5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Product specification
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Features
For surface mounted applications in order to optimize board
space
Low profile package
Built-in strain relief
Glass passivated junction
Low inductance
Excellent clamping capability
Mechanical Data
Case: JEDEC DO-214AB. Molded plastic over glass
passivated junction
Terminal: Solder plated, solderable per
MIL-STD-750, Method 2026
Polarity: Color band denotes cathode except
bi-directional models
Standard Packaging: 16mm tape (EIA STD RS-481)
Weight: 0.30g
5000W peak pulse power capability at 10/1000μswaveform,
repetition rate (duty cycle): 0.01%
Applications
Fast response time
Typical IR
less than 2μA above 22V
High Temperature soldering: 260℃/10 seconds at terminals
Plastic package has underwriters laboratory flammability
94V-0
Meets MSL level 1, per J-STD-020
Safety certification:
I/O interface
AC/DC power supply
Low frequency signal transmission line (RS232,
RS485, etc.)
UL: E244458
Reference News
PACKAGE OUTLINE
PIN CONFIGURATION
SMC(DO-214AB) Unipolar
SMC(DO-214AB) Bipolar
Copyright© Msksemi Incorporated
www.msksemi.com
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Ratings at 25℃ ambient temperature unless otherwise specified.
Rating
Symbol
Value
Units
Peak pulse power dissipation at 10/1000μs waveform
(Note1, Note2, Fig.1)
PPPM
Minimum 5000
Watts
Peak pulse current of at 10/1000μs waveform (Note 1, Fig.3)
IPPM
See Table
Amps
PM(AV)
6.5
Watts
IFSM
300
Amps
TJ,TSTG
-55 to +150
℃
Typical thermal resistance junction to lead
RθJL
15
℃/W
Typical thermal resistance junction to ambient
RθJA
75
℃/W
Steady state power dissipation at TA=50℃ (Fig.5)
Peak forward surge current, 8.3ms single half sine-wave
superimposed on rated load, (JEDEC Method) (Note3, Fig.6)
Operating junction and Storage Temperature Range.
Notes: 1. Non-repetitive current pulse, per Fig.3 and derated above TA=25℃ per Fig.2.
2. Mounted on 8.0mm×8.0mm copper pads to each terminal.
3. 8.3ms single half sine-wave, or equivalent square wave, duty cycle=4 pulses per minutes maximum.
Electrical Characteristics (TA=25℃)
Part Number
Unidirectional Bidirectional
Device
Marking
Code
Reverse
Stand-Off
Voltage
Breakdown
Voltage
@IT
Test
Current
Maximum
Clamping
Voltage
@IPP
Peak
Reverse
Pulse Leakage
Current @ VRWM
UNI
BI
VRWM(V)
VBR(V)
IT(mA)
VC(V)
IPP(A)
IR(μA)
5.0SMDJ11A
5.0SMDJ11CA
5PEN
5BEN
11.0
12.20~13.50
10
18.2
275.00
800
5.0SMDJ12A
5.0SMDJ12CA
5PEP
5BEP
12.0
13.30~14.70
10
19.9
252.00
800
5.0SMDJ13A
5.0SMDJ13CA
5PEQ
5BEQ
13.0
14.40~15.90
10
21.5
233.00
500
5.0SMDJ14A
5.0SMDJ14CA
5PER
5BER
14.0
15.60~17.20
10
23.2
216.00
200
5.0SMDJ15A
5.0SMDJ15CA
5PES
5BES
15.0
16.70~18.50
1
24.4
205.00
100
5.0SMDJ16A
5.0SMDJ16CA
5PET
5BET
16.0
17.80~19.70
1
26.0
193.00
50
5.0SMDJ17A
5.0SMDJ17CA
5PEU
5BEU
17.0
18.90~20.90
1
27.6
181.00
20
5.0SMDJ18A
5.0SMDJ18CA
5PEV
5BEV
18.0
20.00~22.10
1
29.2
172.00
10
5.0SMDJ20A
5.0SMDJ20CA
5PEW
5BEW
20.0
22.20~24.50
1
32.4
155.00
5
5.0SMDJ22A
5.0SMDJ22CA
5PEX
5BEX
22.0
24.40~26.90
1
35.5
141.00
5
5.0SMDJ24A
5.0SMDJ24CA
5PEZ
5BEZ
24.0
26.70~29.50
1
38.9
129.00
2
5.0SMDJ26A
5.0SMDJ26CA
5PFE
5BFE
26.0
28.90~31.90
1
42.1
119.00
2
5.0SMDJ28A
5.0SMDJ28CA
5PFG
5BFG
28.0
31.10~34.40
1
45.4
110.00
2
5.0SMDJ30A
5.0SMDJ30CA
5PFK
5BFK
30.0
33.30~36.80
1
48.4
103.00
2
Copyright© Msksemi Incorporated
www.msksemi.com
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Part Number
Unidirectional Bidirectional
Device
Marking
Code
Reverse
Stand-Off
Voltage
Breakdown
Voltage
@IT
Test
Current
Maximum
Clamping
Voltage
@IPP
Peak Reverse
Pulse Leakage
Current @ VRWM
UNI
BI
VRWM(V)
VBR(V)
IT(mA)
VC(V)
IPP(A)
IR(μA)
5.0SMDJ33A
5.0SMDJ33CA
5PFM
5BFM
33.0
36.70~40.60
1
53.3
93.90
2
5.0SMDJ36A
5.0SMDJ36CA
5PFP
5BFP
36.0
40.00~44.20
1
58.1
86.10
2
5.0SMDJ40A
5.0SMDJ40CA
5PFR
5BFR
40.0
44.40~49.10
1
64.5
77.60
2
5.0SMDJ43A
5.0SMDJ43CA
5PFT
5BFT
43.0
47.80~52.80
1
69.4
72.10
2
5.0SMDJ45A
5.0SMDJ45CA
5PFV
5BFV
45.0
50.00~55.30
1
72.7
68.80
2
5.0SMDJ48A
5.0SMDJ48CA
5PFX
5BFX
48.0
53.30~58.90
1
77.4
64.70
2
5.0SMDJ51A
5.0SMDJ51CA
5PFZ
5BFZ
51.0
56.70~62.70
1
82.4
60.70
2
5.0SMDJ54A
5.0SMDJ54CA
5PGE
5BGE
54.0
60.00~66.30
1
87.1
57.50
2
5.0SMDJ58A
5.0SMDJ58CA
5PGG
5BGG
58.0
64.40~71.20
1
93.6
53.50
2
5.0SMDJ60A
5.0SMDJ60CA
5PGK
5BGK
60.0
66.70~73.70
1
96.8
51.70
2
5.0SMDJ64A
5.0SMDJ64CA
5PGM
5BGM
64.0
71.10~78.60
1
103.0
48.60
2
5.0SMDJ70A
5.0SMDJ70CA
5PGP
5BGP
70.0
77.80~86.00
1
113.0
44.30
2
5.0SMDJ75A
5.0SMDJ75CA
5PGR
5BGR
75.0
83.30~92.10
1
121.0
41.40
2
5.0SMDJ78A
5.0SMDJ78CA
5PGT
5BGT
78.0
86.70~95.80
1
126.0
39.70
2
5.0SMDJ85A
5.0SMDJ85CA
5PGV
5BGV
85.0
94.40~104.00
1
137.0
36.50
2
5.0SMDJ90A
5.0SMDJ90CA
5PGX
5BGX
90.0
100.00~111.00
1
146.0
34.30
2
5.0SMDJ100A
5.0SMDJ100CA
5PGZ
5BGZ
100.0
111.00~123.00
1
162.0
30.90
2
5.0SMDJ110A
5.0SMDJ110CA
5PHE
5BHE
110.0
122.00~135.00
1
177.0
28.30
2
5.0SMDJ120A
5.0SMDJ120CA
5PHG
5BHG
120.0
133.00~147.00
1
193.0
26.00
2
5.0SMDJ130A
5.0SMDJ130CA
5PHK
5BHK
130.0
144.00~159.00
1
209.0
24.00
2
5.0SMDJ150A
5.0SMDJ150CA
5PHM
5BHM
150.0
167.00~185.00
1
243.0
20.60
2
5.0SMDJ160A
5.0SMDJ160CA
5PHP
5BHP
160.0
178.00~197.00
1
259.0
19.30
2
5.0SMDJ170A
5.0SMDJ170CA
5PHR
5BHR
170.0
189.00~209.00
1
275.0
18.20
2
Notes: For bidirectional type having VRWM of 18V and less, the IR limit is double.
Copyright© Msksemi Incorporated
www.msksemi.com
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Ratings and Characteristic Curves (TA=25℃ unless otherwise noted)
Figure 2. Pulse Derating Curve
Peak Pulse Power (P PP ) or Current (I PP )
Derating in Percentage %
Figure 1. Peak Pulse Power Rating Curve
PPPM - Peak Pulse Power (kW)
1000
100
10
1
0.31×0.31 ″(8.0×8.0mm)
Copper Pad Area
0.1
0.1
1
100
10
100
80
60
40
20
0
1000
0
td-Pulse Width (µs)
125
150
175
100000
Uni-directional
10000
Cj (pF)
IPPM - Peak Pulse Current, %I RSM
100
Peak Value I PPM
100
Half Value I PPM (IPPM /2)
1000
Bi-directional
100
50
10/1000µs Waveform
as defined by R.E.A
10
td
0
0
Measured at
1MHz, 100mV, 0V bias
1
1.0
2.0
3.0
1
4.0
t-Time (ms)
Figure 5. Steady State Power Dissipation Derating
IFSM - Peak Forward Surve Current (A)
6
5
4
3
2
1
0
25
1000
Surge Current Uni-Directional Only
7
0
10
100
VRWM -Reverse Stand-Off Voltage (V)
Figure 6. Maximum Non-Repetitive Forward
Curve
PM(AV), Steady State Power Dissipation (W)
75
Figure 4. Typical Junction Capacitance
TJ=25℃
Pulse Width(t d) is defined as
the point where the peak
current decays to 50% of I PPM
tr=10µs
50
TA-Ambient Temperature ( ℃)
Figure 3. Pulse Waveform
150
25
50
75
100
125
TA-Ambient Temperature ( ℃)
Copyright© Msksemi Incorporated
150
175
350
300
250
200
150
100
50
0
1
10
Number of Cycles at 60Hz
100
www.msksemi.com
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Recommended Soldering Conditions
Reflow Soldering
Critical Zone
TL to TP
tP
TP
Ramp-up
TL
tL
Temperature
TS max
TS min
Ramp-down
tS
Preheat
25
t 25℃ to Peak
Time
Recommended Conditions
Profile Feature
Pb-Free Assembly
Average ramp-up rate (TL to TP)
3℃/second max.
Preheat
-Temperature Min (TS min)
-Temperature Max (TS max)
-Time (min to max) (tS)
150℃
200℃
60-180 seconds
TS max to TL
-Ramp-up Rate
Time maintained above:
-Temperature (TL)
-Time (tL)
Peak Temperature (TP)
Time within 5℃ of actual Peak Temperature (tP)
Ramp-down Rate
Time 25℃ to Peak Temperature
Copyright© Msksemi Incorporated
3℃/second max.
217℃
60-150 seconds
260℃
20-40 seconds
6℃/second max.
8 minutes max.
www.msksemi.com
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Dimensions (SMC/DO-214AB)
Product:
Symbol
Cathode Band
D1 D
L
H1 H
d
T1
T
3.20mm
Pad:
1.75mm
4.69mm
1.75mm
Millimeters
Inches
Min.
Max.
Min.
Max.
L
6.60
7.11
0.
0.
D
5.59
6.22
2600.
2800.
D1
2.90
3.20
2200.
2450.
T
7.75
8.13
1140.
1260.
T1
0.76
1.52
3050.
3200.
d
-
0.203
030
-
0600.
H
2.20
2.80
0.087
0080.
H1
2.06
2.62
0.079
0.103
REELSPECIFICATION
P/N
PKG
QTY
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
SMC
3000
Copyright© Msksemi Incorporated
www.msksemi.com
5.0SMDJ11(C)A - 5.0SMDJ170(C)A
Attention
■ Any and all MSKSEMI Semiconductor products described or contained herein do not
handle applications that require extremely high levels of reliability, such as life-support
have specifications
that can
systems, aircraft's control systems, or
other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with
your MSKSEMI Semiconductor representative
nearest
you before using any MSKSEMI Semiconductor products described
or contained herein in such applications.
■ MSKSEMI Semiconductor assumes no responsibility for equipment failures that result from using products
at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in
products specificationsof any andall MSKSEMI Semiconductor products described orcontained herein.
■ Specifications of any and all MSKSEMI Semiconductor products described or contained herein stipulate the
performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the
performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To
verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test
devices mounted in the customer’sproducts orequipment.
■ MSKSEMI Semiconductor. strives to supply high-quality high-reliability products. However, any and all semiconductor
products fail with someprobability. It is possiblethat these probabilistic failures could give rise to accidents or events that could
endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing
equipment, adopt safety measures so that these kinds of accidents
or events cannot occur. Such measures include but are
not limited to protective circuits anderror prevention circuitsfor safedesign, redundant design, and structural design.
■ In the event that any or all MSKSEMI Semiconductor products(including technical data, services) described
or contained
herein are controlled under any of applicable local export control laws and regulations, such products must not be exported
without obtaining the export license from theauthorities
concerned
in accordance with the above law.
■ No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior
written permission of MSKSEMI Semiconductor.
■
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume
production. MSKSEMI Semiconductor believes information herein is accurate and
reliable, but no guarantees are made or
implied regarding its use or any infringementsof intellectual property rights or other rightsof third parties.
■
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. Whendesigning equipment, referto the "Delivery Specification" for the MSKSEMI
Semiconductor productthat you intend to use.
Copyright© Msksemi Incorporated
www.msksemi.com