UCP225PS24

UCP225 Series 225W AC-DC POWER SUPPLIES CONVECTION COOLED The UCP225 series is designed to minimize the no load power consumption and maximize efficiency to facilitate equipment design to meet the latest environmental legislation. Approved for medical and ITE applications, this range of single output AC/DC power supplies are packaged in an ultra-low profile 1.18” height with a foot print of just 3.12” by 5.0”. The UCP225 provides up to 225W force-cooled or 150W convection-cooled leading to very high power densities of 12.2W/in3 or 8.1W/in3 respectively. A 12V, 500mA fan supply is included in the design which can also be delivered with an optional 5V/2A standby output. The power supply contains two fuses and low leakage currents as required by medical applications and is safety approved to operate in a 70°C ambient. The low profile and safety approvals covering ITE and medical standards along with conducted emissions to EN55011/32 level B allow the Applications versatile UCP225 series to be used in a vast range of applications. Features • Low 1.18” Profile U Channel Construction Healthcare Home Healthcare Industrial Electronics Instrumentation Security Technology • -40°C to +70°C Operation • 3.12” by 5.0” Footprint • 150W Convection/225W Forced Cooled Ratings • Optional 5V Standby and Remote On/Off Dimensions • 12V Fan Output • Medical and ITE Approvals UCP225: • High Efficiency, up to 95% 5.00 x 3.12 x 1.18” (127.0 x 79.2 x 29.2 mm) • Less than 0.5W No Load Input Power Models & Ratings Model Number(3,4,5,6) Output Voltage Output Current Optional Standby Output Convection-cooled Forced-cooled(1) Convection-cooled Forced-cooled(1) Fan Output(7,8) Efficiency(2) UCP225PS12 12V 12.50A 18.75A 5V/1.0A 5V/2.0A 12V/0.5A 92% UCP225PS15 15V 10.00A 15.00A 5V/1.0A 5V/2.0A 12V/0.5A 92% UCP225PS18 18V 8.33A 12.50A 5V/1.0A 5V/2.0A 12V/0.5A 92% UCP225PS24 24V 6.25A 9.38A 5V/1.0A 5V/2.0A 12V/0.5A 92% UCP225PS28 28V 5.36A 8.04A 5V/1.0A 5V/2.0A 12V/0.5A 92% UCP225PS36 36V 4.16A 6.25A 5V/1.0A 5V/2.0A 12V/0.5A 92% UCP225PS48 48V 3.10A 4.69A 5V/1.0A 5V/2.0A 12V/0.5A 92% Notes: 1. Requires 10CFM or optional top fan cover, -TF 2. Minimum average efficiencies measured at 25%, 50%, 75% & 100% of 225 W load and 230 VAC input 3. Add suffix -T for input and output screw terminals e.g. UCP225PS24-T 4. Add suffix -TF for fan cover version e.g. UCP225PS24-TF 5. Add suffix -C for vented cover version e.g. UCP225PS24-C 6. Add suffix -A for optional 5V, 2A standby and remote on/off e.g. UCP225PS24-A 7. Typical voltage, actual regulated voltage will be in range of 10.5V to 11.1V 8. Regulation of the fan output requires a minimum load of 10W on the main output. UCP225 Series AC-DC POWER SUPPLIES Summary Characteristic Input Voltage Range Minimum Typical Maximum Units Notes & Conditions 85 115/230 264 VAC Derate from 100% at 90VAC to 90% at 85VAC 0.5 No Load Input Power W 94 Efficiency -40 Operating Temperature +70 % Model dependent °C -40°C for 150 W load, -25°C for 225W load, see derating curve EMC EN55011/32 Level B Conducted & Level A Radiated, EN61000-3-2, EN61000-3-3 Safety Approvals IEC62368-1, IEC60601-1, UL62368-1, EN60601-1 Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage - Operating 85 115/230 264 VAC Derate output from 100% at 90VAC to 90% at 85VAC Input Frequency 47 50/60 63 Hz >0.9 Power Factor Input Current - Full Load Inrush Current 2.2/1.1 A 115/230VAC 120 A 230VAC, cold start 25°C 80/140 Earth Leakage Current 230VAC, 100% load. EN61000-3-2 class A, class C >145W No Load Input Power 230 μA 0.5 W When main input is inhibited