VR20S15

VR20 Series DC-DC Converter 2 Amp xxx Series • Non Isolated 2A Switching Regulator • Regulated Single Outputs from 2.5 to 15VDC • Wide Input Range to 36V • SIP3 Package • High Efficiency to 96% • Class B Conducted & Radiated Emissions • Short Circuit Protection • Low 0.1mA Standby Input Current • -40°C to +85°C Operation • MTBF >2MHrs • 3 Year Warranty Dimensions: The VR20 provides a cost effective compact efficient switching regulator solution operating from a wide range DC input. Output voltages start from 2.5V and the VR20 consumes as little as 0.1mA when idle. VR20: 0.453 x 0.689 x 0.354" (11.5 x 17.5 x 9.0mm) Models & Ratings Input Current(1) Efficiency(2) No Load Full Load Max. Capacitive Load 2.0A 0.2mA 1300mA 2000µF 89% 83% VR20S2V5 2.0A 0.1mA 1260mA 1800µF 89% 85% VR20S3V3 5.0V 2.0A 0.1mA 1380mA 1000µF 92% 89% VR20S05 13-36V 9.0V 2.0A 0.1mA 1490mA 680µF 95% 92% VR20S09 16-36V 12V 2.0A 0.1mA 1590mA 470µF 96% 94% VR20S12 18-36V 15V 2.0A 0.1mA 1760mA 470µF 96% 94% VR20S15 Input Voltage Output Voltage Output Current 4.5-36V 2.5V 6.0-36V 3.3V 8.0-36V Vin, Min. Vin, Max. Model Number Notes 1. Full load input current measured at minimum input voltage. 2. Efficiency measured at full load. 3. Standard tube quantity 44 pcs. 4. Right angle pin option, add suffix -RA. Mechanical Details FRONT VIEW RIGHT ANGLE PIN OPTION (-RA) FOOTPRINT (TOP VIEW) UNDERSIDE VIEW 0.689 (17.5) 0.200 (5.08) 0.354 (9.00) 0.453 (11.50) 0.748 (19.0) VR20 0.689 (17.5) 0.020 (0.50) 0.354 (9.0) 0.085 (2.15) 1 2 3 0.100 (2.54) TYP. 0.012 (0.30) Ø0.039 ( Ø1.00) 0.028 (0.70) 0.161 (4.10) 0.200 (5.08) 0.012 (0.3) Notes 1. All dimensions are in inches (mm) 2. Weight: 0.0083lbs (3.8g) approx. 3. Pin diameter: 0.02±0.004 (0.7±0.1) 1 4. Case & pin tolerance: ±0.02 (±0.5) www.xppower.com Pin Connections 1 2 3 Pin 1 2 3 Single +Vin Ground +Vout VR20 Series DC-DC Converter Input Maximum Units Notes & Conditions 36 VDC See Models and Ratings table. Input Reflected Ripple 20 mA pk-pk Input Surge 45 VDC For max. 100ms. Maximum Units Notes & Conditions 15 VDC See Models and Ratings table. ±4.0/±3.0 % 2.5V and 3.3V/others (At full load) mA No minimum load required. % % Full load over input voltage range. Maximum variation applies to 2.5V output models. For 50% load change. Recovery in 200µs. Characteristic Input Voltage Range Input Filter Minimum Typical 4.5 Internal capacitor Output Characteristic Minimum Output Voltage 2.5 Initial Set Accuracy Minimum Load Typical ±2.0 0 Line Regulation Load Regulation ±0.4 ±0.5 ±0.8 ±1.5 Transient Response ±5 % Ripple & Noise 75 mV pk-pk Short Circuit Protection Continuous, with auto recovery. Hiccup mode. Maximum Capacitive Load See Models and Ratings table. Temperature Coefficient 0.03 20 MHz bandwidth. %/ ˚C Overload Protection 3.5 A Start-up Time 20 ms General Characteristic Minimum Typical Maximum Units 96 % Efficiency Isolation: Input to Output 0 Switching Frequency Mean Time Between Failure 400 kHz 2 Weight Case Material VDC MHrs 0.0083 (3.8) Notes & Conditions See models and ratings table. Non isolated. At full load. MIL-HDBK-217F. lb (g) Non-conductive black plastic UL94V-0. Pin Material Solder coated phosphor bronze C5191R-1/2H. Potting Material Polyurethane type L780 UL94V-0 rated. Water Wash Use de-ionised water only, dry thoroughly. Soldering Temperature 260 °C Wave solder peak, 1.5mm from case 10s max. Not suitable for vapour phase soldering. For further details contact XP Power applications team. Environmental Characteristic Maximum Units Notes & Conditions Operating Temperature Minimum -40 +85 °C See derating curves. Storage Temperature -55 +125 °C Case Temperature Humidity Cooling Typical +120 °C 95 %RH Non-condensing. Natural convection. www.xppower.com 2 VR20 Series DC-DC Converter EMC: Emissions Phenomenon Conducted Radiated Test Level Class B Class B Standard EN55032 EN55032 Notes & Conditions See Application Notes EMC: Immunity Standard Test Level Criteria Notes & Conditions EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 ±6kV 10V/m ±1.0kV ±1.0kV 3Vrms B A B B A Contact discharge. Phenomenon ESD Immunity Radiated Immunity EFT/Burst Surges Conducted Immunity V See Application Notes Application Notes Input Filter to meet Class B Conducted Emissions +Vin L Fuse 1 Vin VR20 +Vo 3 L C1 C2/C3 C4 C5 22µH 100µF/100V 10µF/50V 680µF/50V 22µF/25V GND C1 + C2 + C3 + C4 + 2 C5 + Load Select fuse rating based on application input current. Ground Typical Application Part Number 1 +Vin Vin C6 + VR20 GND 2 +Vo 3 +Vout Ground VR20S3V3 22µF/10V VR20S09 Ground C7 22µF/10V VR20S05 C7 + C6 VR20S2V5 22µF/50V 22µF/10V 22µF/16V VR20S12 22µF/25V VR20S15 22µF/25V Derating Curves 2.5V/3.3V/5V output 100 80 >32V 60 Vin ≤32V 40 0 -40 OUTPUT POWER OUTPUT POWER (%) 100 (%) 120 20 3 9V/12V/15V output 120 80 70 >32V 60 >24V Vin ≤24V 40 30 20 85 40 55 71 AMBIENT TEMPERATURE(° & ) 0 0 -40 www.xppower.com 85 0 40 55 71 AMBIENT TEMPERATURE(° & ) 09 June 2020