ZMOTION® Lenses
Product Specification
PS028610-1114
Copyright ©2014 Zilog, Inc. All rights reserved.
www.zilog.com
ZMOTION® Lenses
Product Specification
ii
Warning:
DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A
critical component is any component in a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2014 Zilog, Inc All rights reserved. Information in this publication concerning the devices, applications,
or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES
NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE
INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED
IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED
HEREIN OR OTHERWISE. The information contained within this document has been verified according
to the general principles of electrical and mechanical engineering.
ZMOTION and Z8 Encore! XP are trademarks or registered trademarks of Zilog, Inc. (An IXYS
Company). All other product or service names are the property of their respective owners.
PS028610-1114
Disclaimer
ZMOTION® Lenses
Product Specification
iii
Revision History
Each instance in the revision history table reflects a change to this document from its previous revision. For more details, refer to the corresponding pages or appropriate links provided in the table below.
Date
PS028610-1114
Revision
Level
Description
Page
Nov
2014
10
Changed focus of spec to cover ZMOTION lenses only; see All
related ZMOTION Pyroelectric Sensors Product
Specification (PS0336).
Feb
2013
09
Moved NCL-11 lens specification to Table 1; added the CM 2, 7
0.77 GI V2 lens specification; alphanumerically reordered all
lenses.
May
2012
08
Added the NCL-11 and EWA 0.3 GI V2 lens specifications.
35, 17
Nov
2011
07
Added the NCL-3R and NCL-10S lens specifications.
21, 33
Mar
2011
06
Intrusion lens specifications added.
37
Jan
2011
05
Modifications to some lens/sensor descriptions in Table 1.
2
Jan
2011
04
Updated to include two new Nicera sensors.
18, 28
Nov
2010
03
Updated to new Zilog/IXYS logo and accepted Zilog style;
replaced all instances of ePIR with advanced passive
infrared.
All
Sep
2010
02
Replaced Zilog logos, ePIR with ZMOTION, and Zdots with All
Module; fixed formatting and pagination issues; removed
references to GP and General Purpose.
Oct
2010
01
Original issue
All
Revision History
ZMOTION® Lenses
Product Specification
iv
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ZMOTION Lens Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ZMOTION Detection and Control Lens Specifications . . . . . . . . . . . . . . . . . . . . . . . 5
ZAA09GIT1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ZCM077GIV2 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ZCM077GIV3 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ZCM077GIV5 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ZCWM05GIV1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ZEWA03GIV2 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ZNCL3B Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ZNCL10R Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ZNCL926 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ZNCL10IL Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ZNCL10S Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ZNCL11 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
ZMOTION Intrusion Detection Lens Specifications . . . . . . . . . . . . . . . . . . . . . . . .
ZLR12GI12V3 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ZVB12GIV1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ZWA12GI12V4 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
38
39
40
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
PS028610-1114
Table of Contents
ZMOTION® Lenses
Product Specification
v
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
PS028610-1114
The ZAA09GIT1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
The ZCM077GIV2 Lens Specification: Front View . . . . . . . . . . . . . . . . . . . 7
The ZCM077GIV2 Lens Specification: Floor Coverage, Side View . . . . . . 8
The ZCM077GIV3 Lens Specification, #1 of 2 . . . . . . . . . . . . . . . . . . . . . . 9
The ZCM077GIV3 Lens Specification, #2 of 2 . . . . . . . . . . . . . . . . . . . . . 10
The ZCM077GIV5 Lens Specification, #1 of 3 . . . . . . . . . . . . . . . . . . . . . 11
The ZCM077GIV5 Lens Specification, #2 of 3 . . . . . . . . . . . . . . . . . . . . . 12
The ZCM077GIV5 Lens Specification, #3 of 3 . . . . . . . . . . . . . . . . . . . . . 13
The ZCWM05GIV1 Lens Specification: Wall Mount . . . . . . . . . . . . . . . . 15
The ZCWM05GIV1 Lens Specification: Ceiling Mount, #1 of 2 . . . . . . . . 16
The ZCWM05GIV1 Lens Specification: Ceiling Mount, #2 of 2 . . . . . . . . 17
The ZEWA03GIV2 Lens Specification, Dimensions . . . . . . . . . . . . . . . . . 18
The ZNCL3B Lens Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
The ZNCL3B Lens Specification, X Axis . . . . . . . . . . . . . . . . . . . . . . . . . . 20
The ZNCL3B Lens Specification, Y Axis . . . . . . . . . . . . . . . . . . . . . . . . . . 21
The ZNCL10R Lens Specification, Dimensions . . . . . . . . . . . . . . . . . . . . . 22
The ZNCL10R Dual-Element Lens Specification, Tab Direction A . . . . . . 23
The ZNCL10R Dual-Element Lens Specification, Tab Direction B . . . . . . 24
The ZNCL10R Quad-Element Lens Specification, Tab Direction A,
X Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
The ZNCL926 Lens Specification, Dimensions . . . . . . . . . . . . . . . . . . . . . 26
The ZNCL926 Detection Area with Quad-Element PIR . . . . . . . . . . . . . . . 27
The ZNCL926 Detection Area with Dual-Element PIR . . . . . . . . . . . . . . . 28
The ZNCL10IL Lens Specification, Dimensions . . . . . . . . . . . . . . . . . . . . 29
The ZNCL10IL Lens Specification, Tab Direction A, X Axis . . . . . . . . . . 30
The ZNCL10IL Lens Specification, Tab Direction A, Y Axis . . . . . . . . . . 31
The ZNCL10IL Lens Specification, Tab Direction B, X Axis . . . . . . . . . . 32
The ZNCL10IL Lens Specification, Tab Direction B, Y Axis . . . . . . . . . . 33
The ZNCL10S Lens Specification, Dimensions . . . . . . . . . . . . . . . . . . . . . 34
The ZNCL10S Dual-Element Lens Specification, X/Y Axes . . . . . . . . . . . 35
The ZNCL11 Lens Specification, Dimensions . . . . . . . . . . . . . . . . . . . . . . 36
The ZNCL11 Detection Area, X/Y Axes . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ZLR12GI12V3 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
ZVB12GIV1 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ZWA12GI12V4 Lens Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
List of Figures
ZMOTION® Lenses
Product Specification
vi
List of Tables
Table 1.
Table 2.
PS028610-1114
ZMOTION Detection and Control Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ZMOTION Intrusion Detection Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
List of Tables
ZMOTION® Lenses
Product Specification
1
Overview
Zilog’s ZMOTION Detection and Control and Intrusion Detection product families provide integrated and flexible solutions for Passive Infrared (PIR)-based motion detection
applications. These product families are based on the ZMOTION MCU, a high-performance microcontroller featuring integrated PIR motion detection algorithms. Each family
includes a selection of lenses and PIR sensors to fit a wide range of application requirements. Each lens combination is optimized for its intended application by configuration
settings loaded into the ZMOTION MCU ensuring the best possible performance while
significantly reducing development risk and minimizing time to market. Zilog’s PIR
Motion Detection Technology provides a dramatic improvement in both sensitivity and
stability over traditional designs and is scalable to many market segments including Security/Intrusion Detection, Lighting Control, HVAC, Access Control, Vending, Display,
Proximity, Power Management, Occupancy Sensing and many others.
This document provides the zone patterns and mechanical dimensions for the Zilog-supported lenses included in the ZMOTION Family. Each supported lens combination is provided with an associated configuration file for the ZMOTION MCU. It is possible to use
other lenses not directly supported by Zilog by developing the appropriate configuration
settings based on one of the existing files.
There are two general groups of lenses provided:
•
•
ZMOTION Detection and Control for general motion detection applications
ZMOTION Intrusion Detection for security applications
These lens groupings are based on typical usage; any of these lenses could be used for a
variety of applications and are not limited to these suggested applications. All lenses listed
in this document are available from Zilog or from their associated manufacturers. Because
Zilog is regularly adding new lens support to these ZMOTION product families, please
obtain the latest version of this document from our website at: www.zilog.com/ZMOTION.
Note: To review the configuration files for specific lens and sensor combinations, refer to the
ZMOTION Detection Lens and Pyroelectric Sensor Configuration Guide (WP0018).
PS028610-1114
Overview
ZMOTION® Lenses
Product Specification
2
ZMOTION Lens Selection Guide
Select a lens and pyroelectric sensor based on the intended application from Table 1.
Lenses for security/intrusion-related applications are listed in Table 2. To see the specifications for lenses used in security and intrusion detection applications, refer to the ZMOTION Pyroelectric Sensors Specification (PS0336).
Table 1. ZMOTION Detection and Control Lenses
Part Number
Description
Recommended
Applications
Recommended
Pyroelectric
Sensor(s)
Manufacturer
and MFR Part
Number
Animal Alley Array (88°) Corner wall mount or very ZRE200BP
ZAA09GIT1
Lens
• 35.6mm x 49.9mm Flat high ceiling with
ZSBG446671
Specification –
rectangular floor pattern
Fresnel lens
see page 6
• 22.9mm focal length
• Warehouse Lighting
• 25 meter range
(Bay Light)
• 22 equal segments
• Combined Intrusion
and Lighting Control
• HVAC
Fresnel
Technologies
Inc.
Low height ceiling mount
ZCM077GIV2 Ceiling Mount Array
(360°)
Lens
for commercial lighting
Specification – • 37mm diameter circular control
see page 7
• Commercial HVAC
lens
• 19.6 mm focal length
• 12.2 m radius at 3.7 m
height
• 4:1 floor coverage
diameter-to-height ratio
ZSBG446671
Fresnel
Technologies
Inc.
