Z0220100ZCO

PRELIMINARY CUSTOMER PROCUREMENT SPECIFICATION 1 Z0220100ZCO 1 MODEM EVALUATION KIT FEATURES ■ ■ Supported Devices Part Number Package Type Z02201 Z02205 44-Pin PLCC 28-Pin SOIC Z02201 Modem Evaluation Board Includes: – Supported Protocols: V.22bis, V.22, V.21, V.23, Bell 103, Bell 212A – AT Commands for Modem Control and Configuration – – – – Shipped with North America-style DAA Socket for DAA Module Allows User-Defined DAA Eye Pattern Port One RS-232C Serial Port with DB25 Connectors ■ User Manual for Demonstration Board ■ “Diplomat” PC-based Configuration Utility to Allow Configuration of Modem Controller Code for Worldwide Country Support ■ Object Code to be Modified by the Diplomat Configuration Utility GENERAL DESCRIPTION The Modem Evaluation Kit (Z0220100ZCO) is a generalpurpose platform that allows users to evaluate the capabilities and operation of the Z02201 Modem DSP and Analog Front End, and the Z02205 Modem controller. The kit contains an assembled circuit board, software, and documentation to support software and hardware development for low speed embedded modem applications. The demonstration board provides connections to the phone network (RJ11) and to a PC (RS232). Eye pattern output allows the display of the modem signal on an X-Y oscilloscope. LED indicators provide a visual display of various modem signals. A speaker provides an audible monitor of modem handshake and dialing tones. The Diplomat PC-based Configuration utility allows the user to configure modem controller code to meet the requirements in various countries. Look-up tables are provided that enable modification of dial modifiers and call progress parameters to accommodate the needs of various phone networks. SPECIFICATIONS Dimensions Approximately 5 inches by 7 inches Serial Interface RS-232C Power Requirements +12V AC ±5%, 1 A (typical) Environmental Operating Conditions Operating Temperature: +20°C ±10°C Relative Humidity: 10-90%, non-condensing CP97FMO0501 PRELIMINARY 1 Z0220100ZCO Modem Evaluation Kit Zilog KIT CONTENTS Hardware – Modem Evaluation Card including modem DSP code in on-chip ROM, and modem controller code in on-chip ROM – 12VAC power converter (110V wall supply). Connector is 2.1mm (inner diameter) by 5.5mm (outer diameter) female type – RJ11 Phone Cord (6 feet length) 3.5” High Density Floppy Disk – Utility Program for configuring modem controller code for use in different countries – Hex Object Code to be Modified – – Sample Datapump Driver Code Written in C read.me file includes instructions for using the eval kit Documentation – Evaluation Kit User Manual – Low Speed Embedded Modem Chipsets DataBook – Schematics of the demonstration board in OrCAD for Windows – “Print files” of board schematic – Net list of evaluation board – Registration Card ADDITIONAL REQUIRED AND OPTIONAL ITEMS Required Items Not Supplied with Kit – IBM PC (or compatible) with the following minimum1 recommended configuration: – – – – – – – 386 CPU, 33 MHz 4 MB of RAM Hard disk drive (1 MB free space)2 VGA video adapter 3.5-inch high-density floppy disk drive RS-232C communications port Windows® 3.1 or Windows 95 Notes: 1. For increased performance we recommend a 486- or Pentium-based machine operating at 66 MHz or faster with 8 MB of RAM. 2. Additional disk space may be required for terminal emulator program(s), C compiler, and user-generated source files. – – – 2 A terminal emulator program such as Windows Terminal, HyperTerm™ or ProComm™ running on the PC RS-232C cable to connect the card to the host PC 25-pin to 9-pin adaptor Optional Items Not Supplied with Kit – CP Clare DAA Modules CP Clare Corporation 78 Cherry Hill Drive Beverly, MA 01915-1048 TEL: 978-524-6700 FAX: 978-524-4700 1-800-CP-CLARE NET: www.cpclare.com – Z89C50 ICEBOX Z8 Emulator for modifications to modem controller code and to program Z02205 Modem Controller – Additional jumper wires and shunts – C-compiler for modem controller code -- Z8C Code Development System (available from Bytecraft Limited): Bytecraft Limited 421 King Street North Waterloo, Ontario, Canada N2J 4E4 TEL: 1-519-888-6911 FAX: 1-519-746-6751 NET: www.bytecraft.com PRELIMINARY CP97FMO0501 Z0220100ZCO Modem Evaluation Kit Zilog PRECAUTIONS AND LIMITATIONS There are no known anomalies with the Evaluation Card itself. However, there a small number of anomolies with the Z02201 device included on the board. The errata is listed below. The Z02201 chip on the card is mounted in a socket to allow replacement with newer versions of the device as they become available. For ease of replacement, Zilog recommends the use of the AMP extraction tool noted above. Development Projects: Customer is cautioned that while reasonable efforts will be employed to meet performance objectives and milestone dates, development t is subject to unanticipated problems Pre-Characterization Product: The product represented by this CPS is newly introduced and Zilog has not completed the full characterization of the product. The CPS states what Zilog knows about this product at this time, but additional features or nonconformance with some aspects of the CPS may be found, Low Margin: Customer is advised that this product does not meet Zilog's internal guardbanded test policies for the specification requested and is supplied on an exception basis. Customer is cautioned that delivery may be uncertain and that, in addition to all other limitations on © 1998 by Zilog, Inc. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Zilog, Inc. The information in this document is subject to change without notice. Devices sold by Zilog, Inc. are covered by warranty and patent indemnification provisions appearing in Zilog, Inc. Terms and Conditions of Sale only. ZILOG, INC. MAKES NO WARRANTY, EXPRESS, STATUTORY, IMPLIED OR BY DESCRIPTION, REGARDING THE INFORMATION SET FORTH HEREIN OR REGARDING THE FREEDOM OF THE DESCRIBED DEVICES FROM INTELLECTUAL PROPERTY INFRINGEMENT. ZILOG, INC. MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE. Known Anomalies With Z02201 R3470 There is only one currently known problem on the Z02201, ROM code R3470: 1. DPBUSY bit is not properly set during timed DTMF operation. As this is a new feature in the R3470 code set, it is not a problem for those users that are used to the feature set of previous ROM codes. A microcontroller workaround is available. and delays. No production release is authorized or committed until the Customer and Zilog have agreed upon a Customer Procurement Specification for this project. either by Zilog or its customers in the course of further application and characterization work. In addition, Zilog cautions that delivery may be uncertain at times, due to start-up yield issues. Zilog liability stated on the front and back of the acknowledgment, Zilog makes no claim as to quality and reliability under the CPS. The product remains subject to standard warranty for replacement due to defects in materials and workmanship. Zilog’s products are not authorized for use as critical components in life support devices or systems unless a specific written agreement pertaining to such intended use is executed between the customer and Zilog prior to use. Life support devices or systems are those which are intended for surgical implantation into the body, or which sustains life whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Zilog, Inc. 210 East Hacienda Ave. Campbell, CA 95008-6600 Telephone (408) 370-8000 FAX 408 370-8056 Internet: http://www.zilog.com Zilog, Inc. shall not be responsible for any errors that may appear in this document. Zilog, Inc. makes no commitment to update or keep current the information contained in this document. CP97FMO0501 PRELIMINARY 3 1