Z8E00110SSG

DATA SHEET Z8E001 1 FEATURE-RICH Z8PLUS ONE-TIME PROGRAMMABLE (OTP) MICROCONTROLLER FEATURES Part Number ROM (KB) RAM* (Bytes) Speed (MHz) 64 10 Z8E001 1 Note: * General-Purpose Microcontroller Core Features ¥ All Instructions Execute in one 1 µs Instruction Cycle with a 10 MHz Crystal ¥ ¥ ¥ ¥ ¥ 1K x 8 On-Chip OTP EPROM Memory ¥ ¥ ¥ ¥ 64 x 8 General-Purpose Registers (SRAM) Includes Special Functionality: Stop-Mode Recovery Input, Comparator Inputs, Selectable Edge Interrupts, and Timer Output One Analog Comparator 16-Bit Programmable Watch-Dog Timer (WDT) Software Programmable Timers Configurable as: Ð Two 8-Bit Standard Timers and One 16-Bit Standard Timer, or Ð One 16-Bit Standard Timer and One 16-Bit Pulse Width Modulator (PWM) Timer Six Vectored Interrupts with Fixed Priority Additional Features Operating Speed: DCÐ10 MHz ¥ On-Chip Oscillator that accepts an XTAL, Ceramic Resonator, LC, or External Clock ¥ Programmable Options: Ð EPROM Protect 13 Total Input/Output Pins ¥ One 8-Bit I/O Port (Port A) Ð I/O Bit Programmable Ð Each Bit Programmable as Push-Pull or OpenDrain Power Reduction Modes: Ð HALT Mode with Peripheral Units Active Ð STOP Mode with all Functionality Shut Down CMOS/Technology Features One 5-Bit I/O Port (Port B) Ð I/O Bit Programmable ¥ ¥ Six Addressing Modes: R, IR, X, D, RA, & IM Peripheral Features ¥ ¥ Ð ¥ Low-Power Consumption 3.5V to 5.5V Operating Range @ 0°C to +70°C 4.5V to 5.5V Operating Range @ Ð40°C to +105°C 18-Pin DIP, SOIC, and 20-Pin SSOP Packages. GENERAL DESCRIPTION Allowing easy software development, debug, and prototyping, ZiLOGÕs new Z8E001 Microcontroller (MCU) offers a cost-effective One-Time Programmable (OTP) solution to its single-chip Z8Plus MCU family. For applications demanding powerful I/O capabilities, the Z8E001Õs dedicated input and output lines are grouped into two ports, and are configurable under software control. Both 8-bit and 16-bit on-chip timers, with a large number of user-selectable modes, offload the system of administer- DS001101-Z8X0400 1 Z8E001 Z8Plus OTP Microcontroller ZiLOG GENERAL DESCRIPTION (Continued) ing real-time tasks such as counting/timing and I/O data communications. Power connections follow conventional descriptions below: Note: All signals with an overline, Ò Ó, are active Low. For example, B/ W (WORD is active Low, only); B /W (BYTE is active Low, only). VCC Connection Circuit Device Power VCC VDD Ground GND VSS GND Two 8-bit Timers or One 16-bit PWM Timer XTAL RESET Machine Timing ALU One 16-bit Std. Timer FLAG OTP Prg. Mem- Interrupt Control Register Pointer One Analog Comparator Program Counter RAM Register Port A Port B I/O I/O Figure 1. Functional Block Diagram 2 PRELIMINARY DS001101-Z8X0400 Z8E001 Z8Plus OTP Microcontroller ZiLOG D7Ð0 AD9Ð0 Z8E001 MCU AD9Ð0 ADDRESS MUX ADDRESS GENERATOR AD9Ð0 EPROM D7Ð0 DATA MUX Z8E001 D7Ð0 PORT ROM PROT OPTION BIT A PGM + TEST MODE LOGIC PGM ADCLR/VPP ADCLK XTAL1 Figure 2. EPROM Programming Mode Block Diagram DS001101-Z8X0400 PRELIMINARY 3 Z8E001 Z8Plus OTP Microcontroller ZiLOG PIN DESCRIPTION PGM GND GND GND ADCLR/VPP D7 D6 D5 D4 1 18 18-Pin DIP 9 10 ADCLK XTAL1 NC GND VDD D0 D1 D2 D3 Figure 3. 18-Pin DIP/SOIC Pin Identification/EPROM Programming Mode EPROM Programming Mode Pin # Symbol Function Direction 1 2Ð4 5 PGM GND ADCLR/VPP Prog Mode Ground Clear Clk./Prog Volt. Input 6-9 10Ð13 14 D7ÐD4 D3ÐD0 VDD Data 7,6,5,4 Data 3,2,1,0 Power Supply 15 16 17 18 GND NC XTAL1 ADCLK Ground No Connection 1MHz Clock Address Clock 4 PRELIMINARY Input Input/Output Input/Output Input Input DS001101-Z8X0400 Z8E001 Z8Plus OTP Microcontroller ZiLOG PB1 PB2 PB3 PB4 RST PA7 PA6 PA5 PA4 1 18 DIP 18-Pin 9 10 PBO XTAL1 XTAL2 VSS VCC PA0 PA1 PA2 PA3 Figure 4. 18-Pin DIP/SOIC Pin Identification Standard Mode Pin # Symbol Function Direction 1Ð4 5 6-9 10Ð13 14 PB1ÐPB4 RESET PA7ÐPA4 PA3ÐPA0 VCC Port B, Pins 1,2,3,4 Reset Port A, Pins 7,6,5,4 Port A, Pins 3,2,1,0 Power Supply Input/Output Input Input/Output Input/Output 15 VSS Ground 16 17 18 XTAL2 XTAL1 PB0 Crystal Osc. Clock Crystal Osc. Clock Port B, Pin 0 DS001101-Z8X0400 PRELIMINARY Output Input Input/Output 5 Z8E001 Z8Plus OTP Microcontroller ZiLOG PIN DESCRIPTION (Continued) PB1 PB2 PB3 PB4 RESET NC PA7 PA6 PA5 PA4 1 20 SSOP 20-Pin 10 11 PBO XTAL1 XTAL2 VSS VCC NC PA0 PA1 PA2 PA3 Figure 5. 20-Pin SSOP Pin Identification Standard Mode Pin # Symbol Function Direction 1Ð4 5 6 7Ð10 11Ð14 15 16 PB1ÐPB4 RESET NC PA7ÐPA4 PA3ÐPA0 NC VCC Port B, Pins 1,2,3,4 Reset No Connection Port A, Pins 7,6,5,4 Port A, Pins 3,2,1,0 No Connection Power Supply Input/Output Input 17 VSS Ground 18 19 20 XTAL2 XTAL1 PB0 Crystal Osc. Clock Crystal Osc. Clock Port B, Pin 0 6 PRELIMINARY Input/Output Input/Output Output Input Input/Output DS001101-Z8X0400 Z8E001 Z8Plus OTP Microcontroller ZiLOG PGM GND GND GND ADCLR/VPP NC D7 D6 D5 D4 1 20 SSOP 20-Pin 10 11 ADCLK XTAL1 NC GND VDD NC D0 D1 D2 D3 Figure 6. 20-Pin SSOP Pin Identification/EPROM Programming Mode EPROM Programming Mode Pin # Symbol Function Direction 1 2Ð4 5 PGM GND ADCLR/VPP Prog Mode Ground Clear Clk./Prog Volt. Input 6 7Ð10 11Ð14 15 16 NC D7ÐD4 D3ÐD0 NC VDD No Connection Data 7,6,5,4 Data 3,2,1,0 No Connection Power Supply 17 18 19 20 GND NC XTAL1 ADCLK Ground No Connection 1MHz Clock Address Clock DS001101-Z8X0400 PRELIMINARY Input Input/Output Input/Output Input Input 7 Z8E001 Z8Plus OTP Microcontroller ZiLOG ABSOLUTE MAXIMUM RATINGS Parameter Min Max Units Note Ambient Temperature under Bias Storage Temperature Voltage on any Pin with Respect to VSS Ð40 Ð65 Ð0.6 +105 +150 +7 C C V 1 Voltage on VDD Pin with Respect to VSS Ð0.3 +7 V Voltage on RESET Pin with Respect to VSS Ð0.6 VDD+1 V Total Power Dissipation Maximum Allowable Current out of VSS 880 80 mW mA Maximum Allowable Current into VDD 80 mA +600 +600 25 mA mA mA 25 40 40 40 40 mA mA mA mA mA Maximum Allowable Current into an Input Pin Maximum Allowable Current into an Open-Drain Pin Maximum Allowable Output Current Sunk by Any I/O Pin Ð600 Ð600 Maximum Allowable Output Current Sourced by Any I/O Pin Maximum Allowable Output Current Sunk by Port A Maximum Allowable Output Current Sourced by Port A Maximum Allowable Output Current Sunk by Port B Maximum Allowable Output Current Sourced by Port B 2 3 4 Notes: 1. Applies to all pins except the RESET pin and where otherwise noted. 2. There is no input protection diode from pin to VDD. 3. Excludes XTAL pins. 4. Device pin is not at an output Low state. Stresses greater than those listed under Absolute Maximum Ratings can cause permanent damage to the device. This rating is a stress rating only. Functional operation of the device at any condition above those indicated in the operational sections of these specifications is not implied. Exposure to absolute maximum rating conditions for an extended period can affect device reliability. Total power dissipation should 8 not exceed 880 mW for the package. Power dissipation is calculated as follows: Total Power Dissipation = VDD x [IDD Ð (sum of IOH)] + sum of [(VDD Ð VOH) x IOH] + sum of (V0L x I0L) PRELIMINARY DS001101-Z8X0400 Z8E001 Z8Plus OTP Microcontroller ZiLOG STANDARD TEST CONDITIONS The characteristics listed below apply for standard test conditions as noted. All voltages are referenced to Ground. Positive current flows into the referenced pin (Figure 7). From Output Under Test 150 pF Figure 7. Test Load Diagram CAPACITANCE TA = 25¡C, VCC = GND = 0V, f = 1.0 MHz, unmeasured pins returned to GND. Parameter Input capacitance Output capacitance I/O capacitance DS001101-Z8X0400 Min Max 0 0 0 12 pF 12 pF 12 pF PRELIMINARY 9 Z8E001 Z8Plus OTP Microcontroller ZiLOG DC ELECTRICAL CHARACTERISTICS Table 1. DC Electrical Characteristics pF TA = 0¡C to +70¡C Standard Temperatures Typical2 @ 25¡C Units Conditions Sym Parameter VCC1 VCH Clock Input High Voltage 3.5V 0.7VCC VCC+0.3 1.3 V 5.5V 0.7VCC VCC+0.3 2.5 V 3.5V VSSÐ0.3 0.2VCC 0.7 V 5.5V VSSÐ0.3 0.2VCC 1.5 V VCL Clock Input Low Voltage Min Max Driven by External Clock Generator Driven by External Clock Generator Driven by External Clock Generator Driven by External Clock Generator VIH Input High Voltage 3.5V 5.5V 0.7VCC 0.7VCC VCC+0.3 VCC+0.3 1.3 2.5 V V VIL Input Low Voltage 3.5V 5.5V VSSÐ0.3 VSSÐ0.3 0.2VCC 0.2VCC 0.7 1.5 V V VOH Output High Voltage 3.5V VCCÐ0.4 3.1 V IOH = Ð2.0 mA 5.5V VCCÐ0.4 4.8 V IOH = Ð2.0 mA VOL1 Output Low Voltage Notes 3.5V 0.6 0.2 V IOL = +4.0 mA 5.5V 0.4 0.1 V IOL = +4.0 mA 1.2 0.5 V IOL = +6 mA IOL = +12 mA VOL2 Output Low Voltage 3.5V 1.2 0.5 V VRH Reset Input High Voltage 3.5V 0.5VCC VCC 1.1 V 5.5V 0.5VCC VCC 2.2 V 3.5V VSSÐ0.3 0.2VCC 0.9 V 5.5V VSSÐ0.3 0.2VCC 1.4 V 3.5V 5.5V 3.5V Ð1.0 25.0 25.0 2.0 10.0 10.0 0.064 mV mV mA VIN = 0V, VCC 5.5V Ð1.0 2.0 0.064 mA VIN = 0V, VCC 3.5V Ð1.0 2.0 0.114 µA VIN = 0V, VCC 5.5V Ð1.0 2.0 0.114 µA VIN = 0V, VCC 3.5V VSSÐ0.3 VCCÐ1.0 V 3 5.5V VSSÐ0.3 VCCÐ1.0 V 3 3.5V 5.5V Ð10 Ð20 Ð60 Ð180 5.5V VRL Reset Input Low Voltage VOFFSET Comparator Input Offset Voltage IIL IOL VICR IIR 10 Input Leakage Output Leakage Comparator Input Common Mode Voltage Range Reset Input Current PRELIMINARY Ð30 Ð100 µA µA DS001101-Z8X0400 Z8E001 Z8Plus OTP Microcontroller ZiLOG Table 1. DC Electrical Characteristics (Continued) pF TA = 0¡C to +70¡C Standard Temperatures 1 Typical2 @ 25¡C Units Conditions Sym Parameter VCC ICC Supply Current ICC1 Standby Current 3.5V 5.5V 3.5V 2.5 6.0 2.0 2.0 3.5 1.0 mA mA mA @ 10 MHz @ 10 MHz HALT Mode VIN = 0V, VCC @ 10 MHz 4,5 4,5 4,5 5.5V 4.0 2.5 mA HALT Mode VIN = 0V, VCC @ 10 MHz 4,5 3.5V 500 150 nA STOP Mode VIN = 0V, VCC 6 ICC2 Standby Current Min Max Notes Notes: 1. The VCC voltage specification of 3.5V guarantees 3.5V and the VCC voltage specification of 5.5 V guarantees 5.0 V ±0.5 V. 2. Typical values are measured at VCC = 3.3V and VCC = 5.0V; VSS = 0V = GND. 3. For analog comparator input when analog comparator is enabled. 4. All outputs unloaded and all inputs are at VCC or VSS level. 5. CL1 = CL2 = 22 pF. 6. Same as note 4 except inputs at VCC. DS001101-Z8X0400 PRELIMINARY 11 Z8E001 Z8Plus OTP Microcontroller ZiLOG DC ELECTRICAL CHARACTERISTICS (Continued) Table 2. DC Electrical Characteristics TA = Ð40¡C to +105¡C Extended Temperatures Sym Parameter VCC VCH Clock Input High Voltage VCL VIH VIL VOH VOL1 VOL2 VRH Clock Input Low Voltage Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage Output Low Voltage Reset Input High Voltage VOFFSET Comparator Input Offset Voltage 1 Typical2 @ 25¡C Units Conditions Min Max Notes 4.5V 0.7 VCC VCC+0.3 2.5 V 5.5V 0.7 VCC VCC+0.3 2.5 V 4.5V VSSÐ0.3 0.2 VCC 1.5 V 5.5V VSSÐ0.3 0.2 VCC 1.5 V 4.5V 0.7 VCC VCC+0.3 2.5 V 5.5V 0.7 VCC VCC+0.3 2.5 V 4.5V VSSÐ0.3 0.2 VCC 1.5 V 5.5V VSSÐ0.3 0.2 VCC 1.5 V 4.5V VCCÐ0.4 4.8 V IOH = Ð2.0 mA 5.5V VCCÐ0.4 4.8 V IOH = Ð2.0 mA Driven by External Clock Generator Driven by External Clock Generator Driven by External Clock Generator Driven by External Clock Generator 4.5V 0.4 0.1 V IOL = +4.0 mA 5.5V 0.4 0.1 V IOL = +4.0 mA 4.5V 1.2 0.5 V IOL = +12 mA 5.5V 1.2 0.5 V IOL = +12 mA 4.5V 0.5VCC VCC 1.1 V 5.5V 0.5VCC VCC 2.2 V Ð1.0 25.0 25.0 2.0 10.0 10.0