Ceiling Mount for
ZCM077GIV3 Ceiling Mount Array
(360°)
Lens
standard commercial
Specification – • 37mm diameter circular heights
see page 9
• Lighting Control
lens
• 19.6mm focal length
• HVAC Control
• 3.7m radius at 2.4m
• Meeting rooms
height
• 3:1 floor coverage
diameter to height ratio
ZSBG446671
PS028610-1114
AA 0.9 GI T1
CM 0.77 GI V2
Fresnel
Technologies
Inc.
CM 0.77 GI V3
ZMOTION Lens Selection Guide
ZMOTION® Lenses
Product Specification
3
Table 1. ZMOTION Detection and Control Lenses (Continued)
Part Number
Description
Recommended
Applications
Recommended
Pyroelectric
Sensor(s)
Manufacturer
and MFR Part
Number
ZCM077GIV5 Ceiling Mount Array
High ceiling mount for
ZSBG446671
(360°)
Lens
commercial and industrial
Specification – • 37mm diameter circular applications
see page 11
• Commercial Lighting
lens
• 19.6mm focal length
Control
• 12.2m radius at 12.2m • Commercial HVAC
height
Control
• 2:1 floor coverage
diameter to height ratio
Fresnel
Technologies
Inc.
ZCWM05GIV1 Ceiling Mount Array (360° Wall or ceiling mount for
oval pattern)
Lens
office or meeting room
Specification – • Wall mount array
• Room Lighting and
see page 14
(~100°, ~8m coverage)
HVAC Control
• Circular lens with
24mm x 24mm square
base
• 14.2mm focal length
• Board mount clip-in
ZRE200BP
Fresnel
Technologies
Inc.
ZEWA03GIV2 Extra Wide Angle Wall
Mount Array (180°)
Lens
Specification – • 14mm x 28mm
see page 17
• 7.6mm focal length
• 5 meter range
• 16 equal segments
ZRE200BP
Room occupancy and
proximity sensing
ZSBG323671
CM 0.77 GI V5
CWM 0.5 GI
V1
ZSBG323671
180° detection with a
single pyro
• Wall mount room
lighting control
• AC light switch
replacement
• Hotel room thermostats
Fresnel
Technologies
Inc.
EWA 0.3 GI V2
Proximity or Entrance
ZRE200BP
ZNCL3B Lens 10mm wall mount array
Detection
Specification – (60° x 60°)
ZSBG323671
see page 18
•
Kiosk
• Clips on to pyroelectric
• Vending
sensor
• 2 beams (X); 2 beams • HVAC
• Display counters
(Y)
• Under-cabinet Lighting
• 10m range
Nippon
Ceramic Co.,
Ltd. (Nicera)
10mm Ceiling Mount
Proximity or Entrance
ZNCL10R
Lens
Detection
• Array (90° x 77°)
Specification – • Clips on to pyroelectric • HVAC
see page 21
• Display counters
sensor
• Lighting Controls
Nippon
Ceramic Co.,
Ltd. (Nicera)
PS028610-1114
ZSBG446671
ZRE200BP
ZSBG323671
NCL-3B
NCL-10R
ZMOTION Lens Selection Guide
ZMOTION® Lenses
Product Specification
4
Table 1. ZMOTION Detection and Control Lenses (Continued)
Recommended
Pyroelectric
Sensor(s)
Manufacturer
and MFR Part
Number
ZNCL926 Lens Clip-on 15mm Array
Room Occupancy and
Specification – (360°)
Proximity Sensing
see page 25
• Clips on to pyroelectric • Lighting Control
• HVAC Control
sensor
• 2.5m radius at 2.5m
• Appliance
• Kiosk/Display Control
height
• 2:1 Floor coverage
• Vending Power
diameter to height ratio
Management
• Appliance
• Power Management
ZRE200BP
Nippon
Ceramic Co.,
Ltd. (Nicera)
10mm Wall/Ceiling Mount Proximity or Entrance
ZNCL10IL
Array (80° x 30°)
Lens
Detection
Specification – • Clips on to pyroelectric • Kiosk
see page 28
• Vending
sensor
• 6 beams (X); 2 beams • HVAC
• Display counters
(Y)
• 10m range
ZRE200BP
10mm wall mount (27°)
ZNCL10S
directional
Lens
Specification – • Clips on to pyroelectric
see page 33
sensor
• 2 beams (X), 1 beam
(Y)
• 10m range
Entrance detection
ZRE200BP
Kiosk
ZSBG323671
ZNCL11 Lens Wall mount array 104°
Specification – (X), 37° (Y)
see page 35
• 32 detection zones
• Circuit board mount,
black rectangular lens
• 4m range
Room occupancy and
proximity sensing
• Consumer electronics
and appliance power
management
• Display power
management
• TV auto shutoff
• Keypad motion
detector
Part Number
PS028610-1114
Description
Recommended
Applications
ZSBG323671
ZSBG446671
ZSBG323671
NCL-9(26)
Nippon
Ceramic Co.,
Ltd. (Nicera)
NCL-10IL
Vending
Nippon
Ceramic Co.,
Ltd. (Nicera)
NCL-10S
HVAC
Display counters
Directional Detection
ZRE200BP
ZSBG323671
Nippon
Ceramic Co.,
Ltd. (Nicera)
NCL-11
ZMOTION Lens Selection Guide
ZMOTION® Lenses
Product Specification
5
Table 2. ZMOTION Intrusion Detection Lenses
Part Number
Description
ZLR12GI12V3 Long Range Array
Lens
42.6 mm x 61.0 mm Flat
Specification – Fresnel
see page 38
30.5 mm (1.2ʺ) focal
length
Typical Applications
Wall-mount long range
corridor/hallway security/
intrusion motion detector
Configuration
Header File
Pyroelectric
Sensor
ZRE200BP
Fresnel
Technologies
Inc.
