AZ822-2C-18DSE

AZ822 SUBMINIATURE DIP RELAY FEATURES • • • • • • • • • Low profile for compact board spacing DC coils to 48 VDC Life expectancy to 10 million operations Standard PC 0.1" grid terminal spacing Fits standard 16 pin IC socket Epoxy sealed Meets FCC Part 68.302 1500 V lightning surge Meets FCC Part 68.304 1000 V dielectric UL, CUR file E43203 CONTACTS Arrangement Ratings DPDT (2 Form C) Bifurcated crossbar contacts Resistive load: Max. switched power: 60 W or 125 VA Max. switched current: 2A Max. switched voltage: 220 VDC* or 250 VAC * Note: If switching voltage is greater than 30 VDC, GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Capacitance Minimum operations 1 x 108 5 x 105 at 1 A 30 VDC (see table for additional figures) 5 ms at nominal coil voltage 2 ms at nominal coil voltage (with no coil suppression) Contact to contact: 1.2 pF Contact set to contact set: 1.6 pF Contact to coil: 1.5 pF At 10 mA contact current 2 ms at operate N.O. side 3 ms at operate N.C. side special precautions must be taken. Please contact the factory. Rated Load UL, CUR Material Resistance 1.0 A at 24 VDC 0.5 A at 120 VAC Silver palladium, gold clad < 50 milliohms initially Bounce (typical) Dielectric Strength 1000 Vrms contact to coil (at sea level for 1 min.) 1000 Vrms contact to contact 1000 Vrms between contact sets Insulation Resistance Dropout 1000 megohms min. at 20°C, 500 VDC, 50% RH Greater than 5% of nominal coil voltage At nominal coil voltage -55°C (-67°F) to 90°C (194°F) -55°C (-67°F) to 105°C (221°F) 0.062" (1.5 mm) DA at 10–55 Hz 20 g P.B.T. polyester (UL94 V-0) Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 4.5 grams 20 per plastic tube / 1000 per carton box COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 74 mW 3 - 12 V coils 98 mW 15 - 24 V coils 147 mW 48 V coils 0.94 W at 20°C (68°F) 15°C (27°F) at nominal coil voltage Max. 105°C (221°F) Ambient Temperature Operating Storage Vibration Shock Enclosure Terminals Max. Solder Temp. NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Relay adjustment may be affected if undue pressure is exerted on relay case. 4. Specifications subject to change without notice. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight Packing unit in pcs ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-08-22 Junkersstrasse 3, D-82178 Puchheim, Germany China AZ822 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 3 5 6 9 12 18 24 48 Must Operate VDC 2.1 3.5 4.2 6.3 8.4 12.6 16.8 33.6 Max. Continuous VDC 7.5 12.5 15.0 22.5 30.0 40.0 52.9 84.9 Coil Resistance Ohm ± 10% 60 167 240 540 960 1,620 2,880 7,680 ORDER NUMBER AZ822–2C–3DSE AZ822–2C–5DSE AZ822–2C–6DSE AZ822–2C–9DSE AZ822–2C–12DSE AZ822–2C–18DSE AZ822–2C–24DSE AZ822–2C–48DSE MECHANICAL DATA PC BOARD LAYOUT 8 x ø .03 [ø 0.8] .047 (1.2) REF .787 (20) .015 (0.38) .386 (9.8) .047 (1.2) REF 0.1 (2.54) .138 (3.5) .472 (12) Viewed toward terminals WIRING DIAGRAM .044 (1.11) .300 (7.61) .200 (5.07) .200 (5.07) (.020 ± .005) (0.5 ± 0.13) TYP .010 ± .005 (0.25 ± 0.13) TYP 1 4 6 8 16 13 11 9 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" TYPICAL CONTACT LIFE EXPECTANCY NUMBER OF OPERATIONS VOLTAGE 50 mV 30 VDC 30 VDC 30 VDC 60 VDC 60 VDC 60 VDC 30 VAC 30 VAC 30 VAC 60 VAC 60 VAC 60 VAC 125 VAC 125 VAC 125 VAC CURRENT 1 mA 1A 0.7 A 0.3 A 0.5 A 0.3 A 0.2 A 2A 1.3 A 0.7 A 1A 0.7 A 0.3 A 0.5 A 0.3 A 0.2 A RESISTIVE LOAD 1x 107 5 x 105 1 x 106 3 x 106 5 x 105 1 x 106 3x 106 5 x 105 1 x 106 3 x 106 5 x 105 1x 106 3 x 106 5 x 105 1 x 106 3 x 106 INDUCTIVE LOAD 1 x 107 15 x 104 Maximum Switching Capacity 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 CURRENT 2.0 3 x 105 1 x 106 — — — 15 x 104 3 x 105 15 x 104 3 x 105 1 x 106 15 x 104 3 x 105 1 x 106 1 x 106 AC resistive 1.0 .9 .8 .7 .6 .5 .4 .3 .2 DC resistive Contact Voltage (V) NOTES: 1. Relays operated at nominal coil voltage. 2. Inductive load tests are at 0.7 power factor. 3. Table represents typical life figures and are not guaranteed minimums. ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-08-22 Junkersstrasse 3, D-82178 Puchheim, Germany 1000 100 10 50 60 70 80 90 20 30 40 400 500 600 700 800 900 200 300 .1 China