eZ80Acclaim!™/
eZ80AcclaimPlus!™
Ethernet Modules
Product Specification
PS030603-1013
Copyright ©2013 Zilog®, Inc. All rights reserved.
www.zilog.com
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
ii
Warning: DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
AS USED HEREIN
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A
critical component is any component in a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
DOCUMENT DISCLAIMER
©2013 Zilog, Inc All rights reserved. Information in this publication concerning the devices, applications,
or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES
NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE
INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED
IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED
HEREIN OR OTHERWISE. The information contained within this document has been verified according
to the general principles of electrical and mechanical engineering.
eZ80Acclaim!™ and eZ80AcclaimPlus!™ are trademarks or registered trademarks of Zilog, Inc., an IXYS
Company. All other product or service names are the property of their respective owners.
PS030603-1013
Disclaimer
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
iii
Revision History
Each instance in the following revision history table reflects a change to this document
from its previous version. For more details, refer to the corresponding pages or appropriate
links provided in the table.
Revision
Level
Description
Page
Number
Oct
2013
03
Corrected erroneous part number listed f or the eZ80AcclaimPlus!
Development Kit, Ordering Information chapter.
17
May
2013
02
Updated to include ordering information for the eZ80F915150MODG and
eZ80F917150MODG parts.
17
Mar
2013
01
Original issue.
All
Date
PS030603-1013
Revision History
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
iv
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
eZ80Acclaim!™/eZ80AcclaimPlus!™ MCU Features . . . . . . . . . . . . . . . . . . . . . . . .
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
3
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Peripheral Bus Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Input/Output Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Onboard Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logic-Level Input/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Onboard Battery Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet PHY and RJ45 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast Buffer (U6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Interface Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
12
12
12
12
14
15
15
16
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PS030603-1013
Table of Contents
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
v
List of Figures
Figure 1.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Functional Block
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 2.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Peripheral Bus
Connector: J1 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 3.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Input/Output
Connector: J2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 4.
Bus Contention without the eZ80Acclaim!™/eZ80AcclaimPlus!™
Ethernet Module: Fast Buffer Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 5.
Physical Dimensions of the eZ80Acclaim!™/eZ80AcclaimPlus!™
Ethernet Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 6.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic
Diagram: Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 7.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic
Diagram: SRAM and Flash Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 8.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic
Diagram: J1 and J2 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 9.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic
Diagram: MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PS030603-1013
List of Figures
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
vi
List of Tables
Table 1.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Peripheral Bus:
Connector Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 2.
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Input/Output
Connector: Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 3.
Flash Memory Programming Signals and Jumpers . . . . . . . . . . . . . . . . . . . 14
Table 4.
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 5.
Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PS030603-1013
List of Tables
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
eZ80Acclaim!™/eZ80AcclaimPlus!™
Ethernet Modules
Zilog’s eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules are compact, high-performance devices specially designed for the rapid development and deployment of embedded
systems requiring control and internet/intranet connectivity.
These expandable modules are powered by Zilog’s power-efficient, optimized-pipelinearchitecture eZ80F91 MCU, a member of Zilog’s eZ80AcclaimPlus!™ family. The
eZ80F91 MCU is a high-speed, single-cycle instruction-fetch microcontroller that operates with a clock speed of 50 MHz. It can also operate in Z80®-compatible addressing
mode (64 KB) or full 24-bit addressing mode (16 MB).
The rich peripheral set of these eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
make them suitable for a variety of applications, including industrial control, communication, security, automation, point-of-sale terminals, and embedded networking applications.
Features
Zilog’s eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules offer the following features:
•
•
•
•
•
•
•
Factory-default operating clock frequency at 50 MHz
•
Onboard connector provides I/O bus for external peripheral connections (IRQ, CS, 24
address, 8 data)
•
•
•
•
Low-cost connection to carrier board via two 2x30 pin headers
PS030603-1013
10/100 Base-T Ethernet PHY with RJ45 connector
512 KB off-chip fast SRAM
8 MB off-chip NOR Flash memory
32 Mbit serial Flash memory with SPI interface
Battery for on-chip Real-Time Clock
Input/Output connector (J2) which provides 32 general-purpose 5 V-tolerant I/O pinouts
Small footprint 63.5 mm x 78.7 mm
3.3 V power supply
Standard operating temperature range: 0ºC to +70ºC
1
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
eZ80Acclaim!™/eZ80AcclaimPlus!™ MCU Features
The eZ80Acclaim!™/eZ80AcclaimPlus!™ MCUs offer the following features:
•
•
•
•
Single-cycle instruction fetch, high-performance, pipelined eZ80® CPU core
•
•
•
•
•
•
Two UARTs with independent baud rate generators and support for 9-bit operation
•
•
Flexible-priority vectored interrupts (both internal and external) and interrupt controller
•
•
•
•
•
•
•
Four 16-bit Counter/Timers with prescalers and direct input/output drive
PS030603-1013
256 KB of Flash memory and 8 KB of SRAM
10/100 Mbps Ethernet MAC with 8 KB frame buffer
Low power features including SLEEP Mode, HALT Mode, and selective peripheral
power-down control
SPI with independent clock generator
I2C with independent clock generator
Infrared data association (IrDA)-compliant infrared encoder/decoder
New DMA-like eZ80 instructions for efficient block data transfer
External interface with four chip selects, individual wait state generators, and an external WAIT input pin; supports Intel- and Motorola-style buses
Real-time clock with on-chip 32 kHz oscillator, selectable 50/60 Hz input, and separate
VDD pin for battery backup
Watchdog Timer (WDT)
32 bits of general-purpose input/output (GPIO)
JTAG and ZDI debug interfaces
144-pin BGA or 144-pin LQFP package
Supply voltage of 3.0 V to 3.6 V with 5 V-tolerant inputs
Standard operating temperature range: 0 ºC to +70 ºC
2
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Block Diagram
32 kHz
XTAL
GPIO
eZ80Acclaim! &
eZ80AcclaimPlus!
