0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
U62H256AS2A55LL

U62H256AS2A55LL

  • 厂商:

    ZMD

  • 封装:

  • 描述:

    U62H256AS2A55LL - AUTOMOTIVE FAST 32K X 8 SRAM - Zentrum Mikroelektronik Dresden AG

  • 数据手册
  • 价格&库存
U62H256AS2A55LL 数据手册
U62H256A Automotive Fast 32K x 8 SRAM Features ! 32768 x 8 bit static CMOS RAM ! 35 and 55 ns Access Time ! Common data inputs and ! ! Description go High-Z until the new information is available. The data outputs have no preferred state. The Read cycle is finished by the falling edge of W, or by the rising edge of E, respectively. Data retention is guaranteed down to 2 V. With the exception of E, all inputs consist of NOR gates, so that no pull-up/pull-down resistors are required. ! ! ! ! ! ! ! ! The U62H256A is a static RAM manufactured using a CMOS process technology with the following operating modes: data outputs - Read - Standby Three-state outputs - Write - Data Retention Typ. operating supply current The memory array is based on a 35 ns: 45 mA 6-transistor cell. 55 ns: 30 mA Standby current < 50 µA at 125 °C The circuit is activated by the falling edge of E. The address and TTL/CMOS-compatible control inputs open simultaneously. Power supply voltage 5 V According to the information of W Operating temperature range -40 °C to 85 °C and G, the data inputs, or outputs, -40 °C to 125 °C are active. In a Read cycle, the data outputs are activated by the QS 9000 Quality Standard falling edge of G, afterwards the ESD protection > 2000 V (MIL STD 883C M3015.7) data word will be available at the outputs DQ0-DQ7. After the Latch-up immunity >100 mA address change, the data outputs Package: SOP28 (300/330 mil) Pin Configuration Pin Description A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 VCC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 Signal Name A0 - A14 DQ0 - DQ7 E G W VCC VSS Signal Description Address Inputs Data In/Out Chip Enable Output Enable Write Enable Power Supply Voltage Ground SOP 22 21 20 19 18 17 16 15 Top View April 20, 2004 1 U62H256A Block Diagram A6 A7 A8 A9 A10 A11 A12 A13 A14 Row Address Inputs Row Decoder Memory Cell Array 512 Rows x 64 x 8 Columns Common Data I/O A0 A1 A2 A3 A4 A5 Column Address Inputs Column Decoder DQ0 Sense Amplifier/ Write Control Logic DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 Address Change Detector Clock Generator VCC VSS E W G Truth Table Operating Mode Standby/not selected Internal Read Read Write * H or L E H L L L W * H H L G * H L * DQ0 - DQ7 High-Z High-Z Data Outputs Low-Z Data Inputs High-Z 2 April 20, 2004 U62H256A Characteristics All voltages are referenced to V SS = 0 V (ground). All characteristics are valid in the power supply voltage range and in the operating temperature range specified. Dynamic measurements are based on a rise and fall time of ≤ 5 ns, measured between 10 % and 90 % of V I, as well as input levels of VIL = 0 V and VIH = 3 V. The timing reference level of all input and output signals is 1.5 V, with the exception of the tdis-times and ten-times, in which cases transition is measured ±200 mV from steady-state voltage. Absolute Maximum Ratings a Power Supply Voltage Input Voltage Output Voltage Power Dissipation Operating Temperature Storage Temperature Output Short-Circuit Current at VCC = 5 V and VO = 0 V c a Symbol VCC VI VO PD Min. -0.5 -0.5 -0.5 -40 -40 -65 Max. 7 VCC + 0.5 b VCC + 0.5 b 1 85 125 150 200 Unit V V V W °C °C mA K-Type