AZ725-1A-60D

AZ725 16 AMP MINIATURE POWER RELAY HIGH INRUSH VERSION 120 AMP FEATURES • Dielectric strength 5000 Vrms • 16 Amp switching - single pole contacts • High inrush version: 120 Amp (20 ms) switching, contact gap > 0.6 mm • Isolation spacing greater than 8mm • Proof tracking index (PTI/CTI) 250 • Reinforced insulation, EN 60730-1 (VDE 0631, part 1) EN 60335-1 (VDE 0700, part 1) • UL, CUR file E43203 • VDE file 40013003 CONTACTS Arrangement Ratings SPDT (1 Form C) SPST (1 Form A and 1 Form B) Resistive load: Max. switched power: 480 W or 4000 VA Max. switched current: 16 A Max. switched voltage: 300 VDC* or 400 VAC * Note: If switching voltage is greater than 30 VDC, GENERAL DATA Life Expectancy Mechanical Electrical Minimum operations 3 x 107 1 x 105 at 16 A 250 VAC Res. High inrush version only: 1 x 105 at 1000 W 230 VAC tungsten lamp 3 x 104 at 3000 W 230 VAC tungsten lamp 1 x 104 at 2500 W 230 VAC halogen lamp 7 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) special precautions must be taken. Please contact the factory. Operate Time (typical) Release Time (typical) Rated Load UL, CUR VDE Material Resistance 16 A at 250 VAC resistive 16 A at 250 VAC resistive, 100k cycles Silver cadmium oxide or silver tin oxide < 30 milliohms initially Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts 2000 Vrms between open contacts (1 Form A high inrush version) Insulation Resistance Insulation (according to DIN VDE 0110, IEC 60664-1) Dropout 1000 megohms min. at 20°C, 500 VDC, 50% RH C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) 0.062" (1.5 mm) DA at 10–55 Hz 20 g P.B.T. polyester, UL94 V-0 Tinned copper alloy 270°C (518°F) 5 seconds 19 grams 50 per plastic tray / 1000 per carton box COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 270 mW 1.7 W at 20°C (68°F) ambient 32°C (58°F) nominal coil voltage Max. 130°C (266°F) Ambient Temperature Operating Storage Vibration Shock Enclosure Terminals NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. Max. Solder Temp. Max. Solder Time Weight Packing unit in pcs ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany AZ725 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 6 12 24 48 60 110 Must Operate VDC 3.5 4.2 8.4 16.8 33.6 42.0 77.0 Max. Continuous VDC 8.85 10.6 21.2 42.5 85.0 106.2 188.0 Coil Resistance Ohm ± 10% 49 68 260 1,100 4,400 7,000 20,500 ORDER NUMBER* Form A (SPST) AZ725–1A–5D AZ725–1A–6D AZ725–1A–12D AZ725–1A–24D AZ725–1A–48D AZ725–1A–60D AZ725–1A–110D Form C (SPDT) AZ725–1C–5D AZ725–1C–6D AZ725–1C–12D AZ725–1C–24D AZ725–1C–48D AZ725–1C–60D AZ725–1C–110D * Substitute “1B” in place of “1A” for Form B contacts. Add suffix “E” to “1A” or “1C” for silver tin oxide contacts Substitute “1AS” in place of “1A” for 1 Form A silver tin oxide contacts (120 A high inrush version). MECHANICAL DATA PC BOARD LAYOUT 1.16 MAX (29.5) .516 MAX (13.1) .295 (7.5) .197 (5.0) 1.01 MAX (25.6) .590 (15) .197 (5.0) 8 x ø .059 [ø 1.5] .142 (3.6) .016 (0.4) TYP .045 (1.1) TYP .118 (3.0) Viewed toward terminals WIRING DIAGRAMS Form A 8 7 5 4 7 6 4 3 Form B Form C 8 7 6 5 4 3 1 2 1 2 1 2 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany