SP8401KGMPES

SP8401 Very Low Phase Noise 300MHz ÷ 10/11 DS3230 ISSUE 3.1 April 1994 The SP8401 is a very low phase noise variable modulus divider. Special circuit techniques have been used to reduce the phase noise considerably below that produced by standard dividers. The modulus control input is CMOS or TTL compatible. The SP8401 is packaged in a 28 pin plastic SO package to be compatible with the SP8400 and SP8402 devices. Ordering Information SP8401 KG MPES(Commercial Grade) FEATURES I Very low Phase Noise (Typically -160dBc/Hz at 1kHz offset) I Supply Voltage 5V N/C N/C N/C VCC +5V GND CLOCK INPUT CLOCK INPUT CLOCK INPUT CLOCK INPUT GND VCC +5V VCC +5V N/C MODULUS CONTROL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 N/C N/C N/C N/C N/C N/C N/C OUTPUT OUTPUT N/C VCC +5V N/C N/C N/C ABSOLUTE MAXIMUM RATINGS Supply Voltage Output Current Storage Temperature Range Maximum Clock Input Voltage 6.5V 20mA -55°C to +125°C 2.5V p-p MP28 Fig.1 Pin connections - top view 0 –10 –20 –30 –40 –50 (f) (dBc/Hz) –3dB –60 –70 –80 –90 –100 –110 –120 –130 –140 –150 –160 –170 1 10 100 Frequency (Hz) 1k 10k 100k Fig.2 Typical single sideband phase noise measured at 300MHz SP8401 ELECTRICAL CHARACTERISTICS Guaranteed over: Supply voltage V CC = +4.75V to +5.25V Temperature Tamb = -10°C to +75° C Tested at +4.75V and +5.25V at T amb = +25°C Characteristic Supply current Output voltage swing Input sensitivity 50MHz to 300MHz Pin Min. 4, 11, 12, 18 20, 21 7, 8 50 340 Value Typ. Max. 57 440 64 mA mV mV dBm Output loaded with 300R See Fig.5 p-p @ 330MHz input ÷ 11 mode Output loaded with 300R RMS Sine wave into 50 Ohms (dBm equivalent) See Fig.3 Units Conditions 140 (-4) Modulus Control Inputs Logic high voltage Low low voltage Input current Set up time ts Release time tr 14 14 14 14 14 2.2 0.8 180 4 4 V µA ns ns ÷ 10 mode ÷ 11 mode Modulus control input voltage 5V 400 355mV VIN mV RMS 300 OPERATING WINDOW 200 140mV 100 0 50 100 150 200 250 300 350 INPUT FREQUENCY (MHz) Fig.3 Typical input sensitivity CLOCK INPUT MODULUS CONTROL INPUT tr 6 OUTPUT 5 5 ts Fig.4 Timing diagram 2 SP8401 VCC 1 2 3 4 5 28 27 26 25 24 23 22 1nF 50R RF SIGNAL GENERATOR 6 7 8 9 10 11 12 13 SP8401 21 20 19 18 17 16 15 220nF OUTPUT TTL/CMOS MODULUS CONTROL 14 50R 1nF 10nF 1nF 2x330R 10nF Fig.4 Test circuit 3 For more information about all Zarlink products visit our Web Site at w ww.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE