AZ851-12

AZ851 MICROMINIATURE POLARIZED RELAY FEATURES • Microminiature size: Height: .244 inches (6.2 mm); Length: .559 inches (14.2 mm); Width: .366 inches (9.3 mm) • High sensitivity, 79 mW pickup • Meets FCC Part 68.302 1500 V lightning surge • Surface mount type with “L” shaped terminals • Monostable and bistable (latching) single coil and two coil versions available • Epoxy sealed • UL, CUR file E43203 CONTACTS Arrangement Ratings DPDT (2 Form C) Bifurcated crossbar contacts Resistive load: Max. Max. Max. Max. switched power: 30 W or 62.5 VA switched current: 1 A switched voltage: 220 VDC* or 250 VAC carry current: 2A special precautions must be taken. Please contact the factory. GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Set Time (bistable versions) Reset Time (bistable versions) Dropout Capacitance Minimum operations 1 x 108 2 x 105 at 1 A, 30 VDC resistive 1 x 105 at 0.5 A, 125 VAC resistive 2 ms at nominal coil voltage 1 ms at nominal coil voltage (with no coil suppression) 2 ms at nominal coil voltage (typical) Recommended coil pulse: 20 ms 2 ms at nominal coil voltage (typical) Recommended coil pulse: 20 ms Greater than 10% of nominal coil voltage Contact to contact: 0.4 pF Contact set to contact set: 0.2 pF Contact to coil: 0.9 pF 1000 Vrms between contact sets 1000 Vrms across contacts 1000 Vrms contact to coil Meets FCC part 68.302 1500 V lightning surge 1000 megohms min. at 25°C, 500 VDC, 50% RH At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) .130" (3.3 mm) DA at 10–55 Hz 50 g LCP Tinned copper alloy, P.C. 80°C (176°F) 30 seconds 1.5 grams 25 per plastic tube / 1000 per carton box 500 per reel * Note: If switching voltage is greater than 30 VDC, Rated Load UL, CUR Material Resistance 1 A at 30 VDC resistive 0.5 A at 125 VAC resistive Silver palladium, gold clad < 50 milliohms initially COIL (Polarized) Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature Single side stable: 79–169 mW Bistable (latching) single coil: 56–84 mW Bistable (latching) two coil: 113–169 mW 875 mW at 20°C (68°F) ambient 18°C (32°F) at nominal coil voltage Max. 105°C (221°F) Dielectric Strength (at sea level) Insulation Resistance Ambient Temperature Operating Storage Vibration NOTES 1. 2. 3. 4. All values at 20°C (68°F). Relay has fixed coil polarity. Relay may pull in with less than “Must Operate” value. Relay adjustment may be affected if undue pressure is exerted on relay case. 5. For complete isolation between the relay’s magnetic fields, it is recommended that a .197" (5.0 mm) space be provided between adjacent relays. 6. Specifications subject to change without notice. Shock Enclosure Terminals Max. Solvent Temp. Max. Immersion Time Weight Packing unit in pcs (TR Tape & Reel) ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany AZ851 RELAY ORDERING DATA COIL SPECIFICATIONS Standard Coil: Monostable Nominal Coil VDC 3 5 6 9 12 24 48 * Not UL Approved Must Operate VDC 2.25 3.75 4.5 6.75 9.0 18.0 36.0 Max. Continuous VDC 7.5 12.5 15.0 22.5 30.0 48.0 80.0 Coil Resistance Ohm ± 10% 64.3 178 257 579 1,028 2,880 7,680 ORDER NUMBER AZ851–3 AZ851–5 AZ851–6 AZ851–9 AZ851–12 AZ851–24 AZ851-48 * Bistable (Latching): 1 Coil Nominal Coil VDC 3 5 6 9 12 24 Set-/Reset VDC 2.25 3.75 4.5 6.75 9.0 18.0 Max. Continuous VDC 8.7 14.5 17.4 26.1 34.8 57.6 Coil Resistance Ohm ± 10% 90 250 360 810 1,440 3,840 ORDER NUMBER AZ851P1–3 AZ851P1–5 AZ851P1–6 AZ851P1–9 AZ851P1–12 AZ851P1–24 Bistable (Latching): 2 Coils Nominal Coil VDC 3 5 6 9 12 24 Set-/Reset VDC 2.25 3.75 4.5 6.75 9.0 18.0 Max. Continuous VDC 6.0 10.0 12.0 18.0 24.0 40.0 Coil Resistance Ohm ± 10% 45 125 180 405 720 1,920 ORDER NUMBER AZ851P2–3 AZ851P2–5 AZ851P2–6 AZ851P2–9 AZ851P2–12 AZ851P2–24 MECHANICAL DATA .559 [14.2] .366 [9.3] PC BOARD LAYOUT 2x.027 [0.69] 2x.035 [0.89] 10x.040 [1.0] 10x.118 [3.0] .244 [6.2] .076 [1.92] .100 [2.54] .100 [2.54] .100 [2.54] B A A B .030 [0.75] .020 TYP [0.5] .100 [2.54] .008 [0.2] .300 [7.62] .453 [11.5] 3˚ TYP STAND-OFF A & B .258 [6.56] 4x.079 [2.01] .080 [2.02] 4x.100 [2.54] WIRING DIAGRAMS SINGLE SIDE STABLE BISTABLE (LATCHING) TWO COIL 1 (+) 2 3 4 5 2x.024 [0.61] 2x.047 [1.19] 1 (+) 2 3 4 5 Set Coil (-) Stripe on top of relay indicates the position of pins 1 & 10 (-) (+) Diagrams show the "reset" position before energized with polarity as shown. SOLDERING PADS FOR TERMINALS TEMPORARY GLUE PADS FOR STAND-OFFS A OR B (-) 10 9 8 7 6 10 9 8 7 6 Reset Coil DEENERGIZED OR RESET CONDITION Watch for polarity RESET CONDITION Watch for polarity VIEWED TOWARDS TERMINALS VIEWED TOWARDS TERMINALS Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany AZ851 Soldering Data Tape Dimensions IRS (Infrared Reflow Soldering) .015 [0.38] \U+2205.059 [\U+22051.5] .158 [4.0] .069 [1.75] TEMPERATURE (˚C) T3 SOLDERING T 3= 245˚C MAX .393 [10.0] .571 [14.5] .945 [24.0] T2 PREHEATING T1 COOLING T 2= 200˚C MAX T 1 150˚C MAX = .260 [6.6] .510 [13.0] .630 [16.0] 90 SEC MAX 30 SEC MAX VPS (Vapor Phase Soldering) Packaging TEMPERATURE (˚C) 215 C MAX SOLDERING T 3= 215˚C MAX T2 = 200˚C MAX T 1 150˚C MAX = COOLING T2 PREHEATING T1 T3 ORIENTATION MARK SIDE FEEDING 60 SEC MAX 60 SEC MAX Reel Dimensions .984 [25.0] INSIDE WIDTH TOP COVER TAPE t=.002 [0.06] ø13.0 [ø330] EMBOSSED CARRIER TAPE t=.016 [0.4] ø.512 [ø13.0] ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2005-08-04 Junkersstrasse 3, D-82178 Puchheim, Germany