A-Type Ta Tstg | IOS | b c Stresses greater than those listed under „Absolute Maximum Ratings“ may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at condition above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability Maximum voltage is 7 V Not more than 1 output should be shorted at the same time. Duration of the short circuit should not exceed 30 s. Recommended Operating Conditions Power Supply Voltage Input Low Voltage d Input High Voltage d Symbol VCC VIL VIH Conditions Min. 4.5 -0.3 2.2 Max. 5.5 0.8 VCC + 0.3 Unit V V V -2 V at Pulse Width 10 ns April 20, 2004 3 U62H256A Electrical Characteristics Supply Current - Operating Mode Symbol ICC(OP) VCC VIL VIH tcW tcW VCC VE K-Type A-Type VCC VE VCC IOH VCC IOL VCC VIH VCC VIL VCC VOH VCC VOL VCC VOH VCC VOL Conditions = = = = = 5.5 V 0.8 V 2.2 V 35 ns 55 ns Min. Max. Unit 90 70 mA mA Supply Current - Standby Mode (CMOS level) ICC(SB) = 5.5 V = VCC - 0.2 V 10 50 1 2.4 0.4 2 -2 -4 8 µA µA mA V V µA µA mA mA Supply Current - Standby Mode (TTL level) Output High Voltage Output Low Voltage Input High Leakage Current Input Low Leakage Current Output High Current Output Low Current Output Leakage Current High at Three-State Outputs Low at Three-State Outputs ICC(SB)1 VOH VOL IIH IIL IOH IOL = 5.5 V = 2.2 V = 4.5 V = -4.0 mA = 4.5 V = 8.0 mA = 5.5 V = 5.5 V = 5.5 V = 0V = = = = 4.5 V 2.4 V 4.5 V 0.4 V IOHZ IOLZ = 5.5 V = 5.5 V = 5.5 V = 0V 2 -2 µA µA 4 April 20, 2004 U62H256A Switching Characteristics Read Cycle Read Cycle Time Address Access Time to Data Valid Chip Enable Access Time to Data Valid G LOW to Data Valid E HIGH to Output in High-Z G HIGH to Output in High-Z E LOW to Output in Low-Z G LOW to Output in Low-Z Output Hold Time from Address Change E LOW to Power-Up Time E HIGH to Power-Down Time Symbol Alt. tRC tAA tACE tOE tHZCE tHZOE tLZCE tLZOE tOH tPU tPD IEC tcR ta(A) ta(E) ta(G) tdis(E) tdis(G) ten(E) ten(G) tv(A) 3 0 3 0 35 Min. 35 Max. Min. 55 Unit Max. 35 35 35 15 15 12 55 55 55 25 20 15 3 0 3 0 55 ns ns ns ns ns ns ns ns ns ns ns Switching Characteristics Write Cycle Write Cycle Time Write Pulse Width Write Setup Time Address Setup Time Address Valid to End of Write Chip Enable Setup Time Pulse Width Chip Enable to End of Write Data Setup Time Data Hold Time Address Hold from End of Write W LOW to Output in High-Z G HIGH to Output in High-Z W HIGH to Output in Low-Z G LOW to Output in Low-Z Symbol Alt. tWC tWP tWP tAS tAW tCW tCW tDS tDH tAH tHZWE tHZOE tLZWE tLZOE IEC tcW tw(W) tsu(W) tsu(A) tsu(A-WH) Min. 35 Max. Min. 55 Unit Max. 35 20 20 0 25 25 25 15 0 0 15 12 0 0 55 35 35 0 40 40 40 25 0 0 20 15 0 0 ns ns ns ns ns ns ns ns ns ns ns ns ns ns tsu(E) tw(E) tsu(D) th(D) th(A) tdis(W) tdis(G) ten(W) ten(G) April 20, 2004 5 U62H256A Data Retention Mode E - controlled VCC VCC(DR) ≥ 2 V 2.2 V 0V tsu(DR) Data Retention trec 2.2 V E 4.5 V VCC(DR) - 0.2 V ≤ VE(DR) ≤ VCC(DR) + 0.3 V Data Retention Characteristics Data Retention Supply Voltage Data Retention Supply Current Symbol Alt. IEC VCC(DR) ICC(DR) VCC(DR) = 3 V VE = VCC(DR) - 0.2 V K-Type A-Type See Data Retention Waveforms (above) 0 tcR Conditions Min. 2 Typ. Max. 5.5 Unit V 6 30 µA µA ns ns Data Retention Setup Time Operating Recovery Time tCDR tR tsu(DR) trec Test Configuration for Functional Check 5V A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 VCC VIH VIL Input level according to the relevant test measurement Simultaneous measurement of all 8 output pins DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 481 VO 30 pF e E W G 255 VSS e In measurement of tdis(E),tdis(W), ten(E), ten(W), ten(G) the capacitance is 5 pF. 6 April 20, 2004 U62H256A Capacitance Input Capacitance Output Capacitance Conditions VCC VI f Ta = 5.0 V = VSS = 1 MHz = 25 °C Symbol CI Co Min. Max. 7 7 Unit pF pF All pins not under test must be connected with ground by capacitors. Ordering Code Example Type Package S = SOP28 (300 mil) S2 = SOP28 (330 mil) Type 2 Operating Temperature Range K = -40 to 85 °C A = -40 to 125 °C U62H256A S K 35 LL Leadfree Option blank = Standard Package G1 = Leadfree Green Package f Power Consumption blank = Standard (only A-Type) LL = Very Low Power (only K-Type) Access Time 35 = 35 ns 55 = 55 ns f on special request Device Marking (example) Product specification Assembly location and trace code Internal Code ZMD U62H256ASK 35LL C 0425 1 ZZ G1 Date of manufacture (The first 2 digits indicating the year, and the last 2 digits the calendar week.) Leadfree Green Package April 20, 2004 7 U62H256A Read Cycle 1: Ai-controlled (during Read Cycle : E = G = V IL, W = VIH) tcR Ai DQi Output Previous Data Valid tv(A) Address Valid ta(A) Output Data Valid Read Cycle 2: G-, E-controlled (during Read Cycle: W = V IH) tcR Ai E G DQi Output High-Z tPU 50 % tsu(A) ten(E) Address Valid ta(E) ta(G) ten(G) tdis(E) tdis(G) Output Data Valid tPD 50 % ICC(OP) ICC(SB) 8 April 20, 2004 U62H256A Write Cycle1: W-controlled tcW Ai E W DQi Input tdis(W) tsu(A) Address Valid tsu(E) tsu(A-WH) tw(W) tsu(D) th(D) th(A) DQi Output Input Data Valid ten(W) High-Z G Write Cycle 2: E-controlled tcW Ai E W DQi Input ten(E) Address Valid tsu(A) tw(E) tsu(W) tsu(D) tdis(W) High-Z tdis(G) th(D) Input Data Valid th(A) DQi Output G undefined L- to H-level H- to L-level The information describes the type of component and shall not be considered as assured characteristics.Terms of delivery and rights to change design reserved. April 20, 2004 9 U62H256A LIFE SUPPORT POLICY ZMD products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the ZMD product could create a situation where personal injury or death may occur. Components used in life-support devices or systems must be expressly authorized by ZMD for such purpose. LIMITED WARRANTY The information in this document has been carefully checked and is believed to be reliable. However Zentrum Mikroelektronik Dresden AG (ZMD) makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon it. The information in this document describes the type of component and shall not be considered as assured characteristics. ZMD does not guarantee that the use of any information contained herein will not infringe upon the patent, trademark, copyright, mask work right or other rights of third parties, and no patent or licence is implied hereby. This document does not in any way extent ZMD’s warranty on any product beyond that set forth in its standard terms and conditions of sale. ZMD reserves terms of delivery and reserves the right to make changes in the products or specifications, or both, presented in this publication at any time and without notice. April 20, 2004 Zentrum Mikroelektronik Dresden AG Grenzstraße 28 • D-01109 Dresden • P. O. B. 80 01 34 • D-01101 Dresden • Germany Phone: +49 351 8822 306 • Fax: +49 351 8822 337 • Email: memory@zmd.de • http://www.zmd.de
U62H256AS2A55LL 价格&库存

很抱歉,暂时无法提供与“U62H256AS2A55LL”相匹配的价格&库存,您可以联系我们找货

免费人工找货