Control and Address Bus
eZ80F91 MCU
50 MHz
XTAL
External
Peripheral
Bus (JP2)
Battery
External GPIO
Bus (JP2)
Figure 1 presents a block diagram of the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet
Module.
MII
SPI
Data Bus
IS1894K-40
8 MB Flash
(CS0)
Fast Buffer
Ethernet
CS0
NAND Flash
(32Mb)
512 KB SRAM
(CS1)
Figure 1. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Functional Block Diagram
PS030603-1013
3
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Pin Description
This chapter describes each pin and its signal direction for each of the eZ80Acclaim!™/
eZ80AcclaimPlus!™ Ethernet Module’s Peripheral Bus and GPIO connectors.
Peripheral Bus Connector
Figure 2 presents a pin layout of the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules’ 60-pin Peripheral Bus Connector (J1). Table 1 lists the pins and their functions.
J1
TRSTNF91_WE-
TRSTNF91_WE-
A6
A10
A8
A13
A15
A18
A19
A2
A11
A4
A5
CS0CS2-
MREQWRBUSACK-
A21
A22
CS0CS2D1
D3
D5
D7
MREQGND
WRBUSACK-
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
VCC_3v3
A0
A3
A7
A9
A14
A16
A1
A12
A20
A17
DIS_FLASHA23
CS1D0
D2
D4
DIS_FLASHCS1-
GND
D6
IOREQRDINSTRDBUSREQ-
IORQRDINSTRDBUSREQ-
HDR/PIN 2x30
GND
Figure 2. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Peripheral Bus Connector:
J1 Pin Configuration
PS030603-1013
4
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Note: All signals with an overline are active Low. For example, B/W, in which WORD is active
Low, and B/W, in which BYTE is active Low.
Table 1. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Peripheral Bus:
Connector Pin Identification
Pin No Symbol
Pull Up/
Down
Signal Direction Comments
1
Reserved
2
Reserved
3
Reserved
4
Reserved
5
TRSTN
6
Reserved
7
F91_WE
8
Reserved
9
GND
VSS/Ground (0 V).
10
VCC
3.3 V supply input pin.
11
A6
Bidirectional
12
A0
Bidirectional
13
A10
Bidirectional
14
A3
Bidirectional
15
GND
VSS/Ground (0 V).
16
VCC
3.3 V supply input pin.
17
A8
Bidirectional
18
A7
Bidirectional
19
A13
Bidirectional
20
A9
Bidirectional
21
A15
Bidirectional
22
A14
Bidirectional
PU 10 kΩ
Input
Reset for on-chip instrumentation (OCI).
Input
A Low enables a write to on-chip Flash
memory. If this pin is unconnected, on-chip
Flash memory is write-protected.
Notes:
1. External capacitive loads on RD, WR, IORQ, MREQ, D0–D7, and A0–A23 must be below 10 pF to satisfy timing
requirements for the CPU.
2. All unused inputs must be pulled to either VDD or GND, depending on their inactive levels, to reduce power
consumption and to reduce noise sensitivity.
3. All inputs are CMOS level 3.3 V (5 V-tolerant), except where otherwise noted.
PS030603-1013
5
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Table 1. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Peripheral Bus:
Connector Pin Identification (Continued)
Pin No Symbol
Pull Up/
Down
Signal Direction Comments
23
A18
Bidirectional
24
A16
Bidirectional
25
A19
Bidirectional
26
GND
27
A2
Bidirectional
28
A1
Bidirectional
29
A11
Bidirectional
30
A12
Bidirectional
31
A4
Bidirectional
32
A20
Bidirectional
33
A5
Bidirectional
34
A17
Bidirectional
35
Reserved
36
DIS_FLASH
37
A21
38
VCC
39
A22
Bidirectional
40
A23
Bidirectional
41
CS0
Output
42
CS1
Output
43
CS2
Output
44
D0
PU 4 kΩ
Bidirectional
45
D1
PU 4 kΩ
Bidirectional
46
D2
PU 4 kΩ
Bidirectional
47
D3
PU 4 kΩ
Bidirectional
48
D4
PU 4 kΩ
Bidirectional
VSS/Ground (0 V).