F3.15 A/250 V Internal fuse fitted in line and neutral Input Protection Output - Main Output Characteristic Output Voltage - V1 Minimum Typical 12 Initial Set Accuracy Minimum Load Maximum Units Notes & Conditions 48 VDC See Models & Ratings table ±1 % 50% load, 115/230VAC A No minimum load required s 115/230VAC, full load 0 2 Start Up Delay ms Minimum at full load, 115VAC. Typical at 150W/225W Drift ±0.02 % After 20 min warm up Line Regulation ±0.5 % 90-264VAC Load Regulation ±0.5 % 0-100% load 4 % Recovery within 1% in less than 500μs for a 50-75% and 75-50% load step 9 % Full load 1 % pk-pk Hold Up Time 10 20/13 Transient Response 5 Over/Undershoot Ripple & Noise Overvoltage Protection 110 140 % Overload Protection 110 175 % I nom 0.02 %/°C Overtemperature Protection Vnom, recycle input to reset Trip & restart Short Circuit Protection Temperature Coefficient 20MHz bandwidth and 10μF electrolytic capacitator in parallel with 0.1μF ceramic capacitator Measured internally, auto resetting 2 UCP225 Series AC-DC POWER SUPPLIES Output - Optional 5 V Standby Output Characteristic Minimum Typical Maximum 5.0 Output Voltage 0 Minimum Load 0.5 Start Up Delay 300 Hold Up Time Notes & Conditions VDC ±1 Initial Set Accuracy Units % 50% load, 115/230VAC A No minimum load required s 115/230VAC, full load ms Minimum at full load, 115VAC. Typical at 150W/225W Drift ±0.02 % After 20 min warm up Line Regulation ±0.5 % 90-264VAC Load Regulation ±0.5 % 0-100% load Transient Response 4 % Recovery within 1% in less than 500μs for a 50-75% and 75-50% load step Over/Undershoot 5 % Full load 1.2 % pk-pk 4.0 A 0.02 %/°C Ripple & Noise 2.4 Overload Protection 20MHz bandwidth and 10μF electrolytic capacitator in parallel with 0.1μF ceramic capacitator Trip & restart Short Circuit Protection Temperature Coefficient Connect pin 3 of CN2 to pin 1 to turn main output off. Connect to pin 2 or leave open to turn main output on Remote On/Off General Characteristic Minimum Typical Maximum 94 Efficiency Units % Notes & Conditions Model dependent Isolation: Input to Output 4000 VAC 2 x MOPP Input to Ground 1500 VAC 1 x MOPP Output to Ground 1500 40 Switching Frequency 50 VAC 1 x MOPP 130 kHz PFC 80 kHz Main converter kHz For optional standby output 65 12.2/8.1 W/in Forced/convection-cooled 300 khrs MIL-HDBK-217F, Notice 2 +25°C GB 0.71 (320) lb (g) For U channel version Power Density Mean Time Between Failure Weight 3 Specifications subject to change without notice. 3 Efficienc Convecon-cooled UCP225 Series Forced-cooled 115VAC input 85% 230VAC input 80% 75% 70% 100% 10 20 30 40 50 60 80 90 100 AC-DC POWER SUPPLIES 70 Load (%) 95% 90% Efficiency Efficiency Graphs Forced-cooled 115VAC input 230VAC input Efficiency Efficiency Convecon-cooled 10 20 30 40 50 60 70 80 90 70% 100 100% 115VAC input 230VAC input 20 Efficiency 30 40 50 60 70 Load (%) Convecon-cooled 80 90 95% 70% 100 Forced-cooled 90% 115VAC input 230VAC input Efficiency 10 Efficiency 115VAC input 230VAC input 20 30 40 50 60 70 80 90 100 Convecon-cooled Forced-cooled 115VAC input 230VAC input 10 20 30 40 Convecon-cooled 50 60 70 80 90 100 Forced-cooled Load (%) 115VAC input 230VAC input 80% 30 40 50 60 70 80 90 100% 100 Convecon-cooled Forced-cooled 115VAC input 85% 10 20 Figure 4 95% UCP225PS24-A 90% Load (%) 230VAC input Efficiency 20 30 40 50 60 70 80 90 100 Load (%) Convecon-cooled Forced-cooled 115VAC input 85% 230VAC input 80% 80% 75% 100% 100% 75% 70% 95% 10 20 30 40 50 Convecon-cooled 60 70 80 90 100 Forced-cooled Load (%) 85% 10 20 90% 115VAC input 230VAC input 80% Efficiency Efficiency 