FR106

FR101 THRU FR107 FAST RECOVERY RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere DO-204AL FEATURES * The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 * Fast switching * Low leakage * Low forward voltage drop * High current capability * High surge capability * High reliability 0.107(2.7) 0.080(2.0) DIA. 0.205(5.2) 0.160(4.1) 1.0(25.4) MIN. 1.0(25.4) MIN. MECHANICAL DATA Case : JEDEC DO-204AL molded plastic Terminals : Plated axial leads , solderable per MIL-STD-750, Method 2026 Polarity : Color band denotes cathode end Mounting Position : Any Weight : 0.012 ounes , 0.3 gram 0.034(0.86) 0.028(0.71) DIA. *Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature SYMBOLS unless otherwise specified. Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375" (9.5mm) lead length at TL=75 C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 1.0 A Maximum Full Load Reverse Current Full Cycle average, 0.375" (9.5mm) lead length at TL=55 C Maximum DC reverse current at rated DC blocking voltage Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Operating junction and storage temperature range o o o FR101 50 35 50 FR102 100 70 100 FR103 200 140 200 FR104 400 280 400 FR105 600 420 600 FR106 800 560 800 FR107 1000 700 1000 UNITS Volts Volts Volts Amps VRRM VRMS VDC I(AV) 1.0 IFSM VF IR(AV) 30 1.3 100 Amps Volts uA TA=25 C o IR trr CJ TJ,TSTG 150 5.0 250 15 -65 to +150 500 uA nS pF o C NOTES : (1) Reverse recovery test condition : IF 0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts REV. : 0 Zowie Technology Corporation RATINGS AND CHARACTERISTIC CURVES FR101 THRU FR107 FIG.1 - FORWARD CURRENT DERATING CURVE 1.2 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 1.0 0.8 0.6 0.4 0.2 0.375" (9.5mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 PEAK FORWARD SURGE CURRENT, AMPERES 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 40 30 20 10 0 0 25 50 75 100 125 o 0 150 175 1 10 NUMBER OF CYCLES AT 60Hz 100 AMBIENT TEMPERATURE, C FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10.00 IINSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 10 FIG.4 - TYPICAL REVERSE CHARACTERISTICS PULSE WIDTH=300uS 1% DUTY CYCLE 1.00 1.0 0.1 TJ=25 C o 0.10 0.01 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,% FIG.5 - TYPICAL JUNCTION CAPACITANCE 200 JUNCTION CAPACITANCE, pF TJ = 25 C 50 NONINDUCTIVE 10 NONINDUCTIVE o FIG.6 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, VOLTS (+) 25 Vdc ( approx ) (-) D.U.T. +0.5A (-) PULSE GENERATOR ( NOTE 2 ) trr 0 -0.25A 1 NONINDUCTIVE OSCILLOSCOPE ( NOTE 1 ) (+) -1.0A NOTES : 1. Rise Time = 7ns max. Input Impedance= 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance= 50 ohms. SET TIME BASE FOR 50/100 ns/cm REV. : 0 Zowie Technology Corporation