 V N/C -Sense 9 N/C 10 N/C 7.40 (188.0) A A B B 1.51 (38.3) JPS250PS05 8.00 (203.2) A VR1 B 2 10 TB4 Voltage Adj. L 1 N 1 E TB1 4.20 (106.7) TB2 TRANSFORMER TB3 A + - 1.30 (32.1) 5.50 (139.0) 0.70 (19.1) 6.50 (165.1) Fixing Holes: A = #6-32 screw mounting holes B = M3 x 0.5 screw mounting holes Maximum mounting screw penetration is 0.16 (4.0) from chassis outer surface. 8 B B Notes 1. TB3 is for fan, with Molex 5045-02A or equivalent. 5 V model: 5 V at 390 mA, 24 V model: 24 V at 80 mA, all other models: 12 V at 112 mA 2. TB1 (AC input) and TB2 (DC output) are terminal blocks. 3. TB4 signal connector is Molex 70246-10 or equivalent. 4. Fan cover option available, order part number: 5 V models: JPS250 F/CVR 5 12, 15 & 48 V models: JPS250 F/CVR 24 V models: JPS250 F/CVR 24 Or add suffix ‘-E’ to model number to receive unit with fan cover fitted. 4.2 x 8 x 2.48 (106.7 x 203.2 x 62.9). 5. For current share operation connect current share (pin 7) between units. For non ‘C’ models pin 7 (current share) is not used. 6. Input and output terminal screw tightening torque 9 lbs-in (1.0 Nm) maximum. 0.36 (9.1) 3.75 (95.3) PIN CONNECTIONS TB2 JPS250PS05 All other models A All dimensions are in inches (mm) Tolerance: ±0.03 (0.8) max Weight: 1.65 lbs (750 g) approx. ACDC JPS250  Single Output Models and Ratings ACDC JPS250  Multi Output Models and Ratings Output 1 Output 2 Output V1 Conv. Cooled Max 18 CFM 3.3 V 16.0 A 5.0 V 17.5 A 5.0 V 5.0 V Output 3 Output V2 Conv. Cooled Max 18 CFM 20 A 5V 12 A 30 A 12 V 7A 20.0 A 25 A 12 V 20.0 A 25 A 15 V Output 4 Model Number(3) Output V3 Conv. Cooled Max 18 CFM Output V4 Conv. Cooled Max 18 CFM 20 A 12 V 5A 6A -12 V 1A 2A JPS250PQ46C 8A -12 V 2A 3A -5 V 1A 2A JPS250PQ41C 4A 6A 24 V 2A 3A -12 V 1A 2A JPS250PQ47C 3A 5A 24 V 2A 3A -15 V 1A 2A JPS250PQ48C Notes 1. 2. 3. 4. Maximum power with 18 CFM forced air is 250 W, or 200 W with convection cooling. Ripple and noise measured over 15 MHz bandwidth with a 0.47 µF capacitor. For non current share option delete suffix ‘C’ from model number. All models require 2 A minimum load on V1. On V2, JPS250PQ46 requires 1 A and JPS250PQ41 requires 0.5 A. † Available from Farnell. See pages 266-269. ^ Available from Newark. See pages 270-272. Mechanical Details 8.00 (203.2) L 1 N Voltage Adj. E TB3 TRANSFORMER TB1 10 2 VR1 TB2 VR2 8 1 4.20 (106.7) Safety earth connection + - 0.30 (7.6) 0.75 (19.1) TB5 A A B B 1 2 3 4 5 6 7 8 9 10 +5 V +5 V 0V 0V 0V -5 V -12 V +12 V Pin PQ41 1 2 3 4 5 6 7 8 9 10 +5 V +S +5 V PS(5) +12 V +S DC OK +12 V -S +5 V -S +12 V PS(5) Remote On/Off AC OK 0V 1.30 1.50 (33.1) (38.1) 0.36 (9.1) 8.00 (203.2) B B A B B A 3.75 (95.3) 1.30 (32.1) 0.70 (19.1) A PQ41 PIN CONNECTIONS - TB3 PQ46 PQ47 +12 V -12 V +5 V +5 V 0V 0V 0V 0V +3.3 V +3.3 V +5 V +5 V 0V 0V 0V -12 V +24 V +12 V PQ48 +5 V +5 V 0V 0V 0V -15 V +24 V +15 V 0.16 (4.0) 7.40 (187.9) A Pin PIN CONNECTIONS - TB2 PQ46 PQ47 +3.3 V +S +5 V -S +3.3 V PS(5) DC OK +5 V +S +3.3 V -S +5 V PS(5) Remote On/Off AC OK 0V +5 V +S +5 V PS(5) +12 V +S DC OK +12 V -S +5 V -S +12 V PS(5) Remote On/Off AC OK 0V PQ48 +5 V +S +5 V PS(5) +15 V +S DC OK +15 V -S +5 V -S +15 V PS(5) Remote On/Off AC OK 0V Notes 0.22 (5.7) 5.50 (139.0) 6.50 (165.1) Fixing Holes: A = #6-32 screw mounting holes B = M3 x 0.5 screw mounting holes Maximum mounting screw penetration is 0.16 (4.0) from chassis outer surface. All dimensions are in inches (mm). Tolerance: ±0.03 (0.8) max. Weight: 1.65 lbs (750 g) approx. 1. TB5 is for fan with Molex 5045-02A or equivalent. 12 V at 112 mA. 2. TB1 (AC input) and TB3 (DC output) are terminal blocks. 3. TB2 signal connector is Molex 70246-10 or equivalent. 4. Fan cover option available, order part number: PQ41, PQ46 & PQ47: JPS250 F/CVR PQ48: JPS250 F/CVR 24 or add suffix ‘-E’ to model number to receive unit with fan cover fitted. 4.2 x 8 x 2.48 (106.7 x 203.2 x 62.9). 5. PS - Current share on ‘C’ models only. No connection on standard models. 6. VR2 is for production setting only. 7. Input terminal screw tightening torque 9 lbs-in (1.0 Nm) maximum. 8. Output terminal screw tightening torque 4 lbs-in (0.45 Nm) maximum. Output Power Output Current Output Voltage 315 W 350 W Convection-cooled 18 CFM Ripple & Noise Pk-Pk(2) Model Number(1) 5V 54.0 A 63.0 A 50 mV JPS350PS05C 12 V 25.0 A 30.0 A 120 mV JPS350PS12C 15 V 20.0 A 24.0 A 120 mV JPS350PS15C 24 V 13.0 A 15.0 A 200 mV JPS350PS24C 48 V 6.5 A 7.3 A 200 mV JPS350PS48C Notes 1. For non-current share version delete suffix ‘C’ from model number. 2. Ripple and noise measured over 15 MHz bandwidth with a 47 µF electrolytic capacitor and 0.47 µF ceramic capacitor. † Available from Farnell. See pages 266-269. ^ Available from Newark. See pages 270-272. Mechanical Details All models (except JPS350PS05) Pin 9.00 (228.6) A L A B B N 1 E TB1 4.50 (114.3) 5.00 (127.0) TRANSFORMER 6 TB2 10 2 Voltage Adj. A 1 + TB3 TB4 A B B VR1 0.25 (6.75) 0.75 (19.1) 6.50 (164.4) 1 +5 V +V 2 +5 V +V N/C N/C 3 0V +V +Remote sense 4 0V 0V DC OK 5 0V 0V -Remote sense 6 0V 0V 7 +5 V Current Share(5) 8 +5 V Remote On/Off N/C 9 AC OK 10 0V 8.00 (203.2) A A B B 1.60 (40.6) 0.47 (12.0) JPS350PS05 9.00 (228.6) A B B A 1. TB3 is for fan, with Molex 5045-02A or equivalent. 12 V at 112 mA (except JPS350PS05, 5 V at 390 mA). 2. TB1 (AC input) and TB2 (DC output) are terminal blocks. 3. TB4 signal connector is Molex 70246-10 or equivalent. 4. Fan cover option available, order part number: 5 V models: JPS350 F/CVR 5 All other models: JPS350 F/CVR Alternatively, add suffix ‘-E’ to model number to receive fan cover fitted to the unit 4.95 x 8.92 x 2.48 (127.0 x 228.6 x 62.9). 5. For current share operation, connect current share (pin 7) between units. For non ‘C’ models pin 7 is not used. 6. Input and output terminal screw tightening torque 9 lbs-in (1.0 Nm) maximum. TB4 VR1 N Notes 12 Voltage Adj. L 10 E 1 TB1 TRANSFORMER 4.50 (114.3) 5.00 (127.0) Fixing Holes: A = #6-32 screw mounting holes B = M3 x 0.5 screw mounting holes Maximum mounting screw penetration is 0.16 (4.0) from chassis outer surface. 8 TB3 A 0.25 (6.75) TB4 All models 7.50 (190.5) 0.50 (12.7) 0.87 (22.0) PIN CONNECTIONS TB2 JPS350PS05 All other models 0.75 (19.1) B + 6.50 (164.4) 7.50 (190.5) TB2 B A All dimensions are in inches (mm) Tolerance: ±0.03 (0.8) max. Weight: 2.12 lbs (960 g) approx. ACDC JPS350  Single Output Models and Ratings ACDC JPS250/350 Control & Supervisory Signals AC OK Signal DC OK Signal +5 V +5 V 330 R 330 R AC OK (HIGH) DC OK (HIGH) AC OK DC OK GND GND DC NOT OK (LOW) AC NOT OK (LOW) AC OK is a TTL signal which goes LOW when input falls out of specification. Source current is 1 mA, sink current is 6 mA. DC OK is a TTL signal which goes LOW when PSU is in an overcurrent condition, overvoltage condition, disabled or when output falls out of regulation. Source current is 1 mA, sink current is 6 mA. Remote On/Off Control (Inhibit) Parallel Connection Utilizing Optional Current Share Supply 1 OUTPUTS OFF (5V) Remote On/Off Output Return Current Share V1 Ground OUTPUTS ON (0 V or open circuit) Supply 2 Output Return Current Share To turn off the output, apply 5 V to the remote On/Off. Remote Sense Connection Output + Sense + CD + Twisted Pair Supply LOAD CL Sense - Output - CD Notes: 1. CD is 0.1 µF ceramic capacitor. LOAD Return 2. CL i s 47 µF electrolytic capacitor. Derating Curve 100 90 80 L O 70 A 60 D 50 40 %) 30 20 10 0 JPS250PS with 18 CFM Fan JPS250PS Convection-cooled 0 10 20 30 40 50 Ambient Temperature (˚C) 60 70 80 60 70 80 JPS350 with 18 CFM Fan 100 90 80 L O 70 A 60 D 50 40 (%) 30 20 10 0 JPS350 Convection-cooled 0 10 20 30 40 50 Ambient Temperature (°C) Cover Option See mechanical details notes for ordering information. 1.70 (43.2) 2.48 (62.9) Typical internal clearance 0.15 (3.8) 4 x M3 x 6 C/S head fixing screws in existing countersunk holes 11-Apr-11 ACDC JPS250/350 Control & Supervisory Signals