PBR650PS24C

PBR650 Series AC-DC Power Supplies 650 Watts • Medical (BF) Safety Approvals • 4” x 8” Package • 5V Standby & 12V Fan Supply • AC OK, Inhibit & Remote Sense • Class B Conducted & Radiated Emissions • 3 Year Warranty The PBR650 series of AC-DC switching power supplies, in a package of just 4 x 8 x 2.58 inches, deliver 600-650 watts of continuous power. They are designed for medical applications including those needing BF rated insulation with an operation altitude of up to 5000m. Dimensions: PBR650: 8.00 x 4.00 x 2.58” (203.2 x 101.6 x 65.5 mm) Models & Ratings Output Voltage V1 Output Current V1(2) Nominal Standby Supply V2 Ripple & Noise(1) Model Number Peak(3) 12 V 50.00 A 55.00 A 120 mV PBR650PS12 15 V 40.00 A 44.00 A 150 mV PBR650PS15 18 V 36.12 A 40.00 A 180 mV PBR650PS18 24 V 27.09 A 30.00 A 240 mV PBR650PS24 28 V 23.22 A 25.50 A 280 mV PBR650PS28 36 V 18.06 A 20.00 A 360 mV PBR650PS36 48 V 13.55 A 15.00 A 480 mV PBR650PS48 57 V 11.41 A 12.50 A 570 mV PBR650PS57 5.0 V / 0.2 A Notes 1. Ripple and noise is the maximum peak-to-peak voltage value measured at the output with 20 MHz bandwidth, at rated line voltage and output load, and with a 10 µF tantalum capacitor in parallel with a 0.1 µF ceramic capacitor. 2. All models may be operated at no-load without damage. At no load, output voltage fluctuates beyond 5% due to burst-mode operation of the control IC for energy saving. 3. Peak current available for 15s max, 10% duty cycle, average power not to exceed nominal power rating. Temperature Derating Curve Output Power 100% 50% 0% -10 50 Ambient Temperature (ºC) 1 www.xppower.com 70 PBR650 Series AC-DC Power Supplies Input Maximum Units Notes & Conditions Input Voltage 80 264 VAC Derate to 90% at 85 VAC & 80%at 80 VAC Input Frequency 47 63 Hz Characteristic Minimum Input Current - Full Load Typical 8.4/4.2 Earth Leakage Current A (rms) 225 275 µA Typical Maximum Units 57 VDC 115/230 VAC, 60/50 Hz 264 VAC, 63 Hz Output Characteristic Minimum Output Voltage 12 Notes & Conditions See Models and Ratings table Tolerance ±2 % Line and Load Regulation, 0.1% minimum load required to meet specification Transient Response 4 % Recovery within 1% in less than 500 µs for a 25% step load change 1 % pk-pk Overvoltage Protection Ripple & Noise 115 140 % Overcurrent Protection 115 140 % 20 MHz bandwidth, see model table notes Latching Trip & restart characteristic Protected for overtemperature conditions Thermal Shutdown Temperature Coefficient ±0.04 %/°C 5 V Standby Supply 5 V At 200 mA Fan Supply 12 V At 500 mA 50 80 µA 264 VAC, 63 Hz Typical Patient Leakage Current Environmental Characteristic Maximum Units Operating Temperature -10 +70 °C Storage Temperature -40 +85 °C 5 95 %RH Non-condensing Maximum Units Notes & Conditions Humidity Minimum Notes & Conditions Derate Linearly from 100% load at +50 °C to 50% load at +70 °C General Characteristic Minimum Efficiency Isolation: Input to Output Input to Ground Output to Ground 90 4000 Inrush Current Mean Time Between Failure Weight % VAC 230 VAC, 100% load 2 x MOPP 1500 VAC 1 X MOPP 1500 VAC 1 X MOPP 85 Switching Frequency Hold Up Time Typical 12 kHz 20 ms 30/60 VAC 115 VAC/230 VAC at 25 °C, cold start 190,000 Hrs MIL-HDBK-217F, Full load at 25 °C GB 4.4 (2000) lb (g) www.xppower.com At 110 VAC & 500 W 2 PBR650 Series AC-DC Power Supplies Signals & Controls Characteristic Notes & Conditions Remote Sense Compensates for 0.5 V total voltage drop. Inhibit To inhibit apply TTL high signal . AC OK TTL high for normal operation, low upon loss of input power, turn-on delay time 100-1000 ms, turn-off delay time 1 ms minimum EMC: Emissions Phenomenon Conducted Test Level Standard EN55011/EN55032 Class B Radiated EN55011/EN55032 Class B Harmonic Current EN61000-3-2 Class A Voltage Fluctuations EN61000-3-3 Notes & Conditions EMC: Immunity Phenomenon Test Level Criteria EN61000-4-2 4 A Radiated EN61000-4-3 10 V/m A EFT EN61000-4-4 ±2 kV A ESD Standard Surges EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 10 rms A Magnetic Field EN61000-4-8 30 A/m A 400 W (100 VAC/60 Hz) 400 W (230 VAC/50 Hz) Dips and Interruptions 500 W (100 VAC/60 Hz) 500 W (230 VAC/60 Hz) Dip 30% (70 VAC), 500ms A Dip 60% (40 VAC), 100ms B Int >95% (0 VAC), 10ms A Int 100% (0 VAC), 20ms A Int 100% (0 VAC), 5000ms B Dip 30% (161 VAC), 500ms A Dip 60% (92 VAC), 100ms A Int >95% (0 VAC), 10ms A Int 100% (0 VAC), 20ms A Int 100% (0 VAC), 5000ms B Dip 30% (70 VAC), 500ms A Dip 60% (40 VAC), 100ms B Int >95% (0 VAC), 10ms A Int 100% (0 VAC), 20ms A Int 100% (0 VAC), 5000ms B Dip 30% (161 VAC), 500ms A Dip 60% (92 VAC), 100ms A Int >95% (0 VAC), 10ms A Int 100% (0 VAC), 20ms A Int 100% (0 VAC), 5000ms B Notes & Conditions ±8 kV contact, ±15 kV air ±1 kV differential/ ±2 kV common mode Safety Approvals Safety Agency CB Report UL TUV 3 Safety Standard Notes & Conditions IEC60950-1 Information Technology IEC62368-1 Information Technology IEC60601-1 Including Risk Management Medical ES60601-1, CSA C22.2 No.60601-1 Medical UL62368-1, CSA C22.2 No. 62368-1 Information Technology EN60601-1 Medical EN62368-1 Information Technology www.xppower.com PBR650 Series AC-DC Power Supplies Mechanical Details Mounting holes, threaded insert for M3*0.5 screws (8 places) P1 2.86 (72.6) G L N P2 4.00 (101.6) P3 P3 Vadj 2.83 (65.5) 6.53 (165.8) 0.87 (22.2) P3 8.00(203.2) PCB 1.95 (49.5) Input Connector - P1 Output Connector - P2 P3 Pin 1 G Pin 1 +V1 Pin 1 +V1 Sense Pin 2 L Pin 2 +V1 Pin 2 +V1 Sense Pin 3 N Pin 3 +V1 Pin 3 AC OK Pin 4 Com Pin 4 Common Return Pin 5 Com Pin 5 N/C Pin 6 Com Pin 6 N/C Pin 7 Inhibit Mates with JST VHR-3N housing and SVH-21T-P1.1 crimps Mates with JST VHR-6N housing and SVH-21T-P1.1 crimps Pin 8 N/C Pin 9 +5V Standby Pin 10 +5V Standby Return Mates with Molex 22-01-1022 housing and 2759 crimps Notes 1. Dimensions shown in inches [mm] 6. Weight: 2.0 Kg (2.23 lbs.) approx. 2. Tolerance 0.02 [0.5] maximum 7. Maximum penetration of fixing screws is 4 mm from the outer surface of chassis. 3. Input connector P1 is Dinkle terminal P/N DT-35C-B01W-03, with nickel plated M3 screws. 4. Output connector P2 are M4x0.7 screw connections. 5. Connector P3 is Molex header 87833-08 or equivalent, mating with Molex housing 51110-0850 or equivalent. www.xppower.com 26 Feb 19