ZSBG446671
LR 1.2 GI 12
V3
30.5m (100') range
3:1 floor coverage
diameter to height ratio
Vertical Barrier Array
ZVB12GIV1
Lens
42.6 mm x 61.0 mm Flat
Specification – Fresnel
see page 39
30.5 mm (1.2ʺ) focal
length
Wall- or ceiling-mount
curtain or vertical barrier
security/intrusion motion
detector
ZRE200BP
Corner/Wall Mount
security/intrusion motion
detector
• Pet immunity detector
• Wide-area security
motion detector
ZRE200BP
ZSBG446671
Fresnel
Technologies
Inc.
VB 1.2 GI V1
15 meter range, horizontal
7m range, vertical
ZWA12GI12V4 Wide Angle Array (88°)
Lens
42.6 mm x 61.0 mm Flat
Specification – Fresnel
see page 40
30.5 mm (1.2ʺ) focal
length
18 meter range
ZSBG446671
Fresnel
Technologies
Inc.
WA 1.2 GI 12
V4
ZMOTION Detection and Control Lens Specifications
Figures 1 through 27 on the following pages discuss the specifications of the lenses
selected for the ZMOTION Detection and Control family of products. To see specifications for lenses used in security and intrusion detection applications, refer to the ZMOTION Intrusion Detection Lens Specifications section on page 37.
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
6
ZAA09GIT1 Lens Specification
The ZAA09GIT1 lens array is optimized for dual-element pyroelectric sensors in long
range sensing applications. It is normally used with the grooved side facing the pyroelectric detector, and curved at a 0.9 inch (22.9 mm) radius about the sensitive area of the
detector. The detector position should be 0.492" (12.5 mm) below the upper edge, and centered left-right.
FRONT VIEW:
49.9mm
(1.965in)
TOP VIEW:
12.5mm
(.492in)
35.6mm
(1.400in)
15 m
(45ft)
0
88°
15 m
(45ft)
SIDE VIEW:
2.1m
(6.8ft)
15m
(45ft)
Figure 1. The ZAA09GIT1 Lens Specification
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
7
ZCM077GIV2 Lens Specification
The ZCM077GIV2 lens is intended for high ceiling-mounted commercial lighting and HVAC
applications in which high floor coverage is required. See Figures 2 and 3.
Detector Position
11.7mm
(0.46in)
Grooved Side
Notch Radius 1.5mm (0.060in)
19.6mm
(0.77in)
15°
Inactive Area
TOP VIEW:
9.1m
(30ft)
CL
52.5mm
(2.066in)
6.1m
(20ft)
7.8mm
(0.3in)
CL
3.0m
(10ft)
CL
0
3.0m
(10ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
6.1m
(20ft)
9.1m
(30ft)
SIDE VIEW:
0
8ft
(2.4m)
7.3m
(24ft)
4.3m
(14ft)
2.4m
(8ft)
0.9m 0 0.9m
(3ft)
(3ft)
2.4m
(8ft)
4.3m
(14ft)
7.3m
(24ft)
Figure 2. The ZCM077GIV2 Lens Specification: Front View
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
8
9.1m
(30ft)
CL
6.1m
(20ft)
3.0m
(10ft)
CL
0
3.0m
(10ft)
6.1m
(20ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
9.1m
(30ft)
(For mounting height of 2.4m (8ft))
SIDE VIEW:
0
8ft
(2.4m)
10ft
(3.0m)
12ft
(3.7m)
12.2m
(40ft)
9.1m
(30ft)
6.1m
(20ft)
3.0m
(10ft)
0
3.0m
(10ft)
6.1m
(20ft)
9.1m
(30ft)
12.2m
(40ft)
Figure 3. The ZCM077GIV2 Lens Specification: Floor Coverage, Side View
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
9
ZCM077GIV3 Lens Specification
The ZCM077GIV3 lens array is intended for ceiling-mounted applications and is optimized for use with both dual and quad element pyroelectric sensors. The detector mounting flange should be 0.46" (11.7 mm) from the pyroelectric sensor’s element. The angle
from the center line to the placement notch is 15 degrees.
FRONT VIEW :
Detector Position
11.7mm
(0.46in)
Grooved Side
19.6mm
(0.77in)
Notch Radius 1.5mm (0.060in)
TOP VIEW:
4.6m
(15ft)
CL
52.5mm
(2.066in)
3.0m
(10ft)
7.8mm
(0.3in)
1.5m
(5ft)
CL
CL
0
1.5m
(5ft)
3.0m
(10ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
4.6m
(15ft)
SIDE VIEW:
0
8ft
(2.4m)
3.7m
(12ft)
2.7m 2.1m 1.5m 0.9m
(9ft) (7ft) (5ft) (3ft)
0
0.9m 1.5m 2.1m 2.7m
(3ft) (5ft) (7ft) (9ft)
3.7m
(12ft)
Figure 4. The ZCM077GIV3 Lens Specification, #1 of 2
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
10
FLOOR
COVERAGE:
(For mounting height of 2.4m (8ft))
4.6m
(15ft)
CL
3.0m
(10ft)
1.5m
(5ft)
CL
0
1.5m
(5ft)
3.0m
(10ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
4.6m
(15ft)
SIDE VIEW:
0
8ft
(2.4m)
10ft
(3.0m)
12ft
(3.7m)
6.1m
(20ft)
4.6m
(15ft)
3.0m
(10ft)
1.5m
(5ft)
0
1.5m
(5ft)
3.0m
(10ft)
4.6m
(15ft)
6.1m
(20ft)
Figure 5. The ZCM077GIV3 Lens Specification, #2 of 2
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
11
ZCM077GIV5 Lens Specification
The ZCM077GIV5 lens array is intended for ceiling-mounted applications and is optimized for both dual and quad element pyroelectric detectors. The detector mounting
flange should be 0.46" (11.7 mm) from the pyroelectric sensor’s element.
FRONT VIEW :
Detector Position
11.68mm
(0.46in) 19.56mm
(0.77in)
Grooved Side
TOP VIEW:
15°
Notch Radius 1.52mm (0.060in)
4.6m
(15ft)
CL
52.5mm
(2.066in)
3.0m
(10ft)
7.82mm
(0.308in)
1.5m
(5ft)
CL
CL
0
1.5m
(5ft)
3.0m
(10ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
4.6m
(15ft)
SIDE VIEW:
0
8ft
3.7m
(12ft)
2.7m 2.1m 1.5m 0.9m
(9ft) (7ft) (5ft) (3ft)
0
0.9m 1.5m 2.1m 2.7m
(3ft) (5ft) (7ft) (9ft)
3.7m
(12ft)
Figure 6. The ZCM077GIV5 Lens Specification, #1 of 3
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
12
FLOOR
COVERAGE:
12.2m
(40ft)
(For mounting height of 12.2m (30ft))
CL
(30ft)
9.1m
6.1m
(20ft)
(10ft)
3.0m
CL
0
3.0m
(10ft)
(20ft)
6.1m
9.1m
(30ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
(40ft)
12.2m
SIDE VIEW:
0
(20ft)
6.1m
9.1m
(30ft)
(40ft)
12.2m
12.2m
(40ft)
9.1m
(30ft)
6.1m
(20ft)
3.0m
(10ft)
0
3.0m
(10ft)
6.1m
(20ft)
9.1m
(30ft)
12.2m
(40ft)
Figure 7. The ZCM077GIV5 Lens Specification, #2 of 3
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
13
FLOOR
COVERAGE:
12.2m
(40ft)
(For mounting height of 12.2m (30ft),
and when a 4 element is used )
CL
(30ft)
9.1m
6.1m
(20ft)
(10ft)
3.0m
CL
0
3.0m
(10ft)
(20ft)
6.1m
9.1m
(30ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
(40ft)
12.2m
SIDE VIEW:
0
(20ft)
6.1m
9.1m
(30ft)
(40ft)
12.2m
12.2m
(40ft)
9.1m
(30ft)
6.1m
(20ft)
3.0m
(10ft)
0
3.0m
(10ft)
6.1m
(20ft)
9.1m
(30ft)
12.2m
(40ft)
Figure 8. The ZCM077GIV5 Lens Specification, #3 of 3
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
14
ZCWM05GIV1 Lens Specification
The CWM 0.5 GI V1 lens array is intended for both wall and ceiling-mounted applications
and is optimized for both dual and quad element pyroelectric detectors. The lens is
intended to clip directly into the circuit board over top of the pyroelectric sensor.
FRONT VIEW:
TOP VIEW:
1mm R
(0.04in)
9.1m
(30ft)
24mm
(0.94in)
2mm R
(0.08in)
24mm
(0.94in)
4.6m
(15ft)
TOP VIEW:
180°
0m
5.2mm
(0.2in)
14.2mm
(0.56in)
12mm
(0.47in)
CLIP DETAILS:
(Scale 10:1)
4.6m
(15ft)
2.5mm
(0.1in)
1.7mm
(0.065in)
9.1m
(30ft)
1.5
(0. mm
06
in)
SIDE VIEW:
1
(0. mm
04
in)
mm )
3.2 125in
(0.
1.2m
(4ft)
0m
2.4m
(8ft)
4.3m
(14ft)
9.1m
(30ft)
Figure 9. The ZCWM05GIV1 Lens Specification: Wall Mount
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
15
FRONT VIEW :
5.2mm
(0.2in)
14.2mm
(0.56in)
12mm
(0.47in)
TOP VIEW:
4.6m
(15ft)
1mm R
(0.04in)
CL
24mm
(0.94in)
3.0m
(10ft)
2mm R
(0.08in)
24mm
(0.94in)
1.5m
(5ft)
CL
0
CLIP DETAILS:
1.5m
(5ft)
(Scale 10:1)
2.5mm
(0.1in)
3.0m
(10ft)
1.7mm
(0.065in)
1.5
(0. mm
06
in)
4.6m
(15ft)
1
(0. mm
04
in)
SIDE VIEW:
0
mm )
3.2 125in
(0.
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
8ft
3.7m
(12ft)
2.7m 2.1m 1.5m 0.9m
(9ft) (7ft) (5ft) (3ft)
0
0.9m 1.5m 2.1m 2.7m
(3ft) (5ft) (7ft) (9ft)
3.7m
(12ft)
Figure 10. The ZCWM05GIV1 Lens Specification: Ceiling Mount, #1 of 2
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
16
FLOOR
COVERAGE:
(For mounting height of 7.62m (25ft))
9.1m
(30ft)
CL
6.1m
(20ft)
3.0m
(10ft)
CL
0
3.0m
(10ft)
6.1m
(20ft)
9.1m
(30ft)
Note: The "beam" pattern
obtained depends strongly
on the detector used with
this array. The pattern
shown is intended solely
as a general guide.
SIDE VIEW:
0
(15ft)
4.6 m
(25ft)
7.6 m
9.1m
(30ft)
6.1m
(20ft)
3.0m
(10ft)
0
3.0m
(10ft)
6.1m
(20ft)
9.1m
(30ft)
Figure 11. The ZCWM05GIV1 Lens Specification: Ceiling Mount, #2 of 2
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
17
ZEWA03GIV2 Lens Specification
The ZEWA03GIV2 lens is intended for wall-mounted room occupancy and proximity sensing applications in which an extra-wide sensing angle is required. See Figure 12.
Sensitive
Element
1.0"
(25.4mm)
.30"
(7.6mm)
4.6 m
28.4mm
(1.12in)
22.4mm
(0.88in)
13.8mm 7.6mm
(0.54in) (0.3in)
0.07"
0.08"
0.09"
0.2"
TOP VIEW:
ACTUAL SIZE
4.6 m
SIDE VIEW:
4.6m
Figure 12. The ZEWA03GIV2 Lens Specification, Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
18
ZNCL3B Lens Specification
The ZNCL3B lens is intended for wall-mounted entrance and proximity-sensing applications.
Figure 13. The ZNCL3B Lens Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
19
Figure 14. The ZNCL3B Lens Specification, X Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
20
Figure 15. The ZNCL3B Lens Specification, Y Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
21
ZNCL10R Lens Specification
The ZNCL10R lens is intended for ceiling-mounted entrance and proximity-sensing applications. This lens features two orientations, Tab A and Tab B, that can be used with the
pyroelectric sensor to provide different beam patterns. Figures 16 through 19.
' ,0 (1 6, 21
8 1,7
*$7(
/(16 ȭ
7H[WXUHG SDUW
DURXQG WKH FLUFOH
$
$
ȭ
ȭ
࠙723 9,(:ࠚ
>P P@
5
*DWH SDUW
UHVLGXDO RI FXWWLQJ 0D[
5
㺽
ȭ
ȭ
ȭ
࠙%27720 9,(:ࠚ
࠙$$
ࠚ
$
$
5
72 /( 5$ 1& ( :, 7+ 28 7 ,1 67 58 &7 ,2 1㸸
Figure 16. The ZNCL10R Lens Specification, Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
22
) ,( /' 2 ) 9, (:
' 8$ / 7< 3( (/(0(17 6,=( ; < *DSPP
7$ % GL UH FW LRQ $
P
㺽
$
;
P
;
P
P
P
<
;
<
%
㺽
㺽
㺽
㺽
<
P
<
P
㺽
P
㺽
;
P
㺽
P
P
P
P
P
=2 1( 6 ' 8$ / (/ (0(17
$5($6
81,7
>P @
Figure 17. The ZNCL10R Dual-Element Lens Specification, Tab Direction A
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
23
) ,( /' 2 ) 9, (:
' 8$ / 7< 3( (/(0(17 6,=( ; < *DSPP
7$ % GL UH FW LRQ %
P
㺽
%
P
;
P
$
;
P
P
<
;
<
㺽
㺽
<
P
<
P
㺽
㺽
㺽
P
P
㺽
;
㺽
P
P
P
P
P
=2 1( 6 ' 8$ / (/ (0(17
$5($6
81,7
>P @
Figure 18. The ZNCL10R Dual-Element Lens Specification, Tab Direction B
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
24
Figure 19. The ZNCL10R Quad-Element Lens Specification, Tab Direction A, X Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
25
ZNCL926 Lens Specification
The ZNCL926 lens is intended for ceiling-mounted and other general purpose motion
sensing applications. It is optimized for both dual and quad element pyroelectric sensors.
Tolerance : (+/-) 0.2
Unit [ mm ]
Figure 20. The ZNCL926 Lens Specification, Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
26
Sensor: Pyroelectric Infrared Sensor, 4 Element Type (one output)
Element Size: 1.0mm (X) x 1.0mm (Y) x Gap 1.0mm
Unit [ m ]
Figure 21. The ZNCL926 Detection Area with Quad-Element PIR
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
27
Sensor: Pyroelectric Infrared Sensor, Dual-Element Type
Element Size: 2.0mm (X) x 1.0mm (Y) x Gap 1.0mm
Unit [ m ]
Figure 22. The ZNCL926 Detection Area with Dual-Element PIR
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
28
ZNCL10IL Lens Specification
The ZNCL10IL lens is intended for wall-mounted entrance and proximity-sensing applications. This lens features two orientations, Tab A and Tab B, that can be used with the
pyroelectric sensor to provide different beam patterns. Refer to Figures 24 and 25 for the
Tab A beam patterns and to Figures 26 and 27 for the Tab B beam patterns.
Figure 23. The ZNCL10IL Lens Specification, Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
29
Figure 24. The ZNCL10IL Lens Specification, Tab Direction A, X Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
30
Figure 25. The ZNCL10IL Lens Specification, Tab Direction A, Y Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
31
Figure 26. The ZNCL10IL Lens Specification, Tab Direction B, X Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
32
Figure 27. The ZNCL10IL Lens Specification, Tab Direction B, Y Axis
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
33
ZNCL10S Lens Specification
The ZNCL10S lens is intended for wall-mounted entrance detection applications wherein
directional recognition is required. See Figures 28 and 29.
Figure 28. The ZNCL10S Lens Specification, Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
34
Figure 29. The ZNCL10S Dual-Element Lens Specification, X/Y Axes
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
35
ZNCL11 Lens Specification
The ZNCL11 lens is intended for wall-mounted room occupancy and proximity sensing
applications with 32 detection zones. See Figures 30 and 31.
Figure 30. The ZNCL11 Lens Specification, Dimensions
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
36
Figure 31. The ZNCL11 Detection Area, X/Y Axes
PS028610-1114
ZMOTION Detection and Control Lens Specifications
ZMOTION® Lenses
Product Specification
37
ZMOTION Intrusion Detection Lens Specifications
Figures 32 through 34 provide the zone patterns and mechanical dimensions for the ZMOTION Intrusion Detection family of products. Recommended placement of the pyroelectric
sensor is provided with the detector and lens inclined downward at an angle of 12 degrees.
If you wish to use a tilt angle other than 12 degrees while maintaining the specified zone
patterns, move the pyroelectric sensor up by 0.021" (0.53 mm) for each degree less than 12
degrees, or down by the same amount for each degree greater than 12 degrees.
The ZLR12GI12V3, ZVB12GIV1, and ZWA12GI12V4 lenses can be interchanged in the
same end product without modifications to the placement or angle of the lens.
These lenses may also be used in nonintrusion applications. For additional lenses that do
not require security/intrusion detection capabilities, refer to the ZMOTION Detection and
Control Lens Specifications section on page 5.
PS028610-1114
ZMOTION Intrusion Detection Lens Specifications
ZMOTION® Lenses
Product Specification
38
ZLR12GI12V3 Lens Specification
The ZLR12GI12V3 lens array is optimized for dual-element pyroelectric sensors in longrange corridor security applications. It is normally used with the grooved side facing the
pyroelectric detector, and curved at a 1.2 inch (30.5 mm) radius about the sensitive area of
the detector. The detector and the lens array should be inclined downward at an angle of
12 degrees. If you wish to use a tilt angle other than 12 degrees while maintaining the
specified zone pattern, move the pyroelectric sensor up by 0.021" (0.53 mm) for each
degree less than 12 degrees, or down by the same amount for each degree greater than 12
degrees. The detector position should be 0.812" (20.6 mm) below the upper edge, and centered left-to-right.
