GBU6K

GBU6A THRU GBU6M GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes GBU FEATURES * * * * * Glass passivated chip junctions High case dielectric strength of 1500VRMS High surge overload rating Ideal for printed circuit boards Plastic package has underwriters laboratory flammability classification 94V-0 * This series is UL listed under recognized component index, file number E54214 o * High temperature soldering quaranteed:260 C/10 seconds 0.375" (9.5mm) lead length, 5lbs. (2.3kg) tension 0.740(18.80) 0.720(18.30) 0.125(3.2)X45 CHAMFER 0.310(7.90) 0.290(7.40) o 0.880(22.30) 0.860(21.80) 0.140(3.56) 0.130(3.30) 0.160(4.10) 0.140(3.50) 0.020 R(TYP.) 9 TYP. 5 TYP. 0.040(1.02) 0.030(0.76) o o 0.075(1.9)R. 0.710(18.00) 0.080(2.03) 0.065(1.65) 0.190(4.83) 0.210(5.33) 0.080(2.03) 0.060(1.52) 0.690(17.50) 0.085(2.16) 0.065(1.65) 0.100(2.54) 0.085(2.16) 0.022(0.56) 0.018(0.46) MECHANICAL DATA Case : Molded plastic body over passivated chip Terminals : Plated Leads, solderable per MIL-STD-750, Method 2026 Mounting Position : Any (NOTE 2) Mounting torque : 5.0 in-lbs maximum Weight : 0.15 ounce, 4.0 grams *Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified output current at TC=100 C (NOTE 2,3) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) TJ=150 C Maximum instantaneous forward voltage at 6.0 A Maximum DC reverse current at rated DC blocking voltage Rating for fusing ( t < 8.3ms ) Typical junction capacitance per element (NOTE 1) Typical thermal resistance (NOTE 2,3) Operating junction and storage temperature range @TC=25 C @TC=125 C o o o o o SYMBOLS VRRM VRMS VDC I (AV) GBU6A 50 35 50 GBU6B 100 70 100 GBU6D 200 140 200 GBU6G 400 280 400 GBU6J 600 420 600 GBU6K 800 560 800 GBU6M 1000 700 1000 UNITS Volts Volts Volts Amps 6.0 IFSM 175 Amps VF IR I2t CJ R R JA JC 1.0 5.0 500 127 211 7.4 2.2 -55 to +150 94 Volts uA As pF o 2 C/W o TJ,TSTG C NOTES : (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 V DC. (2) Units case mounted on 2.6 x 1.4 x 0.06" thick (6.5 x 3.5 x 0.15 cm) Al. Plate heatsink (3) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screws REV. : 0 Zowie Technology Corporation RATINGS AND CHARACTERISTIC CURVES GBU6A THRU GBU6M FIG.1 - FORWARD CURRENT DERATING CURVE 6.0 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES Heat-Sink Mounting, 2.6 x 1.4 x 0.06" thk (6.5 x 3.5" x .15cm) AL. PLATE FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 175 PEAK FORWARD SURGE CURRENT, AMPERES 150 125 100 75 50 1.0 CYCLE TJ=25 C Single Sine-Wave (JEDEC Method) o 4.0 2.0 60 Hz Resistive or inductive load 0 20 25 40 60 80 100 120 o 140 160 1 10 NUMBER OF CYCLES AT 60Hz 100 AMBIENT TEMPERATURE, C FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10.00 IINSTANTANEOUS FORWARD CURRENT, AMPERES FIG.4 - TYPICAL REVERSE CHARACTERISTICS PER BRIDGE ELEMENT INSTANTANEOUS REVERSE CURRENT, MICROAMPERES PULSE WIDTH=300uS 1% DUTY CYCLE 100 TJ=125 C o 1.00 10 0.10 1.0 0.1 TJ=25 C o 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,% INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1000 JUNCTION CAPACITANCE, pF TRANSIENT THERMAL IMPEDANCE( C/W) FIG.5 - TYPICAL JUNCTION CAPACITANCE TJ = 25 C o FIG.6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 o 10 100 1 10 .1 .2 50-400V 600V-1000V .4 1.0 2 4 10 20 40 100 0.1 0.01 0.10 1.0 t , HEATING TIME, sec 10 100 REVERSE VOLTAGE, VOLTS REV. : 0 Zowie Technology Corporation