PU 10 kΩ
Input
A Low disables onboard Flash memory.
Flash is enabled if DIS_FLASH is not
connected; CMOS input 3.3 V (5 V-tolerant).
Bidirectional
3.3 V supply input pin.
Notes:
1. External capacitive loads on RD, WR, IORQ, MREQ, D0–D7, and A0–A23 must be below 10 pF to satisfy timing
requirements for the CPU.
2. All unused inputs must be pulled to either VDD or GND, depending on their inactive levels, to reduce power
consumption and to reduce noise sensitivity.
3. All inputs are CMOS level 3.3 V (5 V-tolerant), except where otherwise noted.
PS030603-1013
6
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Table 1. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Peripheral Bus:
Connector Pin Identification (Continued)
Pin No Symbol
Pull Up/
Down
Signal Direction Comments
49
D5
PU 4 kΩ
Bidirectional
50
GND
51
D7
52
D6
Bidirectional
53
MREQ
Bidirectional
54
IORQ
Bidirectional
55
GND
56
RD
Bidirectional
57
WR
Bidirectional
58
INSTRD
Output
59
BUSACK
Output
60
BUSREQ
VSS/Ground (0 V).
PU 4 kΩ
Bidirectional
VSS/Ground (0 V).
PU 2 kΩ
Input
Notes:
1. External capacitive loads on RD, WR, IORQ, MREQ, D0–D7, and A0–A23 must be below 10 pF to satisfy timing
requirements for the CPU.
2. All unused inputs must be pulled to either VDD or GND, depending on their inactive levels, to reduce power
consumption and to reduce noise sensitivity.
3. All inputs are CMOS level 3.3 V (5 V-tolerant), except where otherwise noted.
Input/Output Connector
Figure 3 presents a pin layout of the 60-pin I/O connector (J2) of the modules. However,
the eZ80® Development Platform features a 50-pin connector. eZ80Acclaim!™/
eZ80AcclaimPlus!™ Ethernet Modules are designed to interface pin 60 of their J2 connectors to pin 50 of the eZ80 Development Platform’s JP2 connector so that pins 1–10 of the
Modules overlap the edge of the eZ80 development platform. Table 2 describes the pins.
PS030603-1013
7
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
J2
PA7
PA5
PA3
PA1
PB7
PB5
PB3
PB1
PC6
PC4
PC2
PC0
PD6
PD5
PD3
PD1
TDO
TCK
RTC_VDD
IICSCL
IICSDA
FLASH_WECS3RESETHALT_SLP-
PA7
PA5
PA3
PA1
VCC_3V3
PB7
PB5
PB3
PB1
PC6
PC4
PC2
PC0
PD6
PD5
PD3
PD1
TD0
GND
TCK
RTC_VDD
IICSCL
IICSDA
FLASH_WECS3RESETHALT_SLP-
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
PA6
PA4
PA2
PA0
PB6
PB4
PB2
PB0
PC7
PC5
PC3
PC1
PD7
PD4
PD2
PD0
TDI
TRIGOUT
TMS
EZ80CLK
PA6
PA4
PA2
PA0
PB6
PB4
PB2
PB0
PC7
PC5
PC3
PC1
PD7
PD4
PD2
PD0
TDI
TRGOUT
TMS
EZ80CLK
GND
WAITNMI-
WAITNMI-
HDR/PIN 2x30
VCC_3v3
VCC_3v3
VCC_3v3
Figure 3. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Input/Output Connector:
J2 Pin Configuration
PS030603-1013
8
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Table 2. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Input/Output Connector:
Pin Identification
Pin No Symbol
Pull Up/
Down
Signal Direction Comments
1
PA7
Bidirectional
2
PA6
Bidirectional
3
PA5
Bidirectional
4
PA4
Bidirectional
5
PA3
Bidirectional
6
PA2
Bidirectional
7
PA1
Bidirectional
8
PA0
Bidirectional
9
VCC
3.3 V supply input pin.
10
GND
VSS/Ground (0 V).
11
PB7
Bidirectional
12
PB6
Bidirectional
13
PB5
Bidirectional
14
PB4
Bidirectional
15
PB3
Bidirectional
16
PB2
Bidirectional
17
PB1
Bidirectional
18
PB0
Bidirectional
19
GND
20
PC7
Bidirectional
21
PC6
Bidirectional
22
PC5
Bidirectional
23
PC4
Bidirectional
24
PC3
Bidirectional
25
PC2
Bidirectional
26
PC1
Bidirectional
27
PC0
Bidirectional
VSS/Ground (0 V).
Notes:
1. External capacitive loads on RD, WR, IORQ, MREQ, D0–D7, and A0–A23 must be below 10 pF to satisfy timing
requirements for the CPU.
2. All unused inputs must be pulled to either VDD or GND, depending on their inactive levels, to reduce power
consumption and to reduce noise sensitivity.
3. All inputs are CMOS level 3.3 V (5 V-tolerant), except where otherwise noted.
PS030603-1013
9
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Table 2. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Input/Output Connector:
Pin Identification (Continued)
Pin No Symbol
Pull Up/
Down
Signal Direction Comments
28
PD7
Bidirectional
29
PD6
Bidirectional
30
GND
31
PD5
32
PD4
33
PD3
Bidirectional
34
PD2
Bidirectional
35
PD1
Bidirectional
36
PD0
Bidirectional
37
TDO
Output
JTAG Data Output pin.
38
TDI/ZDA
Input
JTAG Data Input pin.
39
GND
40
TRIGOUT
41
TCK/ZCL
42
TMS
43
RTC_VDD
44
EZ80CLK
2
45
I C SCL
46
GND
2
47
I C SDA
48
GND
49
FLASHWE
50
GND
VSS/Ground (0 V).
Bidirectional
PD 4 kΩ
Bidirectional
VSS/Ground (0 V).
Output
Active High trigger event indicator.
PU 10 kΩ
Input
JTAG Input. High on reset enables ZDI Mode; Low
on reset enables OCI debug.
PU 10 kΩ
Input
JTAG Test Mode Select Input.
RTC supply. For proper operation of the Modules,
this pin must be connected to the same power
source that powers the module (as it is done on the
Zilog® development platform).
PU 4 kΩ
Output
Synchronous CPU clock output.
Bidirectional
I2C Bus Clock.
VSS/Ground (0 V).
PU 4 kΩ
PU 10 kΩ
Bidirectional
I2C Data Clock.
Power
VSS/Ground (0 V).
Input
A Low enables a write to external Flash memory
boot block area. If this pin is unconnected, the
Flash memory boot block area is write-protected.
VSS/Ground (0 V).
Notes:
1. External capacitive loads on RD, WR, IORQ, MREQ, D0–D7, and A0–A23 must be below 10 pF to satisfy timing
requirements for the CPU.
2. All unused inputs must be pulled to either VDD or GND, depending on their inactive levels, to reduce power
consumption and to reduce noise sensitivity.
3. All inputs are CMOS level 3.3 V (5 V-tolerant), except where otherwise noted.
PS030603-1013
10
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Table 2. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module Input/Output Connector:
Pin Identification (Continued)
Pin No Symbol
51
CS3
52
DIS_IRDA
53
Pull Up/
Down
Signal Direction Comments
Output
Used on the eZ80190, eZ80L92, eZ80F92,
eZ80F93 devices and connected to the CS8900
EMAC.
PU 10 kΩ
Input
A Low disables the onboard IRDA transceiver to
use PC0/PC1 UART pins externally.
RESET
PU 2 kΩ
Bidirectional
Reset Output from module or push-button reset.
54
WAIT
PU 2 kΩ
Input
Driving the WAIT pin Low forces the CPU to
provide additional clock cycles for an external
peripheral or external memory to complete its read
or write operation.
55
VCC
3.3 V supply input pin.
56
GND
VSS/Ground (0 V).
57
HALT_SLP
58
NMI
59
VCC
60
Reserved
Output, Active
Low
PU 10 kΩ
A Low on this pin indicates that the CPU enters
either HALT or SLEEP Mode because of execution
of either a HALT or SLP instruction.
Schmitt-trigger
The NMI input is a higher priority input than the
Input, Active Low maskable interrupts. It is always recognized at the
end of an instruction, regardless of the state of the
interrupt enable control bits. This input includes a
Schmitt-trigger to allow RC rise times. This
external NMI signal is combined with an internal
NMI signal generated from the WDT block before
being connected to the NMI input of the CPU.
3.3 V supply input pin.
NC
Reserved; no connection.
Notes:
1. External capacitive loads on RD, WR, IORQ, MREQ, D0–D7, and A0–A23 must be below 10 pF to satisfy timing
requirements for the CPU.
2. All unused inputs must be pulled to either VDD or GND, depending on their inactive levels, to reduce power
consumption and to reduce noise sensitivity.
3. All inputs are CMOS level 3.3 V (5 V-tolerant), except where otherwise noted.
PS030603-1013
11
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Onboard Component Description
This chapter describes each individual component of the eZ80Acclaim!™/
eZ80AcclaimPlus!™ Ethernet Module.
Logic-Level Input/Outputs
The I/O connector features 32 general-purpose 3.3 V CMOS I/O pins that can be used as outputs or inputs interfacing to external logic. All I/Os are 5 V-tolerant. Some of the general-purpose I/O pins support dual mode functions (SPI, Timer I/O, UARTs, and bit I/O with edge- or
level-triggered interrupt functions on each pin). For more information about the
eZ80Acclaim!™ MCU, refer to the eZ80F91 MCU Product Specification (PS0192). To learn
more about the eZ80AcclaimPlus!™ MCU, refer to the eZ80F91 ASSP Product Specification
(PS0270).
Onboard Battery Backup
An onboard Panasonic ML2020 3 V Lithium battery powers the 32 kHz real-time clock
when external power is removed. The battery is charged through diode D2 and resistor
R17 when external power is applied to the board.
Ethernet PHY and RJ45 Connector
The Module is equipped with an RJ45 connector with integrated magnetics and two LEDs
manufactured by IDT.
Ethernet LEDs
Ethernet activity is indicated by two LEDs located on the RJ45 connector. When the PHY
is receiving data, the green LED is ON. When the PHY is transmitting data, the yellow
LED is ON.
Fast Buffer (U6)
The eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module features a fast buffer (see Figure 1 on page 3) that is used to prevent bus contention that can occurs due to slow turn-off
time of the module’s external Flash memory, and the fast bus turn-around time of the
PS030603-1013
12
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
eZ80F91 MCU (i.e, a generic feature of the eZ80® family when it is used in NATIVE
Mode).
When developing with the eZ80 family of products in NATIVE Mode, the challenge with
bus contention occurs when two or more devices drive a common bus. The eZ80F91
MCU’s CS0 drives the Flash CE. After accessing the Flash memory space, CS0 is driven
High a maximum of 8.8 ns after the next rising edge of the clock (refer to T6 in Figure 4).
The Flash turn-off time (TOD) is 25 ns, which is the period from OE or CE going High to
the Flash output drivers going into High-Z Mode. In essence, after the end of the MCU’s
read access to Flash, a period of 8.8 ns + 25 ns = 33.8 ns must occur before Flash memory
stops driving the data bus. At this point, the eZ80F91 device is already well into the next
bus cycle.
T6
Clock
T3
-CS0
F91 Data
Bus
Data IN
Data OUT
-RD
Bus contention
Tod
FLash
Data Bus
-CS1
-WR
T4
Figure 4. Bus Contention without the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module:
Fast Buffer Feature
During a memory write cycle, data (output) from the eZ80F91 device is valid not later
than T3 = 7.5 ns, and the write pulse is asserted not later than 4.5 ns after the falling edge
of the Clock (14.5 ns from the rising edge if Clock is 50 MHz). The result is that during
TCON = (33.8 ns – 7.5 ns) = 26.3 ns, two devices drive the common data bus: the eZ80F91
MCU itself, and Flash memory. In turn, data that is being written during the write opera-
PS030603-1013
13
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
tion could become corrupted. The part used to isolate a slow Flash data bus from a fast
eZ80F91 bus has a 5.5 ns turn-off time, which reduces the 25 ns duration of the TCON to
5.5 ns. As a result, bus contention still occurs, but its duration is not 26.3 ns, as described in
the following equation:
Time of contention = (8.8 ns – 7.5 ns + 5.5 ns = 6.8 ns
Data being written is not corrupted because the write pulse is not yet asserted.
For more information about bus contention on the eZ80Acclaim!™ MCU, refer to the eZ80F91
MCU Product Specification (PS0192). To learn more about bus contention on the
eZ80AcclaimPlus!™ MCU, refer to the eZ80F91 ASSP Product Specification (PS0270).
Memory
The Module’s onboard memory consists of the following components:
•
•
•
U4, CY7C1049: 512 KB SRAM with a 10 ns access time
U5, S29GL064N: 8 MB NOR Flash with 90 ns access time
U3, S25FL032: 32 Mb NAND Flash with an SPI interface
The Module contains external Flash memory, and the eZ80F91 MCU contains internal Flash
memory. To allow read/write access to Flash memory on the Module, there are two signals
provided, on connectors J1 and J2. A jumper on the module, JP3, enables the programming of
on-chip Flash. There is also a signal that duplicates the function of this JP3 jumper. Table 3
indicates the states of the signals and the status of the JP3 jumper for different modes.
Table 3. Flash Memory Programming Signals and Jumpers
Signal/Jumper
Function
State/Status
DIS_FLASH
Controls read/write access to the eZ80Acclaim!™/
eZ80AcclaimPlus!™ Ethernet Module for external Flash memory.
Controls write operations to the boot block of the eZ80Acclaim!™/
™ Ethernet Module for external Flash memory.
When Low,
access is enabled
JP3
Controls write access to eZ80F91 MCU on-chip Flash memory.
When IN, write is
enabled
F91_WE
Controls write access to eZ80F91 MCU on-chip Flash memory.
When Low, write
is enabled
FLASHWE
eZ80AcclaimPlus!
When Low, write
is enabled
The external Flash memory space of the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet
Module has an access time of 90 ns. At least five wait states must be added to the cycle
when accessing external Flash at 50 MHz clock speed. The eZ80F91 devices on-chip Flash
PS030603-1013
14
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
is faster; its minimum access time is 60 ns, which requires only three wait states at
50 MHz.
The Modules feature 512 KB of fast SRAM. Access time is 10 ns, which requires onewait-state access. The eZ80F91 MCU’s on-chip SRAM is used with zero wait states. An
additional memory component on the Module is NAND Flash memory with an SPI interface. This 32 Mb device is manufactured by Spansion.
