AZ9371-1AE-5DE

AZ9371 SENSITIVE SUBMINIATURE RELAY FEATURES • Extremely small footprint • Thin vertical profile only 0.275" (7 mm) wide • High sensitivity, 113 mW pickup • Dielectric strength 4000 Vrms • 5 Amp switching capability (version “T” 10 Amp) • Two different footprints available • Class B insulation (130°C) standard, Class F (155°C) available • UL, CUR file E44211 • VDE 40030746 GENERAL DATA CONTACTS Arrangement Ratings SPST (1 Form A) Resistive load: Max. switched power: (Version “T”: Max. switched current: (Version “T”: Max. switched voltage: 150 W or 1385 VA 300 W or 2770 VA) 5A 10 A) 30 VDC* or 277 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL/CSA VDE 5 A at 277/250/125 VAC General Use 50k cycles 85°C [1][2] 5 A at 30 VDC General Use 50k cycles 85°C [1][2] 3 A at 277/250/125 VAC General Use 120k cycles 85°C [1][2] 3 A at 30 VDC General Use 120k cycles 85°C [1][2] B300 Pilot Duty 120/240 VAC 25k cycles [2] R300 Pilot Duty 125/250 VAC 25k cycles [2] "T" Version 10 A at 277/250/125 VAC General Use 10k cycles 85°C [1][2] 10 A at 30 VDC General Use10k cycles 85°C [1][2] 7 A at 277/250/125 VAC General Use 60k cycles 85°C [2] 7 A at 277/250/125 VAC General Use 50k cycles 105°C [1] 7 A at 30 VDC General Use, 50k cycles 105°C [1] 7 A at 30 VDC General Use, 60k cycles 85°C [2] TV-3, 25k cycles 5 A at 250 VAC / 30 VDC [1][2] 10 A at 250VAC / 30 VDC (T version) Life Expectancy Mechanical Standard version Electrical Minimum operations 5 million operations 1 X 105 at 5 A, 250 VAC res. [1] 5 X 104 at 5 A, 250 VAC res. [2] High capacity version “T” 1 X 105 at 7 A, 250 VAC res. [1] Electrical 1 X 104 at 10 A, 250 VAC res. [1][2] 3 X 104 at 7 A, 250 VAC res. [2] Operate Time (typical) 10 ms at nominal coil voltage Release Time (typical) 10 ms at nominal coil voltage (with no coil suppression) Dielectric Strength (at sea level for 1 min.) 4000 Vrms coil to contact 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 10 g Material Silver nickel [1], silver tin oxide [2], gold plating available Enclosure P.B.T. polyester Resistance < 100 milliohms initially (at 6 V, 1 A, voltage drop method) Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 3 grams COIL Power At Pickup Voltage (typical) 113 mW Max. Continuous Dissipation 750 mW at 20°C (68°F) ambient Temperature Rise 26°C (47°F) at nominal coil voltage ) 1. All values at 20°C (68°F). Temperature Max. 130°C (266°F) Class B Max. 155°C (311°F) Class F 2. Relay may pull in with less than “Must Operate” value. NOTES 3. Specifications subject to change without notice. AZ9371 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC Must Operate VDC Max. Continuous VDC Coil Resistance Ohm ± 10% 3 2.25 3.9 45 AZ9371-1A-3D 5 3.75 6.5 125 AZ9371-1A-5D 6 4.50 7.8 180 AZ9371-1A-6D 9 6.75 11.7 405 AZ9371-1A-9D 12 9.00 15.6 720 AZ9371-1A-12D 18 13.50 23.4 1620 AZ9371-1A-18D 24 18.00 31.2 2880 ORDER NUMBER AZ9371-1A-24D *Add "T" after "AZ9371" for high capacity version. Add “E" after "1A" to indicate silver tin oxide contacts. Add suffix "E" for sealed version. Add suffix “K” for K version footprint. Add suffix “F” for Class F version. Add suffix “G” at the end of order number for gold plated contacts. 3/20/18 AZ9371 MECHANICAL DATA Standard Pinning Outline Dimensions Version"K" Pinning Outline Dimensions 0.3 0.3 + 0.15 - 0.1 + 0.15 - 0.1 0.8 Ø 0.4 - 0.05 + 0.2 11.5 7.0 15 .3 ± 0.3 3.4 ± 0.3 0.3 3.4 ± 0.3 0.3 15 .3 ± 0.3 7.2 max 20.5 max 7.2 max 20.5 max 0.3 0.3 + 0.15 - 0.1 4.7 3.5 PC BOARD LAYOUT + 0.15 - 0.1 0.8 Ø 0.4 - 0.05 + 0.2 15 4.7 PC BOARD LAYOUT 7 4.7 4 x ø 1.1 4.7 4 x ø 1.1 3.5 11.5 15 Viewed toward terminals Viewed toward terminals WIRING DIAGRAM WIRING DIAGRAM 13 7 5 1 Viewed toward terminals 5 7 13 1 Viewed toward terminals Attention! Grid is not 0.1” (2.54 mm)!! 3/20/18