SMP350PS28

SMP350 Series AC-DC Power Supplies 350 Watts • Rugged Industrial Construction • -40 °C to +70 °C Operation • Screw Terminals • High Efficiency • Remote On/Off • Low Leakage Current • Class B Emissions • 3 Year Warranty The SMP350 series provides a range of rugged, enclosed, 300 – 350W supplies with integral fan, screw terminal connections and a wide operating temperature range of -40 °C to +70 °C ideally suited to a wide range of industrial applications. The SMP350 series features high efficiency and class B EMI emissions for ease of integration into the end application and offers remote On/Off to simplify system control. Packaged in a 3.6” x 7” x 1.7” enclosure the series offers power densities up to 13 W/in3 providing a compact, high efficiency, low noise power solution. Dimensions: SMP350: 3.6 x 7.0 x 1.7” (91.4 x 177.8 x 43.1 mm) Models & Ratings Output Voltage V1 12.0 VDC 15.0 VDC 18.0 VDC 24.0 VDC 28.0 VDC 36.0 VDC 48.0 VDC 90-180 VAC Output Current Output Power 25.00 A 300 W 20.70 A 310 W 17.80 A 320 W 13.75 A 330 W 11.80 A 330 W 9.20 A 330 W 7.30 A 350 W 180-264 VAC Output Current Output Power 25.00 A 300 W 22.00 A 330 W 19.40 A 350 W 14.60 A 350 W 12.50 A 350 W 9.70 A 350 W 7.30 A 350 W Model Number(1) SMP350PS12 SMP350PS15 SMP350PS18 SMP350PS24 SMP350PS28 SMP350PS36 SMP350PS48 Notes 1. For reduced leakage current medical versions (125 W 90 VAC, 100% load 115 VAC/230 VAC when inhibited 230 VAC, cold start 25 °C 264 VAC/60 Hz. For reduced leakage current medical versions (4 % 150 140 % % Trip and Restart Cycle AC to reset Thermal protection fitted %/°C s % After 20 minute warm up 115/230 VAC, full load 4 V to switch on 0.02 1 5 General Characteristic Efficiency Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Mean Time Between Failure Power Density Weight Minimum Typical Maximum Units Notes & Conditions 87 4000 1500 1500 60 90 90 93 % VAC VAC VAC See figures 2 – 4 below 2 x MOPP 1 x MOPP 1 x MOPP PFC Main Converter MIL-HDBK-217F, notice 2, +25 °C GB 200 150 kHz 13 kHrs W/in3 lb (kg) 570 1.5 (0.68) www.xppower.com 2 SMP350 Series AC-DC Power Supplies Efficiency Vs Load Figure 2 100 12 V Models Efficincy E (%) 95 115VAC 90 230VAC 85 7 80 75 70 25 50 75 100 Load (%) Figure 3 100 24 V Models Efficiency (%) 95 90 115VAC 85 230VAC 80 1 75 70 25 50 7 Figure 4 100 L 100 48 V Models 75 Load (%) Efficiency (%) 95 90 85 115VAC 80 230VAC 1 75 70 25 50 75 100 Load (%) Environmental Characteristic 3 Minimum Typical Maximum Units Operating Temperature -40 +70 °C °C Notes & Conditions Derate linearly above 50 °C to 50% of rated power at 70 °C, see fig 5 Storage Temperature -40 +85 Operating Humidity 5 95 % RH, non-condensing Storage Humidity 5 95 % RH, non-condensing Shock ±3 x 30 g shocks in each plane, total 18 shocks. 30 g = 11 ms (±0.5 ms), half sine. Conforms to EN60068-2-27 & EN60068-2-47 Vibration Single axis 10-500 Hz at 2 g sweep and endurance at resonance in all 3 plans. Conforms to EN60068-2-6 www.xppower.com SMP350 Series AC-DC Power Supplies Thermal Derating Curve Figure 5 50 0 -40 Some specification parameters may not be met Output Load (%) 100 -20 0 50 Ambient Temperature (ºC) 70 Signals & Controls Notes & Conditions Characteristic Remote Sense Compensates for 0.5 V total voltage drop Inhibit Remote On/Off (-R models) (Standard on GCS350 models) Enable The inhibit lo (pin 4), should be pulled below 0.4 V to switch V1 & Vfan off. Open circuit or >4 V to switch on (see fig. 6) With the inhibit lo (pin 4) pulled low as detailed above, connecting inhibit hi (pin 5) to inhibit lo (pin 4) will enable V1 & V fan output. (see fig. 7) Remote On/Off (Inhibit) Remote On/Off (Enable) Figure 6 Figure 7 POWER SUPPLY POWER SUPPLY Inhibit Hi Pin 5 Inhibit Lo Pin 4 Inhibit Lo Pin 4 0V 0V Signals Connector Signals Connector 44 P www.xppower.com SMP350 Series AC-DC Power Supplies EMC: Emissions Standard Test Level EN55011/32 Class B Radiated EN55011/32 Class A Harmonic Fluctuations EN61000-3-3 Phenomenon Conducted Criteria Notes & Conditions Notes & Conditions EMC: Immunity Phenomenon Low Voltage PSU EMC Standard Test Level Criteria EN61204-3 High severity level as below Class A All models Harmonic Current EN61000-3-3 Radiated EN61000-4-3 3 A EFT EN61000-4-4 3 A Surges EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 3 Dip 100% (0 VAC), 8.4ms Dip 100% (0 VAC), 16.7ms A A B EN61000-4-11 (100 VAC) Dip 60% (40 VAC), 200ms B Dip 30% (70 VAC), 500ms B Dip 20% (80 VAC), 5000ms B Int 100% (0 VAC), 5000ms B EN61000-4-11 (240 VAC) Dips and Interruptions EN60601-1-2 (100 VAC) EN60601-1-2 (240 VAC) SEMI F47 (100 VAC) Class C > 125 W Dip 100% (0 VAC), 10ms A Dip 100% (0 VAC), 20ms B Dip 60% (96 VAC), 200ms B Dip 30% (168 VAC), 500ms B Dip 20% (192 VAC), 5000ms B Int 100% (0 VAC), 5000ms B Dip 100% (0 VAC), 10ms A Dip 60% (40 VAC), 100ms A Dip 30% (70 VAC), 500ms A Int 100% (0 VAC), 5000ms B Dip 100% (0 VAC), 10ms A Dip 60% (96 VAC), 100ms A Dip 30% (168 VAC), 500ms A Int 100% (0 VAC), 5000ms B Dip 33% (70 VAC), 500ms A Derate Power to 150 W Safety Approvals Safety Agency CB Report UL TUV Notes & Conditions Information Technology IEC62368-1 Ed 2 Information Technology IEC60601-1 Ed 3 Including Risk Management Medical UL62368-1, CSA C22.2 No. 62368-1 Information Technology ANSI/AAMI ES60601-1:2005 & CSA C22.2, No.60601-1:08 Medical EN62368-1 Information Technology EN60601-1/2006 Medical CE LVD & RoHS Equipment Protection Class Class I See safety agency conditions of acceptibility for details Means of Protection Category Primary to Secondary 5 Safety Standard IEC60950-1:2005 Ed 2 2 x MOPP (Means of Patient Protection) Primary to Earth 1 x MOPP (Means of Patient Protection) Secondary to Earth 1 x MOPP (Means of Patient Protection) IEC60601-1 Ed 3 www.xppower.com SMP350 Series AC-DC Power Supplies Mechanical Details 0.12 (3.0) 7.0 (177.8) Terminal Block TB1 7 x M3 Screw 0.28 (7.1) 0.33 (8.4) 3.6 (91.4) Voltage Adjust 0.59 (15.0) 0.32 (8.1) 2 x M3 x 0.5 THD 0.16 (4.0) max screw penetration 1.70 (43.2) 1.09 (27.6) 1.20 (30.5) 0.58 (14.7) 5.35 (135.9) 1.20 (30.5) 5.35 (135.9) 2 x M3 x 0.5 THD 0.16 (4.0) max screw penetration 2.44 (62.0) Notes 1. All dimensions in inches (mm). 2. Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25) 3. Weight: 1.5 lbs (0.68 kg) 4. J4 mates with JST Housing Pn. PHDR-10VS and with JST SPHD-001T-P0.5 crimp terminals. 66 www.xppower.com Terminal Block TB1 Pin Function 1 Line 2 Neutral 3 Ground 4 +V1 5 +V1 6 -V 7 -V Signal Connector J4 JST PN B10B-PHDSS Pin Function 1 +Sense 2 -Sense 3 XP Internal Use 4 Inhibit LO 5 Inhibit HI 6 N/C 7 N/C 8 N/C 9 N/C 10 N/C 02 Oct 17