FRONT VIEW:
20.6mm
(0.81in)
42.6mm
(1.675in)
61mm
(2.4in)
TOP VIEW:
77°
5m
(16ft)
21.5°
2.5m
(8ft)
14°
29°
6.5°
CL
0
2.5m
(8ft)
5.0m
(16ft)
SIDE VIEW:
2.1m
(6.8ft)
1m
(3ft)
2.2m
(7ft)
3m
(10ft)
10.7m
(35ft)
30.5m
(100ft)
18.3m
(60ft)
Figure 32. ZLR12GI12V3 Lens Specification
PS028610-1114
ZMOTION Intrusion Detection Lens Specifications
ZMOTION® Lenses
Product Specification
39
ZVB12GIV1 Lens Specification
The ZVB12GIV1 lens array is optimized for dual-element pyroelectric sensors in vertical
barrier or curtain-type security applications. It is normally used with the grooved side facing the pyroelectric detector, and curved at a 1.2 inch (30.5 mm) radius about the sensitive
area of the detector. The detector and the lens array should be inclined downward at an
angle of 12 degrees. If you wish to use a tilt angle other than 12 degrees while maintaining
the specified zone pattern, move the pyroelectric sensor up by 0.021" (0.53mm) for each
degree less than 12 degrees, or down by the same amount for each degree greater than 12
degrees. The detector position should be 0.812" (20.6 mm) below the upper edge, and centered left-to-right.
Figure 33. ZVB12GIV1 Lens Specification
PS028610-1114
ZMOTION Intrusion Detection Lens Specifications
ZMOTION® Lenses
Product Specification
40
ZWA12GI12V4 Lens Specification
The ZWA12GI12V4 lens array is optimized for dual-element pyroelectric sensors in largearea security applications. It is normally used with the grooved side facing the pyroelectric
detector, and curved at a 1.2 inch (30.5 mm) radius about the sensitive area of the detector.
The detector and the lens array should be inclined downward at an angle of 12 degrees. If
you wish to use a tilt angle other than 12 degrees while maintaining the specified zone pattern, move the pyroelectric sensor up by 0.021" (0.53 mm) for each degree less than 12
degrees, or down by the same amount for each degree greater than 12 degrees. The detector position should be 0.812" (20.6 mm) below the upper edge, and centered left-to-right.
FRONT VIEW:
20.6mm
(0.81in)
42.6mm
(1.675in)
TOP VIEW:
61mm
(2.4in)
10m
(33ft)
5m
(16ft)
0
88.2°
5m
(16ft)
10m
(33ft)
SIDE VIEW:
2.1m
(6.8ft)
1.7m 3.7m
(6ft) (12ft)
7m
(23ft)
15.6m
(51ft)
18m
(60ft)
Figure 34. ZWA12GI12V4 Lens Specification
PS028610-1114
ZMOTION Intrusion Detection Lens Specifications
ZMOTION® Lenses
Product Specification
41
Related Documents
Additional information about the ZMOTION Families of Motion Detection MCUs can be
found in the following documents, which are available from the Zilog website.
Document
Number
Description
PB0225
ZMOTION Detection and Control Family Product Brief
PB0230
ZMOTION Intrusion Detection Product Brief
PS0228
Z8 Encore! XP® F082A Series Product Specification
PS0285
ZMOTION Detection and Control Family Product Specification
PS0288
ZMOTION Intrusion Detection Product Specification
PS0336
ZMOTION Pyroelectric Sensors Specification
AN0307
ZMOTION Detection Module Application Walkthrough
AN0309
ZMOTION High Brightness White LED Lighting Application Note
WP0017
A New PIR Motion Detection Architecture White Paper
WP0018
ZMOTION Detection Lens and Pyro Sensor Configuration Guide
Other ZMOTION Family Products
PS028610-1114
PB0244
ZMOTION Detection Module II Product Brief
PS0305
ZMOTION Detection Module II Product Specification
Related Documents
ZMOTION® Lenses
Product Specification
42
Customer Support
To share comments, get your technical questions answered, or report issues you may be
experiencing with our products, please visit Zilog’s Technical Support page at
http://support.zilog.com.
To learn more about this product, find additional documentation, or to discover other facets about Zilog product offerings, please visit the Zilog Knowledge Base at http://
zilog.com/kb or consider participating in the Zilog Forum at http://zilog.com/forum.
This publication is subject to replacement by a later edition. To determine whether a later
edition exists, please visit the Zilog website at http://www.zilog.com.
PS028610-1114
Customer Support