NJ88C24MADP

NJ88C24 Frequency Synthesiser with non-resettable counters DS2438 - 2.3 The NJ88C24 is a synthesiser circuit fabricated on the GPS CMOS process and is capable of achieving high sideband attenuation and low noise performance. It contains a reference oscillator, 11-bit programmable reference divider, digital and sample-and-hold comparators, 10-bit programmable ‘M’ counter, 7-bit programmable ‘A’ counter and the necessary control and latch circuitry for accepting and latching the input data. Data is presented serially under external control from a suitable microprocessor. Although 28 bits of data are initially required to program all counters, subsequent updating can be abbreviated to 17 bits, when only the ‘A’ and‘M’ counters require changing. The NJ88C24 is intended to be used in conjunction with a two-modulus prescaler such as the SP8710 or SP8705 series to produce a universal binary coded synthesiser for up to 1100MHz operation. PDA PDB LD FIN VSS VDD OSC IN OSC OUT 1 2 3 4 16 15 14 13 CH RB MC PDA PDB NC ENABLE LD FIN CLOCK VSS DATA VDD NC NC OSC IN CAP 1 2 3 4 5 6 7 8 9 18 17 16 15 NJ88C24 14 13 12 11 10 CH RB MC CAP ENABLE CLOCK DATA NC OSC OUT NJ88C24 5 6 7 8 12 11 10 9 DG16, DP16 MP18 FEATURES s Low Power Consumption Fig.1 Pin connections - top view (not to scale) s s s s High Performance Sample and Hold Phase Detector Serial Input with Fast Update Feature >20MHz Input Frequency Fast Lock-up Time ABSOLUTE MAXIMUM RATINGS Supply voltage, VDD2VSS: Input voltage Open drain output, LD pin: All other pins: Storage temperature: 20·5V to 7V 7V VSS20·3V to VDD10·3V 255°C to 1125°C (DP and MP packages) 265°C to 1150°C (DG package) CAP 17 (15) CH 16 (18) ORDERING INFORMATION NJ88C24 MA DG Ceramic DIL Package NJ88C24 MA DP Plastic DIL Package NJ88C24 MA MP Miniature Plastic DIL Package RB 15 (17) OSC IN OSC OUT 7 (9) 8 (10) LATCH 6 LATCH 7 LATCH 8 10 (12) DATA 12 (14) ENABLE 11 (13) REFERENCE COUNTER (11BITS) 42 fr SAMPLE/HOLD 1 (1) PDA PHASE DETECTOR ‘R’ REGISTER fV FREQUENCY/ PHASE DETECTOR 2 (2) PDB CLOCK ‘M’ REGISTER ‘A’ REGISTER 3 (4) LOCK DETECT (LD) VSS LATCH 1 LATCH 2 LATCH 3 LATCH 4 LATCH 5 FIN 4 (5) ‘M’ COUNTER (10 BITS) ‘A’ COUNTER (7 BITS) VDD VSS 6 (7) CONTROL LOGIC 5 (6) 14 (16) MODULUS CONTROL OUTPUT (MC) Fig.2 Block diagram NJ88C24 ELECTRICAL CHARACTERISTICS AT VDD = 5V Test conditions unless otherwise stated: VDD–VSS=5V ± 0·5V. Temperature range = –40°C to +85°C DC Characteristics Value Characteristic Min. Supply current Modulus Control Output (MC) High level Low level Lock Detect Output (LD) Low level Open drain pull-up voltage PDB Output High level Low level 3-state leakage current AC Characteristics Value Characteristic Min. FIN and OSC IN input level Max. operating frequency, fFIN and fosc Propagation delay, clock to modulus control MC Programming Inputs Clock high time, tCH Clock low time, tCL Enable set-up time, tES Enable hold time, tEH Data set-up time, tDS Data hold time, tDH Clock rise and fall times High level threshold Low level threshold Hysteresis Phase Detector Digital phase detector propagation delay Gain programming resistor, RB Hold capacitor, CH Programming capacitor, CAP Output resistance, PDA 200 20 30 0·5 0·5 0·2 0·2 0·2 0·2 50 Typ. Max. mV RMS 10MHz AC-coupled sinewave MHz Input squarewave VDD to VSS, 25°C. ns See note 2 Units Conditions Typ. Max. 5·5 1.5 4·6 0·4 0·4 7·0 4·6 0·4 ± 0·1 mA mA V V V V V V µA fosc, fFIN = 10MHz fosc, fFIN = 1MHz ISOURCE = 1mA ISINK = 1mA ISINK = 4mA    0 to 5V square wave Units Conditions ISOURCE = 5mA ISINK = 5mA tCH 0·2 VDD20·8 0·8 1·0 500 5 1 1 5 See note 1 See note 1 See note 1 ns kΩ nF nF kΩ NOTES 1. Data, Clock and Enable inputs are high impedance Schmitt buffers without pull-up resistors; they are therefore not TTL compatible. 2. All counters have outputs directly synchronous with their respective clock rising edges. 3. The finite output resistance of the internal voltage follower and ‘on’ resistance of the sample switch driving this pin will add a finite time constant to the loop. An external 1nF hold capacitor will give a maximum time constant of 5µs. 4. The inputs to the device should be at logic ‘0’ when power is applied if latch-up conditions are to be avoided. This includes the signal/osc. frequency inputs. 2          µs µs µs µs µs µs µs V V V All timing periods are referenced to the negative transition of the clock waveform See note 3 NJ88C24 PIN DESCRIPTIONS Pin no. DG,DP MP Name PDA Description Analog output from the sample and hold phase comparator for use as a ‘fine’ error signal. Voltage increases as fv (the output from the ‘M’ counter) phase lead increases; voltage decreases as fr (the output from the reference counter) phase lead increases. Output is linear over only a narrow phase window, determined by gain (programmed by RB). In a type 2 loop, this pin is at (VDD2VSS)/2 when the system is in lock. Three-state output from the phase/frequency detector for use as a ‘coarse’ error signal. fv. fr or fv leading: positive pulses with respect to the bias point VBIAS fv , fr or fr leading: negative pulses with respect to the bias point VBIAS fv = fr and phase error within PDA window: high impedance. Not connected. An open-drain lock detect output at low level when phase error is within PDA window (in lock); high impedance at all other times. The input to the main counters. It is normally driven from a prescaler, which may be AC-coupled or, when a full logic swing is available, may be DC-coupled. Negative supply (ground). Positive supply (normally 5V) Not connected. 1 1 2 2 PDB – 3 4 5 6 – 7, 8 3 4 5 6 7 8 NC LD FIN VSS VDD NC 9,10 OSC IN/ These pins form an on-chip reference oscillator when a series resonant crystal is connected across OSC OUT them. Capacitors of appropriate value are also required between each end of the crystal and ground to provide the necessary additional phase shift. The addition of a 220Ω resistor between OSC OUT and the crystal will improve stability. An external reference signal may, alternatively, be applied to OSC IN. This may be a low-level signal, AC-coupled, or if a full logic swing is available it may be DC-coupled. The program range of the reference counter is 3 to 2047 , with the total division ratio being twice the programmed number. – 12 NC DATA Not connected. Information on this input is transferred to the internal data latches during the appropriate data read time slot. DATA is high for a ‘1’ and low for a ‘0’. There are three data words which control the NJ88C24; MSB is first in the order: ‘A’ (7 bits), ‘M’ (10 bits), ‘R’ (11 bits). Data is clocked on the negative transition of the CLOCK waveform. If less than 28 negative clock transitions have been received when the ENABLE line goes low (i.e., only ‘M’ and ‘A’ will have been clocked in), then the ‘R’ counter latch will remain unchanged and only ‘M’ and ‘A’ will be transferred from the input shift register to the counter latches. This will protect the ‘R’ counter from being corrupted by any glitches on the clock line after only ‘M’ and ‘A’ have been loaded If 28 negative transitions have been counted, then the ‘R’ counter will be loaded with the new data. When ENABLE is low, the DATA and CLOCK inputs are disabled internally. As soon as ENABLE is high, the DATA and CLOCK inputs are enabled and data may be clocked into the device. The data is transferred from the input shift register to the counter latches on the negative transition of the ENABLE input and both inputs to the phase detector are synchronised to each other. This pin allows an external capacitor to be connected in parallel with the internal ramp capacitor and allows further programming of the device. (This capacitor is connected from CAP to VSS). Modulus control output for controlling an external dual-modulus prescaler. MC will be low at the beginning of a count cycle and will remain low until the ‘A’ counter completes its cycle. MC then goes high and remains high until the ‘M’ counter completes its cycle, at which point both ‘A’ and ‘M’ counters are reset. This gives a total division ratio of MP1A, where P and P11 represent the dual-modulus prescaler values. The program range of the ‘A’ counter is 0-127 and therefore can control prescalers with a division ratio up to and including 4128/129. The programming range of the ‘M’ counter is 8-1023 and, for correct operation, M>A. Where every possible channel is required, the minimum total division ratio N should be: N>P 22P, where N = MP1A. An external sample and hold phase comparator gain programming resistor should be connected between this pin and VSS. An external hold capacitor should be connected between this pin and VSS. 9 10 11 13 CLOCK 12 14 ENABLE 13 14 15 16 CAP MC 15 16 17 18 RB CH 3 NJ88C24 2·0 VDD = 5V OSC IN, FIN = 0V TO 5V SQUARE WAVE SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) 1·5 8 7 6 5 4 3 2 TOTAL SUPPLY CURRENT IS THE SUM OF THAT DUE TO FIN AND OSC IN 1 2 3 4 5 6 7 INPUT FREQUENCY (MHz) 8 9 10 1 10MHz 1MHz VDD = 5V FIN = LOW FREQUENCY 0V TO 5V SQUARE WAVE OSC IN 1·0 FIN 0·5 0·2 0·4 0·6 0·8 1·0 1·2 INPUT LEVEL (V RMS) 1·4 1·6 Fig. 3 Typical supply current v. input frequency Fig. 4 Typical supply current v. input level, OSC IN PROGRAMMING Reference Divider Chain The comparison frequency depends upon the crystal oscillator frequency and the division ratio of th ‘R’ counter, which can be programmed in the range 3 to 2047, and a fixed divide by two stage. fosc R= 23fcomp where fosc = oscillator frequency, fcomp = comparison frequency, R = ‘R’ counter ratio For example, where the crystal frequency = 10MHz and a channel spacing comparison frequency of 12·5kHz is required, Note that M>A and N = fVCO fcomp For example, if the desired VCO frequency = 275MHz, the comparison frequency is 12·5kHz and a two-modulus prescaler of 464/65 is being used, then 6 N = 275310 = 223103 12·53103 Now, N = MP1A, which can be rearranged as N/P = M1A/P. In our example we have P = 64, therefore A 223103 = M1 64 64 R= 107 = 400 2312·53103 Thus, the ‘R’ register would be programmed to 400 expressed in binary. The total division ratio would then be 23400 = 800 since the total division ratio of the ‘R’ counter plus the 42 stage is from 6 to 4094 in steps of 2. VCO Divider Chain The synthesised frequency of the voltage controlled oscillator (VCO) will depend on the division ratios of the ‘M’ and ‘A’ counters, the ratio of the external two-modulus prescaler (P/P11)and the comparison frequency . The division ratio N = MP1A, where M is the ratio of the ‘M’ counter in the range 8 to 1023 and A is the ratio of the ‘A’ counter in the range 0 to 127. such that M = 343 and A /64 = 0·75. Now, M is programmed to the integer part = 343 and A is programmed to the fractional part364 i.e., A = 0·75364 = 48. NB The minimum ratio N that can be used is P 22P (=4032 in our example) for all contiguous channels to be available. To check: N = 343364148 = 22000, which is the required division ratio and is greater than 4032 ( = P 22P ). When re-programming, the counters are changed only at the zero state. There is no reset to zero , which means that the synthesiser loop lock-up time will be variable. When only small changes in frequency are required, the non-resettable synthesiser should achieve the shortest loop lock-up times. CLOCK tCH tCL ENABLE tEH tES tDS tEH tDH tES DATA Fig. 5 Timing diagram showing timing periods required for correct operation 4 NJ88C24 1 CLOCK 2 3 4 5 (15)26 (16)27 (17)28 ENABLE DATA A6 A5 A4 A3 A2 (M2)R2 (M1)R1 (M0)R0 Fig.6 Timing diagram showing programming details PHASE COMPARATORS Noise output from a synthesiser loop is related to loop gain: KPD KVCO N where KPD is the phase detector constant (volts/rad), KVCO is the VCO constant (rad/sec/volt) and N is the overall loop division ratio. When N is large and the loop gain is low, noise may be reduced by employing a phase comparator with a high gain. The sample and hold phase comparator in the NJ88C24 has a high gain and uses a double sampling technique to reduce spurious outputs to a low level. A standard digital phase/frequency detector driving a threestate output,PDB, provides a ‘coarse’ error signal to enable fast switching between channels. The PDB output is active until the phase error is within the sample and hold phase detector window, when PDB becomes high impedance. Phase-lock is indicated at this point by a low level on LD. The sample and hold phase detector provides a ‘fine’ error signal to give further phase adjustment and to hold the loop in lock. An internally generated ramp, controlled by the digital output from both the reference and main divider chains, is sampled at the reference frequency to give the ‘fine’ error signal, PDA. When in phase lock, this output would be typically at (VDD2VSS)/2 and any offset from this would be proportional to phase error. The relationship between this offset and the phase error is the phase comparator gain, KPDA, which is programmable with an external resistor, RB, and a capacitor, CAP. An internal 50pF capacitor is used in the sample and hold comparator. CRYSTAL OSCILLATOR When using the internal oscillator, the stability may be enhanced at high frequencies by the inclusion of a resistor between the OSC OUT pin and the other components. A value of between 150Ω and 270Ω is advised, depending on the crystal series resistance. PROGRAMMING/POWER UP Data and signal input pins should not have input applied to them prior to the application of VDD, as otherwise latch-up may occur. 5 For more information about all Zarlink products visit our Web Site at w ww.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE