SHP650PS15-EF

SHP350 Series • 420 W High Line Output Power • Rugged Industrial Construction • Variable Speed Fan for Noise Reduction • -40 °C to +70 °C Operation • 5 V Standby • AC OK, Remote On/Off and Active Current Share • Screw Terminals • SEMI F47 Compliant • 3 Year Warranty The SHP350 AC-DC power supply provides upto 420 W of output power in a compact rugged mechanical package, suitable for a range of industrial applications. The unit comprises of a main output with voltages from 12-48 VDC and a 5 VDC standby supply which can be utilitsed with the signals and control features of the unit to provide detection of loss of AC input and remote on/off control. Multiple units can be used in parallel via the current share facility, providing higher power solutions. Inherently low earth leakage current, and conducted EMC compliance to Class B also simplify higher power system design. Packaged in a compact 7” (178 mm) x 3.6” (91 mm) x 2.1” (53 mm) and carrying IEC60950 family safety approvals, the SHP350 has a load dependant variable speed fan, is fully protected with overtemperature shutdown and provides -40 ºC start up and full power from -20 ºC to 50 ºC and 50% power at +70 ºC. xppower.com Models and Ratings Output Voltage V1 Output Current V1 12 V 15 V 24 V 28 V 36 V 48 V Standby Supply V2 26.5 A 22.0 A 14.5 A 12.5 A 9.7 A 7.3 A 5V 5V 5V 5V 5V 5V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 Output Power Continuous A A A A A A Peak Model Number 318 W 330 W 348 W 350 W 350 W 350 W 417 W 420 W 420 W 420 W SHP350PS12 SHP350PS15 SHP350PS24 SHP350PS28 SHP350PS36 SHP350PS48 Input Characteristics Characteristic Input Voltage - Operating Input Frequency Minimum 85 47 Typical 115/230 50/60 Units VAC Hz 0.15 A 3.8/2.1 A 115/230 VAC A µA 230 VAC cold start, 25 ºC 115/230 VAC/50 Hz (Typ.), 264 VAC/60 Hz (Max.) 60 150/260 500 T10 A/250 V internal fuse in both lines Input Derating Curve Notes & Conditions Derate output power < 90 VAC. See fig. 1. EN61000-3-2 class A compliant, Class C compliant ≥10% load >0.9 Power Factor Input Current - No Load Input Current - Full Load (350 W) Inrush Current Earth Leakage Current Input Protection Maximum 264 63 100 Figure 1 Output Power (%) 90 80 70 60 50 40 85 90 264 Input Voltage (VAC) 2 xppower.com Output Characteristics Characteristic Output Voltage - V1 Initial Set Accuracy Output Voltage Adjustment Minimum Load Start Up Delay Hold Up Time Drift Line Regulation Load Regulation Minimum 12 Typical Maximum 48 ±1 (V1) , ±5 (V2) ±10 ±0.2 ±0.5 ±1 (V1) , ±5 (V2) Units VDC % % A s ms % % % 4 % 145 140 % pk-pk % % I nom 0 0.5 20 Transient Response - V1 Ripple & Noise Overvoltage Protection Overload Protection Short Circuit Protection Temperature Coefficient Overtemperature Protection 1% 115 110 0.02 %/˚C °C Notes & Conditions See Models and Ratings table 50% load, 115/230 VAC V1 only. See mechanical details. 230 VAC full load After 20 min warm up 90-264 VAC 0-100% load. Recovery within 1% in less than 500 µs for a 50-75% and 75-50% load step V1: 20 MHz bandwidth Vnom DC. Output 1 only, recycle input to reset Output 1 only, auto reset. See fig 2. Auto Recovery, hiccup mode Protects unit from overtemperature. Auto reset. Output Overload Characteristic Output Voltage (V) 14 12 10 8 6 4 Unit enters hiccup mode 2 0 0 5 10 15 20 25 30 35 Output Current (A) Figure 2 Typical V1 Overload Characteristic (SHP350PS12 shown) 3 xppower.com General Specifications Xxxxxxxxxx Characteristic Efficiency Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Power Density Minimum Typical 85 Maximum 3000 1500 500 70/200/130 6.6 Mean Time Between Failure Weight Units % VAC VAC VDC kHz W/in3 Notes & Conditions See fig 3 & 4 PFC converter / Main converter / Standby 216 kHrs MIL-HDBK-217F at 25 ºC GB 2.1 (940) lb (g) See mechanical details Efficiency vs Load SHP350PS12 Figure 3 90% 80% 70% Efficiency 60% 50% 115Vac input 40% 30% 230Vac input 20% 10% 0% 10 20 30 40 50 60 70 80 90 100 Load (%) SHP350PS48 Figure 4 90% 80% 70% Efficiency 60% 50% 115Vac input 40% 30% 230Vac input 20% 10% 0% 10 20 30 40 50 60 70 80 90 100 Load (%) Signals & Control Characteristic Notes & Conditions Signals & Control Remote Sense AC OK / Power Fail Remote On/Off (Inhibit/Enable) 4 Compensates for 0.5 V total voltage drop Open collector referenced to negative sense, transistor normally off when AC is good (see fig. 5 & 8) AC OK: Provides ≥ 5 ms warning of loss of output from AC failure Uncommited isolated optocoupler diode, powered diode inhibits both V1 & V2 (fan supply) (see fig.6 & 9) Current Share When more than one unit (with the same output voltage) is used in parallel to increase output current, the current share pins 5/6 of one unit should be connected to pins 5/6 of the other unit(s). This will force the current to share between the outputs. Similarly pins 2/4 of each unit should also be connected as a ground reference. Units share current within 10% of each other at full load. See fig 7. Standby Supply V2 Isolated 5 V/0.2 A supply, always present when AC supplied. xppower.com Signals & Control AC OK/Power Fail Figure 5 POWER SUPPLY 5 V Standby Pin 9 Max 12 V 20 mA 330R AC OK Collector Pin 3 Transistor On (4.5 V): AC OK AC OK Emitter Pin 2 (-sense) 5 V Standby Return Pin 10 J2 Logic Connector Remote On/Off (Inhibit) INHIBIT HI INHIBIT LOW Figure 6 800 R POWER SUPPLY 800 R 5 V Standby Pin 9 5 V Standby Pin 9 2-5 mA 100 R 2-5 mA Inhibit Hi Pin 7 On (4.5 V): 100 R Inhibit Hi Pin 7 Inhibit Lo Pin 8 Inhibit Lo Pin 8 5 V Standby Return Pin 10 5 V Standby Return Pin 10 Chassis J3 Logic Connector Signal POWER SUPPLY Chassis J3 Logic Connector High: Power Supply OFF Low or Floating: Power Supply ON Signal High: Power Supply ON Low or Floating: Power Supply OFF Signals - Parallel Load & Current Share Connection Example SHP350PSXX (1) V1 Output ns e V1 Output - Current Share s en -S e se en -S Figure 7 Se + + Sens + - + e Se ns e Current Share + + - Sense - SHP350PSXX (3) SHP350PSXX (2) V1 Output - + Load 5 xppower.com Parallel AC OK Connection Power Supply 1 5 V Standby Pin 9 330R AC OK Collector Pin 3 AC OK Emitter Pin 2 5 V Standby Return Pin 10 J3 Connector Power Supply 2 OK Collector Pin 3 Figure 8 OK Emitter Pin 2 J3 Connector Power Supply 3 AC OK Collector Pin 3 Transistor On (4.5 V): AC OK AC OK Emitter Pin 2 J3 Connector Parallel Remote Inhibit Connection PSU 1 Figure 9 6 PSU 8 PSU 2 Pin 7 Pin 7 Pin 7 Pin 8 Pin 8 Pin 8 Please see figure 6. xppower.com Environmental Characteristic Minimum Typical Maximum Units Operating Temperature -40 +70 °C Storage Temperature -40 +85 °C See derating curve, fig 10. Cooling 5 Humidity Operating Altitude 95 3000 Notes & Conditions %RH m Integral variable speed fan load dependant. See fig 11. Non-condensing 3 x 30 g/11 ms shocks in both +ve & -ve directions along the 3 orthogonal axis, total 18 shocks. EN60068-2-27 & EN60068-2-47. Single axis 10-500 Hz at 2 g x 10 sweeps. EN60068-2-6. Shock Vibration Temperature Derating Curve Figure 10 Some specification parameters may not be met Output Load (%) 100 50 0 -40 -20 0 +50 +70 Ambient Temperature (ºC) Fan Speed Control 100 Fan Speed (%) Figure 11 0 0 10 25 50 75 100 Output Power (%) Electromagnetic Compatibility - Immunity Phenomenon Low Voltage PSU EMC Harmonic Current ESD Radiated EFT Surges Conducted Dips and Interruptions Standard EN61204-3 EN61000-3-2 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-11 SEMI F47 Test Level High severity level Class A 3 3 3 Installation class 3 3 Dip: 20% 5000 ms Dip: 30% 500 ms Dip: 60% 200 ms Dip: 100% 5000 ms Criteria as below Notes & Conditions A A A A A A A B B Compliant 7 xppower.com Electromagnetic Compatibility - Emissions Phenomenon Test Level Standard EN55032 EN55032 EN61000-3-3 Conducted Radiated Voltage Fluctuations Notes & Conditions Criteria Class B Class A Safety Agency Approvals Safety Agency CB Report UL TUV CE Safety Standard IEC60950-1:2005 Ed 2 / IEC62368-1:2014 UL 62368-1 & CAN/CSA C22.2 No. 62368-1-14 EN62368-1:2014/A11:2017 LVD Equipment Protection Class Safety Standard Notes & Conditions IEC60950-1:2005 Ed 2 / IEC62368-1:2014 See safety agency conditions of acceptibility for details Class I Category Information Technology Information Technology Information Technology Mechanical Details Standard Terminal Block M4 Screw 4 Pins 0.37 (9.5) Centre Standard Terminal Block M3.5 Screw 3 Pins 0.37 (9.5) Centre 2.1 (53.34) L -VOUT N +VOUT LED 2.20 (55.9) B 1.13 (28.72) VR 1.03 (26.2) 0.06 (1.5) 7.00 (177.8) A Mounting Hole 8 places M3 x 0.5 0.15 (3.8) Max. Penetration PIN 2 PIN 1 PIN 10 PIN 9 A A AIRFLOW 1.61 (41.0) -2X DETAIL B SCALE 2 : 1 LOGIC CONNECTOR J3 A A 2.44 (62.0) CL A A 5.35 (136.0) Notes: 1. Dimensions shown in inches (mm). 2. Weight: 1.73 lb (0.788 kg). 8 3.6 (91.44) 0.70 (17.9) J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby 10 5 V Standby Return 3. Logic connector J3 mates with JST housing PHDR-10VS and SPHD-001T-P0.5 Crimp Terminals 18 Feb 20 SHP650 Series • Rugged Industrial Construction • End Fan, Top Fan & U’ ‘ Channel Mechanical Options • -40 °C to +70 °C Operation • 5 V Standby • AC OK, Remote On/Off and Active Current Share • Load Dependant Variable Fan Speed • Screw Terminals • SEMI F47 Compliant • 3 Year Warranty The SHP650 AC-DC power supply provides upto 650 W of output power in three mechanical packages to provide installation flexibility in a range of industrial applications. The unit comprises of a main output with voltages from 12-48 VDC and two peripheral outputs providing a 12 VDC fan supply and a 5 VDC standby supply which can be utilitsed with the signals and control features of the unit to provide detection of loss of AC input and remote on/off control. Multiple units can used in parallel via the current share facility, providing higher power solutions. Inherently low earth leakage current, and conducted EMC compliance to Class B also simplify higher power system design. Packaged in a compact 8” (203 mm) x 4” (102 mm) x 2.6” (65 mm) and carrying IEC60950 family safety approvals, the SHP650 has a load dependant variable speed fan is fully protected with overtemperature shutdown and provides full power from -20 ºC to 50 ºC and 50% power at +70 ºC. xppower.com Models and Ratings End Fan Models (-EF) Output Voltage V1 12 V 15 V 24 V 28 V 36 V 48 V Max Output Current V1 50.0 A 40.0 A 27.0 A 23.0 A 18.0 A 13.5 A Fan Supply V2 Not Not Not Not Not Not Standby Supply V3 Available Available Available Available Available Available 5V 5V 5V 5V 5V 5V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 Max Output Power Model Number 607 W 607 W 657 W 651 W 657 W 657 W SHP650PS12-EF SHP650PS15-EF SHP650PS24-EF SHP650PS28-EF SHP650PS36-EF SHP650PS48-EF A A A A A A Top Fan Models (-TF) Output Voltage V1 12 V 15 V 24 V 28 V 36 V 48 V Max Output Current V1 50.0 A 40.0 A 27.0 A 23.0 A 18.0 A 13.5 A Fan Supply V2 Not Not Not Not Not Not Standby Supply V3 Available Available Available Available Available Available 5V 5V 5V 5V 5V 5V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 Max Output Power Model Number 607 W 607 W 657 W 651 W 657 W 657 W SHP650PS12-TF SHP650PS15-TF SHP650PS24-TF SHP650PS28-TF SHP650PS36-TF SHP650PS48-TF Max Output Power(1) Model Number 601 W 601 W 651 W 655 W 651 W 651 W SHP650PS12 SHP650PS15 SHP650PS24 SHP650PS28 SHP650PS36 SHP650PS48 A A A A A A U Channel Models Output Voltage V1 12 V 15 V 24 V 28 V 36 V 48 V Max Output Current V1 50.0 A 40.0 A 27.0 A 23.0 A 18.0 A 13.5 A Fan Supply V2 12 V 12 V 12 V 12 V 12 V 12 V / / / / / / 0.5 0.5 0.5 0.5 0.5 0.5 Standby Supply V3 A A A A A A 5V 5V 5V 5V 5V 5V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 A A A A A A 1. U Channel models require a minimum of 5.5 m/s airflow from the system for cooling Input Characteristics Characteristic Input Voltage - Operating Input Frequency Minimum 85 47 Typical 115/230 50/60 Units VAC Hz 40 0.75 A A A mA >0.9 Power Factor Input Current - No Load Input Current - Full Load Inrush Current Earth Leakage Current Input Protection Maximum 264 63 0.15/0.3 6.5/3.2 0.3/0.5 T16 A / 250 V internal in-line fuse Input Derating Curve Notes & Conditions Derate output power < 90 VAC. See fig. 1. Agency approval, 47-63 Hz EN61000-3-2 class A compliant EN61000-3-2 class C for loads ≥10% 115/230 VAC 115/230 VAC 230 VAC cold start, 25 ºC 115/230 VAC/50 Hz (Typ.), 264 VAC/60 Hz (Max.) 100 Figure 1 Output Power (%) 90 80 70 60 50 40 85 90 264 Input Voltage (VAC) 2 xppower.com Output Characteristics Characteristic Output Voltage - V1 Initial Set Accuracy Output Voltage Adjustment Minimum Load Start Up Delay Hold Up Time Drift Line Regulation Load Regulation Minimum 12 Typical ±0.2 ±0.5 ±1 (V1) , ±5 (V3) Units VDC % % A s ms % % % 4 % 1 140 145 % pk-pk % % I nom 0.02 %/˚C °C 0 0.5 20 Transient Response - V1 Ripple & Noise Overvoltage Protection Overload Protection Short Circuit Protection Temperature Coefficient Overtemperature Protection Maximum 48 ±1 (V1) , ±5 (V3) ±10 115 110 Notes & Conditions See Models and Ratings table 50% load, 115/230 VAC V1 only. See mechanical details. 230 VAC full load After 20 min warm up 90-264 VAC 0-100% load. Recovery within 1% in less than 500 µs for a 50-75% and 75-50% load step V1: 20 MHz bandwidth Vnom DC. Output 1 only, recycle input to reset Output 1 only, auto reset. See fig 2. Auto Recovery, hiccup mode Protects unit from overtemperature. Auto reset. Output Overload Characteristic Unit enters hiccup mode Figure 2 Typical V1 Overload Characteristic (SHP650PS12 shown) 3 xppower.com General Specifications Xxxxxxxxxx Characteristic Efficiency Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Power Density Minimum Typical 84 Maximum 3000 1500 500 70/200 8.2 Mean Time Between Failure 260 Weight Units % VAC VAC VDC kHz W/in3 kHrs 2.8 (1.25) lb (kg) Notes & Conditions See fig 3 & 4 PFC converter / Main converter MIL-HDBK-217F at 25 ºC GB See mechanical details Efficiency vs Load SHP650PS12 Figure 3 SHP650PS48 Figure 4 Signals & Control Characteristic Notes & Conditions Signals & Control Remote Sense AC OK / Power Fail Remote On/Off (Inhibit/Enable) 4 Compensates for 0.5 V total voltage drop Open collector referenced to negative sense, transistor normally off when AC is good (see fig. 5 & 8) AC OK: Provides ≥ 5 ms warning of loss of output from AC failure Uncommited isolated optocoupler diode, powered diode inhibits both V1 & V2 (fan supply) (see fig.6 & 9) Current Share When more than one unit (with the same output voltage) is used in parallel to increase output current, the current share pins 5/6 of one unit should be connected to pins 5/6 of the other unit(s). This will force the current to share between the outputs. Similarly pins 2/4 of each unit should also be connected as a ground reference. Units share current within 10% of each other at full load. See fig 7. Standby Supply V3 Isolated 5 V/0.2 A supply, always present when AC supplied. xppower.com Signals & Control AC OK/Power Fail Figure 5 POWER SUPPLY 5 V Standby Pin 9 Max 12 V 20 mA 330R AC OK Collector Pin 3 Transistor On (4.5 V): AC OK AC OK Emitter Pin 2 (-sense) 5 V Standby Return Pin 10 J3 Logic Connector Remote On/Off (Inhibit) Figure 6 INHIBIT HI INHIBIT LOW 800 R POWER SUPPLY 800 R 5 V Standby Pin 9 5 V Standby Pin 9 2-5 mA 100 R 2-5 mA Inhibit Hi Pin 7 POWER SUPPLY 100 R Inhibit Hi Pin 7 4.5 V): Inhibit Lo Pin 8 Inhibit Lo Pin 8 5 V Standby Return Pin 10 5 V Standby Return Pin 10 Chassis J3 Logic Connector Signal Chassis J3 Logic Connector High: Power Supply OFF Low or Floating: Power Supply ON Signal High: Power Supply ON Low or Floating: Power Supply OFF Signals - Parallel Load & Current Share Connection Example SHP650PSXX (2) V1 Output V1 Output Current Share Figure 7 se en -S ns e e Se + + Sens + - V1 Output - Current Share -S s en + e + + - Sense - SHP650PSXX (3) Se ns e SHP650PSXX (1) - + Load 5 xppower.com Parallel AC OK Connection Power Supply 1 5 V Standby Pin 9 330R AC OK Collector Pin 3 AC OK Emitter Pin 2 5 V Standby Return Pin 10 J3 Connector Power Supply 2 OK Collector Pin 3 Figure 8 OK Emitter Pin 2 J3 Connector Power Supply 3 AC OK Collector Pin 3 Transistor On (4.5 V): AC OK AC OK Emitter Pin 2 J3 Connector Parallel Remote Inhibit Connection PSU 1 Figure 9 6 PSU 8 PSU 2 Pin 7 Pin 7 Pin 7 Pin 8 Pin 8 Pin 8 Please see figure 6. xppower.com Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +70 °C See derating curve, fig 10. Storage Temperature -40 +85 °C Some specification parameters maybe exceeded until after 20 minutes warm up period. Cooling Humidity Operating Altitude 5 95 3000 %RH m Integral variable speed fan load dependant. See fig 11. Non-condensing Shock 3 x 30 g/11 ms shocks in both +ve & -ve directions along the 3 orthogonal axis, total 18 shocks. Vibration Single axis 10-500 Hz at 2 g x 10 sweeps Temperature Derating Curve Figure 10 Some specification parameters may not be met Output Load (%) 100 50 0 -40 -20 0 +50 +70 Ambient Temperature (ºC) Fan Speed Control Figure 11 Fan Speed (%) 100 50 0 0 25 50 75 100 Output Power (%) Electromagnetic Compatibility - Immunity Phenomenon Low Voltage PSU EMC Standard EN61204-3 Harmonic Current EN61000-3-2 ESD Radiated EFT Surges Conducted EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Dips and Interruptions EN61000-4-11 SEMI F47 Test Level High severity level Class A Class C 3 3 3 Installation class 3 3 Dip: 30% 10 ms Dip: 60% 100 ms Dip: 100% 5000 ms Criteria as below Notes & Conditions For loads ≥10% A A A A A A B B Compliant 7 xppower.com Electromagnetic Compatibility - Emissions Phenomenon Test Level Standard EN55032 EN55032 EN61000-3-3 Conducted Radiated Voltage Fluctuations Notes & Conditions Criteria Class B Class A Safety Agency Approvals Safety Agency CB Report UL TUV CE Safety Standard IEC60950-1:2005 Ed 2 / IEC62368-1:2014 UL 62368-1 & CAN/CSA C22.2 No. 62368-1-14 EN62368-1:2014/A11:2017 LVD Equipment Protection Class Safety Standard Notes & Conditions IEC60950-1:2005 Ed 2 / IEC62368-1:2014 See safety agency conditions of acceptibility for details Class I Category Information Technology Information Technology Information Technology Mechanical Details - End Fan (Suffix -EF) Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Vo+ L E N Vo- Standard Terminal Block, M3.5 Screw 3 Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) 2.49 (63.3) V1 Adjustment Output On, LED 9.18 (233.2) 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 2.50 (63.5) AIRFLOW Pin 2 Pin 1 Pin 10 Pin 9 1.95 (49.5) J3: Logic Connector 8.00 (203.2) 2.86 (72.6) 4.00 (101.6) CL 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) Notes: 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.25 kg). 8 6.53 (165.8) 0.87 (22.2) J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby (V3) 10 5 V Standby Return (V3) 3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. xppower.com Xxxxxxxxxx Details - Top Fan (Suffix -TF) Mechanical Standard Terminal Block, M3.5 Screw 3, Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Vo+ L E Vo- N V1 Adjustment Output On, LED 2.50 (63.5) 8.00 (203.2) 2.58 (65.5) AIRFLOW 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 1.95 (49.5) Pin 2 Pin 1 Pin 10 pin 9 J3: Logic Connector 2.86 (72.6) 4.00 (101.6) 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) Pin 1 2 3 4 5 6 7 8 9 10 Notes: 1. Dimensions shown in inches (mm). 2. Weight: 2.6 lb (1.2 kg). 0.87 (22.2) 6.53 (165.8) J3 Logic Connector (JST B10B-PHDSS) Function + Sense - Sense AC OK/Power Fail - Sense Current Share Current Share + Inhibit - Inhibit +5 V Standby (V3) 5 V Standby Return (V3) 3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. 9 xppower.com Xxxxxxxxxx Details - U Channel (No Suffix) Mechanical Standard Terminal Block M3.5 Screw 3 Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Standard Terminal Block, M4 Screw 6 Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Vo+ L E Vo- N V1 Adjustment Output On, LED 8.00 (203.2) 2.46 (62.5) 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) System Airflow Required Pin 2 Pin 1 Pin 10 Pin 9 1.95 (49.5) J3: Logic Connector Pin 1 J1: Fan Connector 4.00 (101.6) CL 2.86 (72.6) 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) Notes: 1. Dimensions shown in inches (mm). 2. Weight: 2.4 lb (1.1 kg). 3. Requires system airflow, see thermal considerations. 6.53 (165.80) 0.87 (22.2) 4. J3 Mating plug: JST part no. PHR-2, contact: JST part no. SPH-002T-P0.5S. 5. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby (V3) 10 5 V Standby Return (V3) J1 Fan Connector (JST B2B-PH-KL (LF) (SN) Pin Function 1 +V 2 NC 3 -V Thermal Considerations (U Channel) Temperature Measurements (Ambient ≤50 °C) Recommended Maximum Temperature °C Temperature °C C55 Capacitor 70 105 T302 Transformer 90 120 C314 Capacitor 70 105 D311 Diode 100 120 Component 10 In order to ensure reliable operation in the end use application the recommended component temperatures listed should not be exceeded. Higher temperatures up to the maximum stated can be used but product lifetime may be reduced. 18 Feb 20 SHP1000 Series • 1200 W High Line Output Power • Rugged Industrial Construction • Variable Speed Fan for Noise Reduction • -40 °C to +70 °C Operation • 5 V Standby • AC OK, Remote On/Off and Active Current Share • Screw Terminals • 3 Year Warranty ­The­SHP1000­AC-DC­power­supply­provides­up­to­1200­W­of­output­power­in­a­compact­rugged­mechanical­package,­suitable­for­a range­of­industrial­applications. The­unit­comprises­of­a­main­output­with­voltages­from­12-48­VDC­and­a­5­VDC­standby­supply­which­can­be­utilitsed­with­the signals­and­control­features­of­the­unit­to­provide­detection­of­loss­of­AC­input­and­remote­on/off­control. Multiple­units­can­be­used­in­parallel­via­the­current­share­facility,­providing­higher­power­solutions.­Inherently­low­earth­leakage current,­and­conducted­EMC­compliance­to­Class­B­also­simplify­higher­power­system­design. Packaged­in­a­compact­9.5”­(241­mm)­x­5.9”­(150­mm)­x­2.4”­(61­mm)­and­carrying­IEC60950­family­safety­approvals,­the­SHP1000 has­a­load­dependant­variable­speed­fan­is­fully­protected­with­overtemperature­shutdown­and­provides­-40­ºC­start­up­with­full power­from­-20­ºC­to­50­ºC­and­50%­power­at­+70­ºC.­ xppower.com Models and Ratings Output Voltage V1 Max Output Current V1 180 VAC 83.0 A 67.0 A 42.0 36.0 28.0 21.0 A A A A 50.0 42.9 33.3 25.0 A A A A Max Output Power Standby Supply V2 5V 5V 5V 5V 5V 5V / / / / / / 1.0 1.0 1.0 1.0 1.0 1.0 180 VAC 1001 W 1010 W 1013 W 1013 W 1013 W 1013 W 1205 W 1206 W 1204 W 1205 W Model Number SHP1000PS12 SHP1000PS15 SHP1000PS24 SHP1000PS28 SHP1000PS36 SHP1000PS48 Input Characteristics Characteristic Input Voltage - Operating Input Frequency Minimum 85 47 Typical 115/230 50/60 Units VAC Hz >0.9 Power Factor Input Current - No Load Input Current - Full Load (1000 W) Inrush Current Earth Leakage Current Input Protection Maximum 264 63 EN61000-3-2 class A compliant 0.35/0.5 A 115/230 VAC 10.9/5.3 A 115/230 VAC A µA 230 VAC cold start, 25 ºC 115/230 VAC/50 Hz (Typ.), 264 VAC/60 Hz (Max.) 60 75/140 250 T20 A/250 V internal fuse in both lines Input Derating Curve Notes & Conditions Derate output power < 90 VAC. See fig. 1. 100 Figure 1 Output Power (%) 90 80 70 60 50 40 85 90 264 Input Voltage (VAC) 2 xppower.com Output Characteristics Characteristic Output Voltage - V1 Initial Set Accuracy Output Voltage Adjustment Minimum Load Start Up Delay Hold Up Time Drift Line Regulation Load Regulation Minimum 12 Typical Maximum 48 ±1 (V1) , ±5 (V2) ±10 ±0.2 ±0.5 ±1 (V1) , ±5 (V2) Units VDC % % A s ms % % % 4 % 1 145 140 % pk-pk % % I nom 0.02 %/˚C °C 0 0.5 20 Transient Response - V1 Ripple & Noise Overvoltage Protection Overload Protection Short Circuit Protection Temperature Coefficient Overtemperature Protection 115 110 Notes & Conditions See Models and Ratings table 50% load, 115/230 VAC V1 only. See mechanical details. 230 VAC full load After 20 min warm up 90-264 VAC 0-100% load. Recovery within 1% in less than 500 µs for a 50-75% and 75-50% load step V1: 20 MHz bandwidth Vnom DC. Output 1 only, recycle input to reset Output 1 only, auto reset. See fig 2. Auto Recovery, hiccup mode Protects unit from overtemperature. Auto reset. Output Overload Characteristic Output Voltage (V) 14 12 10 8 6 4 Unit enters hiccup mode 2 0 0 30 40 50 60 70 80 90 Output Current (A) Figure 2 Typical V1 Overload Characteristic (SHP1000PS12 shown) 3 xppower.com General Specifications Xxxxxxxxxx Characteristic Efficiency Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Power Density Mean Time Between Failure Weight Minimum Typical 84 Maximum 3000 1500 500 70/200/130 8.9 Units % VAC VAC VDC kHz W/in3 Notes & Conditions See fig 3 & 4 PFC converter / Main converter / Standby 275 kHrs MIL-HDBK-217F at 25 ºC GB 2.1 (940) lb (g) See mechanical details Efficiency vs Load SHP1000PS12 Figure 3 SHP1000PS48 Figure 4 Signals & Control Characteristic Notes & Conditions Signals & Control Remote Sense AC OK / Power Fail Remote On/Off (Inhibit/Enable) 4 Compensates for 0.5 V total voltage drop Open collector referenced to negative sense, transistor normally off when AC is good (see fig. 5 & 8) AC OK: Provides ≥ 5 ms warning of loss of output from AC failure Uncommited isolated optocoupler diode, powered diode inhibits both V1 & V2 (fan supply) (see fig.6 & 9) Current Share When more than one unit (with the same output voltage) is used in parallel to increase output current, the current share pins 5/6 of one unit should be connected to pins 5/6 of the other unit(s). This will force the current to share between the outputs. Similarly pins 2/4 of each unit should also be connected as a ground reference. Units share current within 10% of each other at full load. See fig 7. Standby Supply V2 Isolated 5 V/1.0 A supply, always present when AC supplied. xppower.com Signals & Control AC OK/Power Fail Figure 5 POWER SUPPLY 5 V Standby Pin 9 Max 12 V 20 mA 330R AC OK Collector Pin 3 Transistor On (4.5 V): AC OK AC OK Emitter Pin 2 (-sense) 5 V Standby Return Pin 10 J2 Logic Connector Remote On/Off (Inhibit) INHIBIT HI INHIBIT LOW Figure 6 800 R POWER SUPPLY 800 