100 85% 70% 10 90% 30 40 Convecon-cooled 85% 50 60 70 Load (%) 80 90 100 Forced-cooled 115VAC input 230VAC input 80% 75% 75% 10 20 30 40 50 60 70 80 90 70% 100 100% Load (%) 95% 10 20 30 40 50 60 70 80 90 100 Load (%) 95% Convecon-cooled 90% Forced-cooled 115VAC input 85% 230VAC input 80% 75% 100% Efficiency 90% Efficiency 90 75% Figure 3 95% UCP225PS24 10 20 85% Characteristic 30 40 Convecon-cooled 50 60 70 Load (%) Minimum 80 90 70% 100 70% 40 50 60 Load (%) Cooling 95% 90% Humidity Typical 115VAC input Maximum 230VAC input Units +70 °C -40 70 80 90 100 230VAC input 5 10 20 30 40 50 60 70 80 90 100 Forced-cooled 95 %RH 230VAC input 5000/4000 m 115VAC input Notes & Conditions -40°C for 150W load, -25°C for 225W load. See derating curves, figures 5 and 6 °C CFM Operating Altitude 80% +85 10 Convecon-cooled 85% 115VAC input Load (%) Forced-cooled -40 Operating Temperature 75% 100% Forced-cooled 80% 80% Storage10Temperature 20 30 Convecon-cooled 85% 75% Environmental 90% Efficiency 80 Forced-cooled 80% 75% Efficiency 70 85% 80% 70% 95% 60 Load (%) 100% 75% 85% 100% 10 90% Forced-cooled Efficiency Efficiency Convecon-cooled 90% 70% 50 95% 75% 100% 90% 40 Load (%) 80% 95% 70% 30 Convecon-cooled Load (%) 85% 70% 20 75% 90% 100% 10 80% 95% 70% 95% 230VAC input 90% Figure 2 85% UCP225PS12-A 75% 100% 115VAC input 80% 70% 95% 80% 70% Forced-cooled 75% 100% 100% Efficiency vs Load 95% 90% Figure 1 85% UCP225PS12 Convecon-cooled 85% Forced-cooled >150W Non-condensing ITE/Medical 3 x 30g shocks in each plane, total 18 shocks. 30g = 11ms (+/- 0.5msecs), half sine. Conforms to EN60068-2-27 Shock 75% Vibration 70% 10 Single axis 10-500 Hz at 2g sweep and endurance at resonance in all 3 planes. Conforms to EN60068-2-6 20 30 40 50 60 70 80 90 100 Load (%) 4 UCP225 Series AC-DC POWER SUPPLIES Applications Notes Temperature Derating Curves 225 0 -40 -20 0 0 -40 -20 0+50 +70 +50 0 -25 +70 Ambient TemperatureAmbient (ºC) Temperature (ºC) -20 Output Load (W) 112 225 Some specificaon parameters may not be met Output Load (W) 75 Some specificaon parameters may not be met 75 Output Load (W) 150 Some specificaon parameters may not be met Output Load (W) 150 Figure 6 225W Forced Cooled 112 0 0 -25 Some specificaon parameters may not be met Figure 5 150W Convection Cooled -20 0+50 +70 +50 +70 Ambient TemperatureAmbient (ºC) Temperature (ºC) EMC: Emissions Phenomenon Standard Test Level Notes & Conditions Conducted EN55011/32 Class B Radiated EN55011/32 Class A Class B with King Core ferrites: Output cable: KCF-130-B, Input cable for 150W load: K5B RC 14x28.5x7-M for all models with additional KCF-130-B on 48V version. Input cable for 225W load: K5B RC 14x28.5x7-M plus KCF-130-B. Harmonic Current EN61000-3-2 Class A Meets Class C for loads above 145W Voltage Functions EN61000-3-3 Specifications subject to change without notice. 5 UCP225 Series AC-DC POWER SUPPLIES EMC: Immunity Phenomenon Medical Device EMC Standard Test Level Criteria IEC60601-1-2 Ed.4.0 as below EN61204-3 High severity level as below ESD EN61000-4-2 4 A Radiated EN61000-4-3 3 A EFT EN61000-4-4 3 A Surges EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 3 A Magnetic Fields EN61000-4-8 4 A Dip >95% (0VAC), 8.3ms A EN55035 (100VAC) Dip 30% (70VAC), 416ms A Dip >95% (0VAC), 4160ms B Dip >95% (0VAC), 10.0ms A Low Voltage PSU EMC EN55035 (240VAC) Dips and Interruptions EN60601-1-2 (100VAC) EN60601-1-2 (240VAC) Notes & Conditions ±8kV contact, ±15kV air Dip 30% (168VAC), 500ms A Dip >95% (0VAC), 5000ms B Dip 100% (0VAC), 10.0ms A Dip 100% (0VAC), 20ms B Performance criteria A