Serial Interface Ports
The CPU contains two UARTs with programmable baud rate generators. UART0 is connected to GPIO PD[0:7] on the I/O connector. UART1 is connected to GPIO PC[0:7] on
the I/O connector.
Note: Do not connect an RS-232 interface without level shifters. There are no RS-232 level
shifters on the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module.
Physical Dimensions
The footprint of each Modules’ PCB is 63.5 mm x 78.7 mm. With an RJ-45 Ethernet connector, the overall height is 25 mm, see Figure 5.
PS030603-1013
15
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Figure 5. Physical Dimensions of the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module
Absolute Maximum Ratings
Stresses greater than those listed in Table 4 causes permanent damage to the device. These
ratings are stress ratings only. Operation of the device at any condition outside those indicated in the operational sections of these specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability. For improved
reliability, unused inputs must be tied to one of the supply voltages (VDD or VSS).
Table 4. Absolute Maximum Ratings
Parameter
Standard operating temperature
Minimum Maximum
Units
0
+70
ºC
Storage temperature
–45
+85
ºC
Operating Humidity (RH @ 50 ºC)
25%
90%
—
3.6
Operating Voltage
PS030603-1013
V
16
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Ordering Information
You can order your eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module from Zilog or
any of Zilog’s authorized distributors using the following part numbers. For more information about ordering, please consult your local Zilog sales office. The Zilog website lists
all regional offices and provides additional information about the ZMOTION® Detection
Module II product line.
Part Numbers
Table 5 lists the part numbers for the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module products and kit, and briefly describes each part.
Table 5. Part Numbers
Part Number
Description
eZ80F915150MODG
eZ80Acclaim! Ethernet Module
eZ80F917150MODG
eZ80AcclaimPlus! Ethernet Module
eZ80F910300ZCOG
eZ80AcclaimPlus! Development Kit
PS030603-1013
17
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Schematic Diagrams
Figures 6 through Figure 10 displays the layout of the eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Module.
VCC_3v3
VCCIO
L2
1
HZ0805
C27
22uF
C28
+
0.1uF
2
L3
HZ0805
VCCC
VCC_3v3
1
1
VCC_3v3
R22
1 ohm
C29
3.3V_FLT
C32
0.01uF
AMDIX
35
34
33
30
29
25
MII_TXD3
MII_TXD2
MII_TXD1
MII_TXD0
MII_TXEN
MII_TXER
C35
C36
0.01uF
0.01uF
TXD3
TXD2
TXD1
TXD0
TXEN
TXER
15
31
9
R24
18.2K
TCSR
1
MII_TXD[3:0]
GND
GND
U8
4
10
R23
1.82K
VCCIO
VCCC
GND
8
5
0.01uF
VCCC
0.1uF
VCC
VCC
0.1uF
3.3V_FLT
2
2
C34
VCCIO
C31
0.1uF
22uF
C33
C30
+
C37
C38
27pF Y3
27pF
25.000MHZ
REF_IN
REF_OUT
TP_AP
37
36
R25
49.9
C40
C41
0.1uF
0.1uF
100pF 100pF
2
C42
P1
3
R26
TP_AN
C39
TD+
5
49.9
3
CT_T
4
R27
17
MII_CRS
16
MII_COL
MII_RXD[3:0]
18
19
20
22
MII_RXD3
MII_RXD2
MII_RXD1
MII_RXD0
23
27
MII_RXDV
MII_RXER
14
13
MII_MDC
MII_MDIO
24
MII_RST-
R28
COL/Regpin
TP_BP
TP_BN
LED0/P0
RXDV/RMII
RXER/NOD
LED1/P1/ISO
LED2/P4
SPEED
RST
VCCIO
R34
20K
CT_R
8
RD-
1
2
RXD3/AMDIX
RXD2/P3
RXD1/RXTRI
RXD0/FDPX
MDC
MDIO
RD+
6
49.9
7
CRS/HWSW
41
R33
10K 1/8W
11
TXCLK/SPEED
RXCLK/ANSEL
THERMAL_PAD
MII_TXCLK
MII_RXCLK
LED3
LED4/SI
INT/P2
6
AN_1
CAT_1
R29
39
R30
10K
NC
GND_TR
GND_TL
12
11
10K
15
16
TD-
49.9
7
28
26
GUIDE1
GUIDE2
AN_2
CAT_2
GND
9
14
13
10
C43
0.01uF
R35
1 MEG
J3011
40
R31
1K
38
32
21
12
R32
1K
J4
1
VCCIO
HDR/PIN 1x1
ICS1894-40
Figure 6. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic Diagram: Ethernet
PS030603-1013
18
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
U4
A[23:0]
3
4
5
6
7
16
17
18
19
20
26
27
28
29
30
38
39
40
41
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
D[7:0]
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
D0
D1
D2
D3
D4
D5
D6
D7
NC1
NC2
NC3
NC4
NC5
NC6
NC7
NC8
NC9
NC10
VCC1
VCC2
37
15
8
RDWR-
RDWRCS1-
OE
WE
CE
GND1
GND2
9
10
13
14
31
32
35
36
D0
D1
D2
D3
D4
D5
D6
D7
D0
D1
D2
D3
D4
D5
D6
D7
1
2
21
22
23
24
25
42
43
44
A19
VCC_3v3
11
33
12
34
C22
C23
0.1uF
0.1uF
CY7C1049DV33
U6
U5
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
E1
D1
C1
A1
B1
D2
C2
A2
B5
A5
C5
D5
B6
A6
C6
D6
E6
B2
C3
D4
D3
C4
FLASH_CSRDWR-
F1
G1
A4
10K
B4
F6
B3
VCC_3v3
R19
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15/A-1
RY/BY
E2
H2
E3
H3
H4
E4
H5
E5
F2
G2
F3
G3
F4
G5
F5
G6
DF0
DF1
DF2
DF3
DF4
DF5
DF6
DF7
DF0
DF2
DF4
DF6
D7
D5
D3
D1
FLASH_CS-
2
4
6
8
11
13
15
17
1
19
1A1
1A2
1A3
1A4
1B1
1B2
1B3
1B4
2A1
2A2
2A3
2A4
2B1
2B2
2B3
2B4
1OE
2OE
VCC
GND
18
16
14
12
D0
D2
D4
D6
9
7
5
3
DF7
DF5
DF3
DF1
VCC_3v3
20
10
VCC_3v3
C24
SN74CB3Q3244
0.1uF
A0
GND
A3
VCC_3v3
VCC
G4
CE
OE
WE
RST
BYTE
WP
GND1
GND2
C25
C26
0.1uF
0.1uF
H1
H6
S29GL064N
10K
R20
FLASH_WPVCC_3v3
VCC_3v3
U7
1
2
3
CS0U1
DIS_FLASHFLASH_WE-
F91_WP-
1
2
3
4
1A
3Y
2A
GND
VCC
1Y
3A
2Y
TC7WU04F
8
7
6
5
A
B
GND
VCC
Y
5
4
FLASH_CS-
SN74LVC1G32
FLASH_WPR21
10K
JP3
F91_WE-
1
2
F91WR_EN
Figure 7. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic Diagram: SRAM and Flash Memories
PS030603-1013
19
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
A[23:0]
D[7:0]
A[23:0]
D[7:0]
J1
TRSTNF91_WE-
TRSTNF91_WEA6
A10
A8
A13
A15
A18
A19
A2
A11
A4
A5
CS0CS2-
MREQWRBUSACK-
A21
A22
CS0CS2D1
D3
D5
D7
MREQGND
WRBUSACK-
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
J2
PA7
PA5
PA3
PA1
VCC_3v3
A0
A3
PB7
PB5
PB3
PB1
A7
A9
A14
A16
A1
A12
A20
A17
DIS_FLASHA23
CS1D0
D2
D4
PC6
PC4
PC2
PC0
PD6
PD5
PD3
PD1
TDO
DIS_FLASHCS1-
TCK
RTC_VDD
IICSCL
IICSDA
FLASH_WECS3RESET-
GND
D6
IOREQRDINSTRDBUSREQ-
IORQRDINSTRDBUSREQ-
HALT_SLP-
HDR/PIN 2x30
PA7
PA5
PA3
PA1
VCC_3V3
PB7
PB5
PB3
PB1
PC6
PC4
PC2
PC0
PD6
PD5
PD3
PD1
TD0
GND
TCK
RTC_VDD
IICSCL
IICSDA
FLASH_WECS3RESETHALT_SLP-
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
PA6
PA4
PA2
PA0
PB6
PB4
PB2
PB0
PC7
PC5
PC3
PC1
PD7
PD4
PD2
PD0
TDI
TRIGOUT
TMS
EZ80CLK
PA6
PA4
PA2
PA0
PB6
PB4
PB2
PB0
PC7
PC5
PC3
PC1
PD7
PD4
PD2
PD0
TDI
TRGOUT
TMS
EZ80CLK
GND
WAITNMI-
WAITNMI-
HDR/PIN 2x30
VCC_3v3
VCC_3v3
VCC_3v3
GND
Figure 8. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic Diagram: J1 and J2 Connectors
PS030603-1013
20
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
D[7:0]
VCC_3v3
R1
10K
R2
R3
10K
R4
10K
R5
10K
R7
R6
10K
L2
K3
J4
M3
L3
H5
L4
M4
10K
10K
L6
WAIT-
M7
BUSREQ-
J6
NMITMS
TCK
TDI
TRSTNRESETF91_WP-
H7
L9
K9
L10
ZCL
ZDA
SYS_RST-
K6
A2
R11
4.75K
C1
MII_CRS
MII_COL
MII_RXER
MII_RXDV
0.1uF
MII_RXD[3:0]
MII_RXD3
MII_RXD2
MII_RXD1
MII_RXD0
MII_RXCLK
MII_TXCLK
D8
A7
D6
A4
C4
D5
B4
E6
C5
C6
J10
R13
499
H11
Y1
C2
H12
220pF
50.000MHZ
C3
VCC_3v3
R16
H10
G7
200K
L1
0.056uF
C4
C5
5pF
10pF
3.3UH
C6
0.1uF
A5
B8
C1
C10
E2
E11
G2
H9
J2
J11
K4
K7
M1
D0
D1
D2
D3
D4
D5
D6
D7
WAIT
BUSREQ
NMI
TMS
TCK
TDI
TRSTN
RESET
WP
MII_CRS
MII_COL
MII_RXER
MII_RXDV
MII_RXD3
MII_RXD2
MII_RXD1
MII_RXD0
MII_RXCLK
MII_TXCLK
FILT_IN
XIN
XOUT
PLL_VDD
PLL_VSS
VDD1
VDD2
VDD3
VDD4
VDD5
VDD6
VDD7
VDD8
VDD9
VDD10
VDD11
VDD12
VDD13
VCC_3v3
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
R17
931
D1
2
RTC_VDD
1
RB751V
VCC_3v3
D2
VCC_3v3
1
2
J7
L8
M8
1
2
ML2020
BT1
GND
B5
B12
C2
C8
D9
E3
F9
G3
G6
G12
H4
H6
J12
K8
M2
M11
BATT+
RB751V
A[23:0]
U2
D0
D1
D2
D3
D4
D5
D6
D7
Y2
C20
18pF
32.768KHZ
VSS1
VSS2
VSS3
VSS4
VSS5
VSS6
VSS7
VSS8
VSS9
VSS10
VSS11
VSS12
VSS13
VSS14
VSS15
VSS16
RTC_VDD
RTC_XOUT
RTC_XIN
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
MII_TXD3
MII_TXD2
MII_TXD1
MII_TXD0
MII_TXEN
MII_TXER
MII_MDC
MII_MDIO
IORQ
MRQ
RD
WR
BUSACK
CS0
CS1
CS2
CS3
SCL
SDA
PA7_PWM3
PA6_PWM2_EC1
PA5_PWM1_TOUT1
PA4_PWM0_TOUT0
PA3_PWM3_OC3
PA2_PWM2_OC2
PA1_PWM1_OC1
PA0_PWM0_OC0
PB7_MOSI
PB6_MISO
PB5_ICB3
PB4_ICA2
PB3_SCK
PB2_SS
PB1_IC1
PB0_IC0_EC0
PC7_RI1
PC6_DCD1
PC5_DSR1
PC4_DTR1
PC3_CTS1
PC2_RTS1
PC1_RXD1
PC0_TXD1
PD7_RI0
PD6_DCD0
PD5_DSR0
PD4_DTR0
PD3_CTS0
PD2_RTS0
PD1_RXD0_IRRXD
PD0_TXD0_IRTXD
HALT_SLP
PHI
INSTRD
TDO
TRIGOUT
C21
18pF
A1
B1
B2
C3
D4
E5
D2
D1
D3
F6
E1
E4
F1
F2
F3
F4
G1
F5
H1
H2
G4
H3
J1
G5
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
B7
C7
D7
A6
B6
E7
A3
B3
VCC_3v3
R8
R9
0 ohm
PB2
0 ohm
PB6
1
2
3
4
CS
SO/IO1
WP/ACC/IO2
GND
VCC
HOLD/IO3
SCK
SI/IO0
8
7
6
5
PB3
PB7
S25FL032
MII_TXD[3:0]
MII_TXD3
MII_TXD2
MII_TXD1
MII_TXD0
R12
MII_TXEN
MII_TXER
MII_MDC
MII_MDIO
33.2
M5
L5
K5
J5
L7
J3
K1
K2
L1
IORQMREQRDWRBUSACKCS0CS1CS2CS3-
VCC_3v3
R14
4.99K
R15
4.99K
A11
A12
IICSCL
IICSDA
A8
F7
C9
A9
B9
E8
B10
A10
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
C11
C12
D10
E9
D11
F8
D12
E10
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
E12
G8
F10
F11
F12
G9
G10
G11
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
H8
K11
K12
J9
K10
L11
L12
M12
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
M9
B11
M6
M10
J8
U3
SSMISO
R10
10K
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
R18
33.2
Place resistor near CPU
HALT_SLPEZ80CLK
INSTRDTDO
TRGOUT
eZ80F91_BGA
Figure 9. eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet ModuleSchematic Diagram: MCU
PS030603-1013
21
eZ80Acclaim!™/eZ80AcclaimPlus!™ Ethernet Modules
Product Specification
Customer Support
To share comments, get your technical questions answered, or report issues you may be
experiencing with our products, please visit Zilog’s Technical Support page at
http://support.zilog.com.
To learn more about this product, find additional documentation, or to discover other facets about Zilog product offerings, please visit the Zilog Knowledge Base at http://
zilog.com/kb or consider participating in the Zilog Forum at http://zilog.com/forum.
This publication is subject to replacement by a later edition. To determine whether a later
edition exists, please visit the Zilog website at http://www.zilog.com.
PS030603-1013
22
工商网监
湘ICP备2023018690号
