SP8630BDG

ADVANCE INFORMATION DS3664-1·2 SP8630 600MHz410 The SP8630 is an asynchronous emitter coupled logic divider which provides an ECLlll/10K compatible output when used with an external pulldown resistor. It requires an AC coupled input of 600mV p-p. NC NC NC OUTPUT NC 1 2 3 4 5 6 7 14 13 12 VCC (0V) NC INTERNAL BIAS DECOUPLING NC CLOCK INPUT NC NC FEATURES s ECL Compatible Outputs s AC-Coupled Inputs (Internal Bias) QUICK REFERENCE DATA s Supply Voltage: 25·2V SP8630 11 10 NC VEE 9 8 s Power Consumption: 350mW s Temperature Range: 230°C to 170°C DG14 Fig. 1 Pin connections - top view ABSOLUTE MAXIMUM RATINGS Supply voltage, VEE Output current Storage temperature range Max. junction temperature Max. clock input voltage 28V 15mA 265°C to 1150°C 1175°C 2·5V p-p ORDERING INFORMATION SP8630 B DG 5962-92003 (SMD) VCC (0V) 14 D CLOCK INPUT 10 42 REF Q D Q REF D Q 4 OUTPUT Q CK CK Q CK CK Q CK CK 12 INTERNAL BIAS DECOUPLING 7 VEE Fig. 2 Functional diagram SP8630 ELECTRICAL CHARACTERISTICS Unless otherwise stated, the Electrical Characteristics are guaranteed over specified supply, frequency and temperature range Supply voltage, VCC = 0V, VEE = 25·2V 6 0·25V Temperature, TAMB = 230°C to 170°C Value Characteristic Maximum frequency (sinewave input) Minimum frequency (sinewave input) Power supply current Output low voltage Output high voltage Minimum output swing Symbol fMAX fMIN IEE VOL VOH VOUT Min. 600 40 70 21·5 20·7 Max. Units MHz MHz mA V V mV Conditions Input = 400-800mV p-p Input = 400-800mV p-p VEE = 25·2V VEE = 25·2V VEE = 25·2V VEE = 25·2V Notes 21·8 20·85 400 3 3 NOTES 1. The temperature coefficients of VOH = 11·63mV/°C, and VOL = 10·94mV/°C but these are not tested. 2. The test configuration for dynamic testing is shown in Fig.5. 3. Tested at 25°C only. 1200 1000 800 600 400 200 0 0 100 200 300 400 INPUT FREQUENCY (MHz) 500 600 TAMB = 230°C TO 170°C INPUT AMPLITUDE (mV p-p) GUARANTEED * OPERATING WINDOW * Tested as specified in table of Electrical Characteristics Fig. 3 Typical input characteristic j1 j 0.5 j2 j 0.2 j5 0 0.2 0.5 600 1 400 200 2 5 50 2j 5 2j 0.2 2j 0.5 2j 1 2j 2 Fig. 4 Typical input impedance. Test conditions: supply voltage = 25·2V, ambient temperature = 25°C, frequencies in MHz, Impedances normalised to 50Ω 2 SP8630 OPERATING NOTES 1. The clock input (pin 10) should be capacitively coupled to the signal source. The input signal path is completed by connecting a capacitor from the internal bias decoupling, pin 12, to ground. 2. The circuit will operate down to DC but slew rate must be better than 100V/µs. 3. The output is compatible with ECLll. There is an internal load of 3kΩ at the output. The output can be interfaced to ECLlll/10K by the addition of 1·5kΩ to the output to increase the output voltage swing. 4. Input impedance is a function of frequency, see Fig. 4. 5. All components should be suitable for the frequency in use. 1n INPUT FROM GENERATOR 33 33 TO SAMPLING SCOPE 20 1n 10 12 1n 13 14 DUT 7 4 450 1n OUTPUT TO SAMPLING SCOPE VEE 1n Fig. 5 Test circuit 14 1n INPUT 10 400 15k 12 1n DIVIDE BY 10 3k 4 ECL OUTPUT BIAS 1·5k 7 25·2V 1n Fig. 6 Typical application showing interfacing 3 SP8630 PACKAGE DETAILS Dimensions are shown thus: mm (in). 1 5·59/7·87 (0·220/0·310) 14 0·20/0·36 (0·008/0·014) PIN 1 REF NOTCH 7·62 (0·3) NOM CTRS 1·14/1·65 (0·045/0·065) 20·32 (0·800) MAX SEATING PLANE 5·08/(0·20) MAX 0·51 (0·02) 3·18/4·06 MIN (0·125/0·160) 0·36/0·58 (0·014/0·23) 14 LEADS AT 2·54 (0·10) NOM. SPACING NOTES 1. Controlling dimensions are inches. 2. This package outline diagram is for guidance only. Please contact your GPS Customer Service Centre for further information. 14-LEAD CERAMIC DIL – DG14 HEADQUARTERS OPERATIONS GEC PLESSEY SEMICONDUCTORS Cheney Manor, Swindon, Wiltshire SN2 2QW, United Kingdom. Tel: (0793) 518000 Fax: (0793) 518411 GEC PLESSEY SEMICONDUCTORS P.O. Box 660017 1500 Green Hills Road, Scotts Valley, CA95067-0017 United States of America. Tel (408) 438 2900 Fax: (408) 438 5576 CUSTOMER SERVICE CENTRES q FRANCE & BENELUX Les Ulis Cedex Tel: (1) 64 46 23 45 Fax : (1) 64 46 06 07 q GERMANY Munich Tel: (089) 3609 06-0 Fax : (089) 3609 06-55 q ITALY Milan Tel: (02) 66040867 Fax: (02) 66040993 q JAPAN Tokyo Tel: (3) 5276-5501 Fax: (3) 5276-5510 q NORTH AMERICA Scotts Valley, USA Tel: (408) 438 2900 Fax: (408) 438 7023. q SOUTH EAST ASIA Singapore Tel: (65) 3827708 Fax: (65) 3828872 q SWEDEN Stockholm Tel: 46 8 702 97 70 Fax: 46 8 640 47 36 q UK, EIRE, DENMARK, FINLAND & NORWAY Swindon Tel: (0793) 518510 Fax : (0793) 518582 These are supported by Agents and Distributors in major countries world-wide. © GEC Plessey Semiconductors 1994 Publication No. DS3664 Issue No. 1.2 March 1994 This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior knowledge the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. 4 h ttp://www.zarlink.com World Headquarters - Canada Tel: +1 (613) 592 0200 Fax: +1 (613) 592 1010 North America - West Coast Tel: (858) 675-3400 Fax: (858) 675-3450 North America - East Coast Tel: (978) 322-4800 Fax: (978) 322-4888 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink Semiconductor’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips Zarlink and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2001, Zarlink Semiconductor Inc. All rights reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE