SL6140

SL6140 SL6140 400MHz Wideband AGC Amplifier DS2159 ISSUE 5.0 July 1999 Features • • • • • • 400MHz Bandwidth (RL=50 Ω) High voltage Gain 45dB (R L=1kΩ) 70dB Gain Control Range High Output Level at Low Gain Surface Mount Plastic Package Low Cost Ordering Information SL6140/NA/MP Industrial temperature range miniature plastic package SL6140/NA/MPTC Tape and Reel Applications • • • RF/IF Amplifier High Gain Mixers Video Amplifiers Description The SL6140 is an integrated broadband AGC amplifier, designed on an advanced bipolar process. The amplifier provides over 15dB of linear gain into 50Ω at 400MHz. Gain control is also provided with over 70dB of dynamic range. The SL6140 offers over 45dB of voltage gain with an RL of 1kΩ. The SL6140 (Figure 3) is a high gain amplifier with an AGC control capable of reducing the gain of the amplifier by over 70dB. The gain is adjustable by applying a voltage to the AGC input via an external resistor (RAGC), the value of which adjusts the curve of gain reduction versus control voltage (see Figure 4). As the output stage of the amplifier is an open collector the maximum voltage gain is determined by RL. With load resistance of 1kΩ the single ended voltage gain is 45dB and with a load resistance of 50 Ω the voltage gain is 15dB (20log10 VOUT/VIN ). Another parameter that depends on the load resistance is the bandwidth: 25MHz for RL = 1kΩ , as compared with 400MHz for RL = 50Ω . RL is chosen to give either the required bandwidth or voltage gain for the circuit. Figure 7 through to 10 show the typical S parameters for the device. Figures 11 and 12 show the typical variation in 3rd order intercept performance with AGC. In any application, the substrate should be connected to the most negative point in the circuit, usually to the same point as pin 3. +VCC 1.0 F +VCC 2 RL 10n RAGC AGC INPUT 10n INPUT 6 5 8 RL 10n OUTPUT SL6140 4 1 10n OUTPUT 3 7 Figure 1 - Typical Application 1 SL6140 OUTPUT +VCC GROUND INPUT 1 2 3 4 8 7 6 5 OUTPUT GROUND INPUT AGC INPUT MP8 Figure 2 - Pin Connections Diagram (top view) Electrical Characteristics Tamb = 25°C, VCC = 12V +5%, VIN = 1mVRMS, Frequency = 6MHz, Load (RL) = 10KOHms, RAGC = 22KOHm These characteristics are guaranteed over the following conditions (unless otherwise stated) Characteristic Supply current Output stage current Pin 5,6,7 5,6 (sum) 5,6 5 Value Min Typ 19 7 Max 23 9 Units mA mA Conditions No input signal No input signal Output current matching (magnitude of difference of output currents) AGC range 1.0 mA 2 60 75 dB See Figure 4 & Note 1 (VAGC = 0V to 10V) RL = 1kΩ See Figure 5 & Note 1 Tuned input and output RL = 50Ω RL = 1kΩ See Figure 5 RL = 50Ω Voltage gain (single ended) 5,6 5,6 40 45 55 15 25 400 dB dB dB MHz Bandwidth (-3dB) 5,6 Maximum output level (single ended) 0dB AGC -30dB AGC Noise figure Note. 1 Guaranteed but not tested. 5,6 5,6 5,6 3.5 3.5 5 V p-p V p-p dB Note 1 RL = 1kΩ. Note 1 Test CCT Figure 13 Absolute Maximum Ratings Supply voltage, VCC Input voltage (differential) AGC supply Storage temperature Operating temperature range SL6140 MP Chip operating temperature SL6140 MP +18V +5V VCC -55°C to +150°C -40°C to +85°C at 200mW +150°C Thermal Resistance Chip-to-ambient SL6140 MP Chip-to-case SL6140 MP 163°C/W 57 °C/W 2 SL6140 2 VCC 470 X2 180 AGC I/P 5 70 8 180 7k 12.1k OUTPUT 470 470 1 OUTPUT 2k 4 INPUT 1.4k 45 6 INPUT 66 2.8k 200 200 2.8k 5k 5k 5.6k 1.1k 1.1k 2.1k 1.9k 200 7 3 SUBSTRATE GROUND Figure 3 - Full Circuit Diagram of SL6140 3 SL6140 G A I N R E D U C T I O N (dB) 0 10 20 30 40 RAGC=5.6k RAGC=22k 50 60 70 0 1 2 3 4 5 6 7 8 9 10 AGC VOLTAGE Figure 4 - Gain Reduction v. AGC Voltage 8 D I F F E R E N T I A L O U T P U T (V p-p) 7 6 5 4 1MHzSINEWAVE 3 2 1 0 0 10 20 30 40 50 GAIN REDUCTION (dB) Figure 5 - Max Differential O/P Voltage v. Gain Reduction 4 SL6140 50 RL=1kΩ 40 dB 30 G A I N 20 RL=50Ω 10 0 0.1 10 100 1000 FREQUENCY (MHz) Figure 6 - Voltage Gain v. Frequency Figure 7 - Input Impedance 50Ω System 5 SL6140 Figure 8 - Output Impedance 50Ω System Figure 9 - Reverse Transmission Coefficient S12 SL6140 6 SL6140 Figure 10 - Forward Transmission Coefficient S12 SL6140 Figure 11 3rd Order Intercept Point Against Gain Reduction At 250.0MHz and 254.0MHz 7 SL6140 Figure 12 - 3rd Order Intercept Point Against Gain Reduction At 100.0MHz and 104.0MHz +12V 1nF 6 2 1 L1 5 8 7 4 1nF 3 L2 O/P VARIABLE CAPS 3-25pF L1 7 TURNS # 18 SWG L2 6 TURNS # 16 SWG 8mm DIA 16mm LONG 14mm DIA 19mm LONG Figure 13 - 50MHz Noise Figure Test Circuit 8 For more information about all Zarlink products visit our Web Site at w ww.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE