JTL6048S12

JTL60 Series DC-DC Converter XP Power 60 Watts xxx Series • Single and Dual Outputs • Wide 4:1 Input Range • 2” x 1” Footprint • -40 °C to +85 °C Operation • Full Load at 50 °C Ambient • 1600 VDC Isolation • Output Trim ±10% • Remote On/Off • 3 Year Warranty Dimensions: JTL60: 2.0 x 1.0 x 0.45” (50.8 x 25.4 x 11.5 mm) The JTL60 series provides a compact, highly efficient and cost effective 60W DC-DC power supply in a potted construction using a copper case for pcb mounting. Features include soft start, over temperature protection, over voltage and over current protection. Models & Ratings Input Voltage Output Voltage 9-36 V Input Current(1) Output Current No Load Full Load OVP setting Efficiency Max. capacitive load(2) Model Number(3) 5.0 V 12.0 A 25 mA 2705 mA 6.2 V 92% 30,000 μF JTL6024S05 12.0 V 5.0 A 25 mA 2705 mA 15.0 V 92% 5850 μF JTL6024S12 15.0 V 4.0 A 25 mA 2690 mA 20.0 V 93% 3900 μF JTL6024S15 ±12.0 V ±2.5 A 40 mA 2750 mA ±15.0 V 91% ±3900 μF JTL6024D12 ±15.0 V ±2.0 A 50 mA 2730 mA ±20.0 V 91% ±2400 μF JTL6024D15 5V 12.0 A 25 mA 1345 mA 6.2 V 93% 30,000 μF JTL6048S05 12 V 5.0 A 25 mA 1350 mA 15.0 V 92% 5850 μF JTL6048S12 15 V 4.0 A 25 mA 1345 mA 20.0 V 93% 3900 μF JTL6048S15 ±12 V ±2.5 A 40 mA 1375 mA ±15.0 V 91% ±3900 μF JTL6048D12 ±15 V ±2.0 A 50 mA 1375 mA ±20.0 V 91% ±2400 μF JTL6048D15 18-75 V Notes 1. Input currents measured at nominal input voltage. 2. Maximum capacitive load is per output. 3. Add suffix ‘-HK’ for optional heatsink Mechanical Details Optional Heatsink (-HK) 0.10 (2.54) 0.10 (2.54) 0.40 0.40 (10.16) (10.16) 5 4 0.45 (11.5) 0.10 (2.54) Print Face 2.0 (50.8) Bottom View 0.10 (2.54) 0.10 (2.54) 2 2.0 (50.8) TOP Dia 0.04 (1.0) Pin Connections Single Dual +Vin +Vin -Vin -Vin Remote On/Off Remote On/Off +Vout +Vout -Vout Common Trim -Vout Notes Dimensions inches (mm) 3 0.20 (5.08) 0.60 (15.24) 1 Pin 1 2 3 4 5 6 6 0.10 (2.59) 1 0.69 (17.6) 0.24 (6.0) 1.0 (25.4) Heat-sink Thermal Pad Converter www.xppower.com 1. 2. 3. 4. Pin diameter 0.04 ±0.002 (1.0 ±0.05) Pin pitch and length tolerance ±0.014 (±0.35) Case tolerance +±0.02 (±0.5) Stand-off tolerance ±0.004 (±0.1) JTL60 Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Minimum Maximum Units Notes & Conditions 9 Typical 36 VDC 24 V nominal 18 75 VDC 48 V nominal Input Reflected Ripple Current 20 Input Surge mA pk-pk Through 11 μH inductor and 22 μF capacitor 50 VDC for 100 ms 24 V models 100 VDC for 100 ms 48 V models Maximum Units Notes & Conditions 30 VDC See Models and Ratings table Output Characteristic Minimum Output Voltage 5.0 Output Trim ±10 Typical Initial Set Accuracy Minimum Load ±1 0 % See Application Note % At full load % No minimum load required From minimum to maximum input at full load Line Regulation ±0.5 % Load Regulation 0.5/1.0 `% From 0% to full load for single/dual output % On dual output models, when one output is at 100% load and other is varied from 25% load to full load Cross Regulation ±5 Start Up Time 60 Ripple & Noise Overload Protection 120 ms 100 mV pk-pk 140 % Short Circuit Protection Continuous hiccup mode, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ ˚C Overvoltage Protection Remote On/Off Measured using 20 MHz bandwidth and 1.0 μF ceramic capacitor See Models and Ratings table Output is on if remote on/off (pin 3) is open or high (3-12 VDC), relative to -Vin (pin 2) Output turns off if remote on/off (pin 3) is low (