AZ833P1S1-24DE

AZ833P MICROMINIATURE POLARIZED LATCHING RELAY FEATURES • Single and dual coil latching versions • High dielectric and surge voltage: 2.5 KV surge (per Bellcore TA–NWT–001089) 1.5 KV surge (per FCC Part 68) 1,000 Vrms, open contacts • Low power consumption: 79 mW pickup • Stable contact resistance for low level signal switching • Epoxy sealed • UL, CUR file E43203 • All plastics meet UL94 V–O, 30 min. oxygen index CONTACTS Arrangement Ratings DPDT (2 Form C) Bifurcated crossbar contacts Resistive load: Max. switched power: 60 W or 62.5 VA Max. switched current: 2.0 A Max. switched voltage: 220 VDC or 250 VAC Rated Load UL/CSA 0.25 A at 240 0.5 A at 125 2.0 A at 30 0.3 A at 110 VAC VAC VDC VDC GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (set) (typical) Release Time (reset) (typical) Bounce (typical) Dielectric Strength (at sea level) Insulation Resistance Minimum operations 1 x 108 1 x 105 at 0.5 A, 125 VAC, resistive 2 x 105 at 1.0 A, 30 VDC, resistive 3 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) At 10 mA contact current 1 ms at operate or release See table 109 ohms min. at 25°C, 500 VDC, 50% RH At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Operational, 35 g, 10–1000 Hz Operational, 50 g min., 11 ms Non-destructive, 150 g min., 11 ms See soldering profile 80°C (176°F) 30 seconds 2.5 grams P.B.T. polyester Tinned copper alloy, P.C. 50 per plastic tube / 1000 per carton box 400 per reel / 2000 per carton box Material Silver nickel gold plated Silver palladium available upon request COIL (Polarized) Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 79 mW (dual coil) 39 mW (single coil) 1.0 W at 20°C (68°F) At nominal coil voltage 18°C (32°F) Max. 110°C (230°F) Ambient Temperature Operating Storage Vibration Shock Max. Solder Temp. Temp./Time Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Relay has fixed coil polarity. 4. Specifications subject to change without notice. Enclosure Terminals Packing unit in pcs THT SMT ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany AZ833P RELAY ORDERING DATA COIL SPECIFICATIONS STANDARD RELAYS: Bistable, 2 coils Nominal Coil VDC 3 4.5 5 6 9 12 24 Set / Reset VDC 2.25 3.38 3.75 4.50 6.75 9.00 18.00 Max. Continuous VDC 6.5 9.8 10.9 13.0 19.6 26.2 52.3 Coil Resistance Ohm ± 10% 64.3 145 178 257 578 1,029 4,114 THT Through Hole AZ833P2–3DE AZ833P2–4.5DE AZ833P2–5DE AZ833P2–6DE AZ833P2–9DE AZ833P2–12DE AZ833P2–24DE Order Number SMT Long AZ833P2S1–3DE AZ833P2S1–4.5DE AZ833P2S1–5DE AZ833P2–6DE AZ833P2S1–9DE AZ833P2S1–12DE AZ833P2S1–24DE SMT Short AZ833P2S2–3DE AZ833P2S2–4.5DE AZ833P2S2–5DE AZ833P2S2–6DE AZ833P2S2–9DE AZ833P2S2–12DE AZ833P2S2–24DE STANDARD RELAYS: Bistable, 1 coil Nominal Coil VDC 3 4.5 5 6 9 12 24 Set / Reset VDC 2.25 3.38 3.75 4.50 6.75 9.00 18.00 Max. Continuous VDC 6.5 9.8 10.9 13.0 19.6 26.2 52.3 Coil Resistance Ohm ± 10% 128 289 357 514 1,157 2,057 8,228 THT Through Hole AZ833P1–3DE AZ833P1–4.5DE AZ833P1–5DE AZ833P1–6DE AZ833P1P1–9DE AZ833P1–12DE AZ833P1–24DE Order Number SMT Long AZ833P1S1–3DE AZ833P1S1–4.5DE AZ833P1S1–5DE AZ833P1S1–6DE AZ833P1S1–9DE AZ833P1S1–12DE AZ833P1S1–24DE SMT Short AZ833P1S2–3DE AZ833P1S2–4.5DE AZ833P1S2–5DE AZ833P1S2–6DE AZ833P1S2–9DE AZ833P1S2–12DE AZ833P1S2–24DE INITIAL DIELECTRIC STRENGTH (minimum) VRMS, 1 min. Between open contacts Between contact sets Between coil and contacts 1,000 1,000 1,800 Peak (V) 1,500 1,500 2,500 SURGE Rise Time (µS) 10 2 2 Decay Time* (9µS) (1/2 peak) 160 160 10 * Decay time measured from beginning of surge. LOAD LIMIT CURVE RECOMMENDED SOLDERING PROFILE Convection Soldering V ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany AZ833P MECHANICAL DATA THT SMT Long Terminals SMT Short Terminals PCB Layout Viewed toward terminals Solder Pad Layout Viewed toward the component side of the PCB Long terminals Short terminals Wiring Diagram Viewed toward terminals + SET – RESET + SET + RESET – + – – Shown in reset position Shown in reset position Viewed toward component side of PCB – SET + RESET + SET – RESET + – – + Shown in reset position All dimensions in mm Shown in reset position ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany AZ833P PACKAGING Tape and reel for SMT version with long terminals – AZ833P1S1 or AZ833P2S1 Tape and reel for SMT version with short terminals – AZ833P1S2 or AZ833P2S2 Tube for THT version – AZ833P1 or AZ833P2 All dimensions in mm ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany