KPT-3216EC

3.2mmx1.6mm SMD CHIP LED LAMP Part Number: KPT-3216EC Features High Efficiency Red Description 3.2mmx1.6mm SMD LED, 0.75mm thickness. The High Efficiency Red source color devices are made with Low power consumption. Gallium Arsenide Phosphide on Gallium Phosphide Orange Wide viewing angle. Light Emitting Diode. Ideal for backlight and indicator. Package : 2000pcs / reel. Moisture sensitivity level : level 3. RoHS compliant. Package Dimensions K g in ig r b t h Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAB1539 REV NO: V.14A DATE: MAY/27/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203001913 Selection Guide Part No. Emitting Color (Material) Iv (mcd) [2] @ 20mA Lens Type Viewing Angle [1] Min. High Efficiency Red (GaAsP/GaP) 8 15 *3 KPT-3216EC Typ. *8 Water Clear 2θ1/2 160° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength High Efficiency Red Dominant Wavelength High Efficiency Red 617 Δλ1/2 Spectral Line Half-width High Efficiency Red 45 C Capacitance High Efficiency Red 15 VF [2] Forward Voltage IR Reverse Current t h 627 λD [1] Max. Units Test Conditions nm IF=20mA nm IF=20mA nm IF=20mA pF VF=0V;f=1MHz 2.5 V IF=20mA 10 uA VR=5V ig r b g in High Efficiency Red 2 High Efficiency Red Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. K Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 160 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAB1539 REV NO: V.14A DATE: MAY/27/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203001913 High Efficiency Red KPT-3216EC K g in ig r b t h SPEC NO: DSAB1539 REV NO: V.14A DATE: MAY/27/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203001913 KPT-3216EC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) K ig r b t h Reel Dimension g in Tel 13751197819 SPEC NO: DSAB1539 REV NO: V.14A DATE: MAY/27/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203001913 PACKING & LABEL SPECIFICATIONS KPT-3216EC t h ig r b g in K Tel 13751197819 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes SPEC NO: DSAB1539 REV NO: V.14A DATE: MAY/27/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203001913