AZ6961-1C-15D

AZ6961 10 AMP SUBMINIATURE POWER RELAY FEATURES • • • • • • • • High sensitivity, 120 mW pickup Dielectric strength 5000 Vrms Isolation spacing greater than 8 mm 10 Amp switching capability Epoxy sealed version available Reinforced insulation, EN 60730-1 (VDE 0631, part 1) UL, CUR file E43203 VDE file 131637 CONTACTS Arrangement Ratings SPDT (1 Form C) SPST (1 Form A) Resistive load: Max. switched power: 240 W or 2500 VA Max. switched current: 10 A Max. switched voltage: 240* VDC or 440 VAC * Note: If switching voltage is greater than 30 VDC, GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 1 x 107 1 x 105 at 8 A 250 VAC res. 7 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) special precautions must be taken. Please contact the factory. Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance Insulation (according to DIN VDE 0110, IEC 60664-1) Dropout Ambient Temperature Operating Storage Vibration Shock Enclosure 1000 megohms min. at 20°C, 500 VDC, 50% RH C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Break Contact: 5 g at 10 …500 Hz Make Contact: 20 g at 10…500 Hz 10 g P.B.T. polyester, UL94 V-O Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 8 grams 20 per plastic tube / 1000 per carton box Rated Load UL, CUR 10 A at 250 VAC resistive [1] 8 A at 30 VDC / 250 VAC [1] 8 A at 30 VDC / 250 VAC, 100k cycles [2] B300 Pilot Duty [1] R300 Pilot Duty [1] 8 A at 250 VAC resistive, [1], [2] and [3] [1] Silver cadmium oxide, [2] Silver tin oxide, [3] Silver nickel VDE Material Resistance Silver cadmium oxide, silver tin oxide or silver nickel, gold plating available < 100 milliohms initially COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 120 mW 140 mW (60 VDC coil) 1.2 W at 20°C (68°F) ambient 20°C (36°F) at nominal coil voltage Max. 130°C (266°F) Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. Packing unit in pcs ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-07-29 Junkersstrasse 3, D-82178 Puchheim, Germany AZ6961 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 6 9 12 15 24 48 60 Must Operate VDC 3.5 4.2 6.3 8.4 10.5 16.8 33.6 42.0 Max. Continuous VDC 11.6 14.0 21.1 27.2 38.0 53.1 107.3 122.4 Coil Resistance Ohm 113 ± 10% 164 ± 10% 360 ± 10% 617 ± 10% 800 ± 10% 2,350 ± 10% 9,600 ± 15% 12,500 ± 15% ORDER NUMBER* 1 Form A (SPST-NO) AZ6961–1A–5D AZ6961–1A–6D AZ6961–1A–9D AZ6961–1A–12D AZ6961–1A–15D AZ6961–1A–24D AZ6961–1A–48D AZ6961–1A–60D 1 Form C (SPDT) AZ6961–1C–5D AZ6961–1C–6D AZ6961–1C–9D AZ6961–1C–12D AZ6961–1C–15D AZ6961–1C–24D AZ6961–1C–48D AZ6961–1C–60D * Add suffix “E” to “1A” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1C” for silver nickel contacts. Add suffix “E” at the end of order number for sealed version. Add suffix “A” for gold plated contacts. MECHANICAL DATA FORM C VERSION 1.132 Max. [28.75] .408 Max. [10.35] Coil Temperature Rise PC BOARD LAYOUT .062 [1.57] 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 .494 Max. [12.55] .298 [7.56] 1 FORM C .050 [1.3] .012 [0.3] .142 [3.6] .126 [3.2] .126 [3.2] Coil Temperature Rise °C 5 x ø .051 [ø 1.3] .870 [22.1] 10A 0A 60% 8 0% 100% 120% 140% 160% 180% 200% 220% 2 x ø .020 [ø 0.5] 3 x .016 [0.4] 3 x .031 [0.8] 4 x ø .051 [ø 1.3] .744 [18.9] .116 [2.95] .298 [7.56] 1 FORM A .198 [5.04] .050 [1.3] Percent of Nominal Coil Voltage at 20°C VIEWED TOWARD TERMINALS FORM A VERSION 1.132 Max. [28.75] .408 Max. [10.35] CIRCUIT DIAGRAM Maximum Switching Capacity 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 1 4 .494 Max. [12.55] 1 FORM C 2 3 5 DC Resistive Load 2.0 .142 [3.6] CURRENT .012 [0.3] AC Resistive Load 1.0 .9 .8 .7 .6 .5 2 x ø .020 [ø 0.5] 2 x .016 [0.4] 2 x .031 [0.8] 1 3 .4 .3 1 FORM A .2 2 4 10 100 VIEWED TOWARD TERMINALS VOLTAGE Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-07-29 Junkersstrasse 3, D-82178 Puchheim, Germany 1000 .1 20 30 40 50 60 70 80 90 200 300 400 500 600 700 800 900