AO-162MGA00

AMP I RE SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED BY DATE Approved For Specifications Approved For Specifications & Sample AO-162MGA00 APPROVED BY CHECKED BY ORGANIZED BY DATE:2004/9/30 AMPIRE CO., LTD. 1 RECORD OF REVISION Revision Date 2004/5/5 2004/5/21 Page P.3 P.4 P.7 P.10 P.12 2004/7/1 2004/9/27 P.6 New Release Modify the operating temp min to –10 degrees Modify input voltage and logic supply current Add the pin connections diagram Modify ambient temperature to 20 degrees Modify reliability low temperature operation Modify the C1~C8 and C9~C16 Layout. Modify the LCD data according the prototype Modify the C1~C8 and C9~C16 Layout according the NT7651 ver1.0 data sheet. Add LCD initial setting 2004/9/30 Modify the pin length to 9.0min kokai Kokai Kokai Contents Editor Sam DATE:2004/9/30 AMPIRE CO., LTD. 2 1 FEATURES (1) Display format : 16 characters × 2 lines (2) Display type: STN Gray, Reflective, 6 o’clock view, Positive (3) Controller : NT7651H-BDT02 (4) I2C Interface (5) Adopt COG Technology 2 MECHANICAL DATA Parameter Dot size Dot pitch Character size Viewing area Module size Stand Value 0.55(W) × 0.6(H) 0.6(W) × 0.65(H) 2.95(W) × 5.15(H) 61.0(W) × 13.7(H) 66.0(W) × 27.7(H) Unit mm mm mm mm mm 3 ABSOLUTE MAXIMUM RATINGS Parameter Logic Circuit Supply Voltage LCD Driving Voltage Input Voltage Symbol VDD-VSS VLCD VIN TOP TSTG Min 0 0 VSS -10 -20 Max 3.5 6.5 VDD 50 70 Unit V V V °C °C Normal temp. type Operating Temp. Storage Temp. DATE:2004/9/30 AMPIRE CO., LTD. 3 4 ELECTRO-OPTICAL CHARACTERISTICS Parameter Logic Circuit Supply Voltage LCD Driving Voltage ( STN ) Input Voltage Logic Supply Current Contrast Rise Time Fall Time Viewing Angle Range Symbol Condition Min Typ Max Unit Note ----- Electronic Characteristics ----VDD-VSS VLCD -0 °C 25 °C 50 °C VIH VIL IDD --VDD = 3.3V 25°C 25°C 25°C 25°C & C R ≥2 -4.5 4.4 4.3 0.8VDD VSS -3.3 4.6 4.5 4.4 --0.2 -4.7 4.6 4.5 VDD 0.2VDD -V V mA V V . ----- Optical Characteristics ( STN ) ----CR tr tf θf θb θl θr Frame Frequency fF 25°C --------5.2 120 250 40 35 35 35 64 -180 400 -----Hz Deg. ms ms Note 3 Note 1 Note 2 (NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state) DATE:2004/9/30 AMPIRE CO., LTD. 4 ( NOTE 2 ) Response time : (NOTE 3) Viewing angle DATE:2004/9/30 AMPIRE CO., LTD. 5 5 BLOCK DIAGRAM DATE:2004/9/30 AMPIRE CO., LTD. 6 6 PIN CONNECTIONS 16 x 2 C C R R=10K , C=0.1uF PIN NO. SYMBOL 1 VLCD 2 VSS 3 VDD 4 SDA 5 POR 6 SCL LEVEL H/L H/L H/ L FUNCTION Internal Generated LCD Bias Voltage Power Ground Logic Power Supply Serial Data Input/Output External Power On Reset Serial Clock Input DATE:2004/9/30 AMPIRE CO., LTD. 7 7 LCD Initial Setting LCD_INIT: LCALL IC_START M OV A,#01110100B ;SLAVE ADDRESS LCALL SEND_BYTE M OV A,#00H ;SEND A CONTROL BYTE LCALL SEND_BYTE M OV A,#00110100b; ;FUNCTION SET 00100010 ; 001 DL,0,M SL,H LCALL M OV SEND_BYTE A,#0CH ;DISPLAY ON LCALL SEND_BYTE LCALL DELAY1S M OV LCALL M OV LCALL M OV LCALL A,#06H SEND_BYTE A,#00110101b; SEND_BYTE A,#10011111b; SEND_BYTE ;FUNCTION SET ; 001 DL,0,M SL,H ;VA=1 21h 00100010 ;ENTRY MODE SET ; VLCD = (integer value of register* 0.082) + 1.8=4.5v ;integer value of register=21h LCALL DELAY1S M OV A,#00110100b; ;FUNCTION SET ; 001 DL,0,M SL,H 00100010 LCALL SEND_BYTE ACALL RET IC_STOP DATE:2004/9/30 AMPIRE CO., LTD. 8 8 TIMING CHARACTERISTICS Write Operation DATE:2004/9/30 AMPIRE CO., LTD. 9 9 FONT TABLE DATE:2004/9/30 AMPIRE CO., LTD. 10 10 QUALITY AND RELIABILITY 10.1 TEST CONDITIONS Tests should be conducted under the following conditions : Ambient temperature : 20 ± 5°C Humidity : 60 ± 25% RH. 10.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan . 10.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 10.4 APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits. DATE:2004/9/30 AMPIRE CO., LTD. 11 10.5 INSPECTION QUALITY CRITERIA Item Function Dimension Black spots Description of defects Class of Defects Major Major Minor Acceptable level (%) 0.65 1.5 2.5 Black lines Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle Short circuit or Pattern cut Deviation from drawings Ave . dia . D area A area B Disregard D≤0.2 3 4 0.2