PBM200PQ06-C

AC-DC 200 Watts xppower.com PBM200 Series • Worldwide Medical Approvals • Single, Dual, Triple and Quad Outputs • Power Fail Detect • Remote On/Off • U-Channel and Enclosed Versions • 100 Watt Convection-cooled Rating • 3 Year Warranty Specification Input General Input Voltage Input Frequency Input Current • 90-264 VAC • 47-63 Hz • 3.2 A rms at 115 VAC, 1.6 A rms at 230 VAC Inrush Current • 20 A at 115 VAC, 40 A at 230 VAC cold start 25 °C Power Factor • 0.98 typical Earth Leakage Current • 90 μA max at 115 VAC/60 Hz 150 μA max at 230 VAC/50 Hz Input Protection • Internal T4 A/250 V in line and neutral Output Switching Frequency Signals Power Density Power Fail Detect MTBF • 80% maximum • 4000 VAC Input to Output 1500 VAC Input to Ground 500 VAC Output to Ground • 100 kHz ±12 kHz • Power fail detect, remote on/off • 4.76 W/In3 • AC OK = TTL logic high AC not OK = TTL logic low • 350 kHrs to MIL-HDBK-217F at +25 °C, GB Environmental Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Drift Line Regulation Load Regulation Transient Response • • • • • • • • • • • Ripple & Noise • Overvoltage Protection • Overtemperature Protection • Overload Protection Short Circuit Protection Temperature Coefficient Remote Sense • • • Remote On/Off Efficiency Isolation See table Not user-adjustable ±2% See table & note 5 2 s max 18 ms typical 20 ms minimum at full load & 110 VAC ±0.2% ±0.5% max See note 7 4% max deviation, recovery to within 1% in 500 μs for a 25% load change 2% max pk-pk, 20 MHz bandwidth with a 22 μF electrolytic & a 0.47 μF tantalum capacitor 112-140% Vnom output 1 only, recycle input to reset Shutdown at +85 °C (singles) or +105 °C (multi outputs) with auto recovery, measured internally 110-150% typical, auto recovery Trip and restart (Hiccup mode) 0.04%/°C • Single output models only. Compensates for up to 0.5 V drop • On = Logic low or open circuit Off = Logic high Operating Temperature • 0 °C to +70 °C, derate linearly from 100% power at +50 °C to 50% power at +70 °C Cooling • ‘C’ versions have internal fan, ‘B’ versions are derated with convection cooling or require 25 CFM (see note 4) Operating Humidity • Up to 95% RH, non-condensing Storage Temperature • -40 °C to +85 °C Operating Altitude • 2500 m Shock • Half sine pulse. acceleration 50 g, 11 ms duration, 3 shocks in each direction, unpackaged, non-operating Vibration • Sinusoidal 10-55 Hz, amplitude 0.15 mm, 30 min/axis, unpackaged, non-operating EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55011 & FCC Class B conducted & radiated • EN61000-3-2, Class A • EN61000-3-3 • EN61000-4-2, level 3 Perf Criteria A • EN61000-4-3, level 3 Perf Criteria A • EN61000-4-4, level 3 Perf Criteria A • EN61000-4-5, level 3 Perf Criteria A • EN61000-4-6 3 V, Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms, Perf Criteria A, B, B • EN60601-1, UL60601-1, CSA22.2 No. 601-1 per cUL, CE & UKCA meets all applicable directives & legislation. Output 1(8) Output Power(4) Vnom Output 2(2,5) Imin Imax Reg (5) (7) Vnom Imax Output 3(5) Reg (7) Vnom Imax Output 4(3,5) Reg (7) Vnom Imax Reg(7) Model Number(1) 150 W 3.3 V 3.0 A 46.0 A 3% PBM200PS3V3-C 175 W 5.1 V 3.0 A 35.0 A 2% PBM200PS05-C 200 W 12.0 V 1.2 A 16.7 A 2% PBM200PS12-C 200 W 15.0 V 1.0 A 13.4 A 2% PBM200PS15-C 200 W 24.0 V 0.6 A 8.4 A 2% PBM200PS24-C 200 W 30.0 V 0.5 A 6.7 A 2% PBM200PS30-C 200 W 48.0 V 0.5 A 4.2 A 2% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% PBM200PD01-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% PBM200PD02-C 200 W +5.1 V 3.0 A 30.0 A 2% +24 V 4.0 A 4% PBM200PD03-C 200 W +12.0 V 1.0 A 8.7 A 2% +24 V 4.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -5 V 6.0 A 4% PBM200PT01-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 4% PBM200PT02-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -15 V 4.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -12 V 4.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -15 V 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 175 W +3.3 V 3.0 A 30.0 A 3% +5.1 V PBM200PS48-C PBM200PD04-C PBM200PT03-C F 24 V 4.0 A 4% PBM200PT04-C 4% F 5V 6.0 A 4% PBM200PQ01-C 4.0 A 4% F 24 V 4.0 A 4% PBM200PQ02-C -12 V 4.0 A 4% F 12 V 4.0 A 4% PBM200PQ03-C 4% -15 V 4.0 A 4% F 15 V 4.0 A 4% PBM200PQ04-C 8.0 A 4% -12 V 4.0 A 4% F 24 V 4.0 A 4% PBM200PQ05-C 8.0 A 4% -12 V 4.0 A 4% F 12 V 4.0 A 4% PBM200PQ06-C PBM200PT05-C Notes 1. For U-bracket format, replace suffix ‘-C’ with suffix ‘-B’. 2. Output 2 peak current is 12 A on +12 V, 9 A on +15 V, and 6 A on +24 V. Maximum 2 s duration with total load