R 5 V Standby Pin 9 5 V Standby Pin 9 2-5 mA 100 R 2-5 mA Inhibit Hi Pin 7 On (4.5 V): 100 R Inhibit Hi Pin 7 Inhibit Lo Pin 8 Inhibit Lo Pin 8 5 V Standby Return Pin 10 5 V Standby Return Pin 10 Chassis J3 Logic Connector Signal POWER SUPPLY Chassis J3 Logic Connector High: Power Supply OFF Low or Floating: Power Supply ON Signal High: Power Supply ON Low or Floating: Power Supply OFF Signals - Parallel Load & Current Share Connection Example SHP1000PSXX (1) V1 Output ns e V1 Output - Current Share s en -S e se en -S Figure 7 Se + + Sens + - + e Se ns e Current Share + + - Sense - SHP1000PSXX (3) SHP1000PSXX (2) V1 Output - + Load 5 xppower.com Parallel AC OK Connection Power Supply 1 5 V Standby Pin 9 330R AC OK Collector Pin 3 AC OK Emitter Pin 2 5 V Standby Return Pin 10 J3 Connector Power Supply 2 OK Collector Pin 3 Figure 8 OK Emitter Pin 2 J3 Connector Power Supply 3 AC OK Collector Pin 3 Transistor On (4.5 V): AC OK AC OK Emitter Pin 2 J3 Connector Parallel Remote Inhibit Connection PSU 1 Figure 9 6 PSU 8 PSU 2 Pin 7 Pin 7 Pin 7 Pin 8 Pin 8 Pin 8 Please see figure 6. xppower.com Environmental Characteristic Minimum Typical Maximum Units Operating Temperature -40 +70 °C Storage Temperature -40 +85 °C Notes & Conditions See derating curve, fig 10. 2 x integral variable speed fans load dependant. See fig 11. Non-condensing Cooling Humidity Operating Altitude 5 95 3000 %RH m Shock 3 x 30 g/11 ms shocks in both +ve & -ve directions along the 3 orthogonal axis, total 18 shocks. Vibration Single axis 10-500 Hz at 2 g x 10 sweeps Temperature Derating Curve Figure 10 Some specification parameters may not be met Output Load (%) 100 50 0 -40 -20 0 +50 +70 Ambient Temperature (ºC) Fan Speed Control 100 Fan Speed (%) Figure 11 0 0 10 25 50 75 100 Output Power (%) Electromagnetic Compatibility - Immunity Phenomenon Low Voltage PSU EMC Standard EN61204-3 Test Level High severity level Harmonic Current EN61000-3-2 Class A ESD EN61000-4-2 3 A Radiated EN61000-4-3 3 A EFT EN61000-4-4 3 A Surges EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 3 A EN61000-4-11 Dips and Interruptions SEMI F47 Criteria as below Dip: 20% 5000 ms A Dip: 30% 500 ms A Dip: 60% 200 ms B Dip: 100% 5000 ms B Notes & Conditions Compliant 7 xppower.com Electromagnetic Compatibility - Emissions Phenomenon Standard EN55032 EN55032 EN61000-3-3 Conducted Radiated Voltage Fluctuations Test Level Notes & Conditions Criteria Class B Class A Safety Agency Approvals Safety Agency CB Report UL TUV CE Safety Standard IEC60950-1:2005 Ed 2 / IEC62368-1:2014 UL 62368-1 & CAN/CSA C22.2 No. 62368-1-14 EN62368-1:2014/A11:2017 LVD Equipment Protection Class Safety Standard Notes & Conditions IEC60950-1:2005 Ed 2 See safety agency conditions of acceptibility for details Class I Category Information Technology Information Technology Information Technology Mechanical Details VO+ VO- Standard Terminal Block, M6 Screw, 4 Pins 0.62 (16.0) center Torque 26.0 lbs-in (2.94 Nm) 5.90 (149.8) 2.91 (73.9) Output On, LED A V1 Adjustment N 1.47 (37.4) L 2.40 (61.0) 9.48 (240.9) 1.20 (30.5) 9.55 (242.64) Standard Terminal Block, M4 Screw 3 Pins 0.37 (9.5) center Torque 10.62 lbs-in (1.2 Nm) 9.41 (238.9) 4 x M4-0.7 THD both side faces 0.15 (3.8) max screw penetration max torque 10.62 lbs-in (1.2 Nm) B B Airflow 1.20 (30.5) 4 x M4-0.7 THD both side faces 0.15 (3.8) max screw penetration max torque 10.62 lbs-in (1.2 Nm) B B 4.50 (114.3) CL Pin 2 Pin 1 Pin 10 Pin 9 B J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby 10 -5 V Standby B Detail A J3: Logic Connector 6.70 (170.2) 1.33 (33.8) Notes: 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.25 kg). 8 3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. 18 Feb 20