3602-021613-619A

3602 Series Mechanical Totalizing Counter This unit counts revolutions on many different types of production machinery. Robustly constructed for continuous operation at high speeds with the main shaft running in double oil impregnated bearings to ensure accurate, long term, trouble free service. It is supplied with a double drive with wing bush, customer configurable reset. Key Features • 6-digit 6.4mm (0.25in) readout • Up to 3000 counts per minute with 1:1 gear ratio • 1:1, 1:10, 2:1, 3:1, 4:1 gearings as standard • Front viewing • Reset to zero • Reset by lever • Customer Configurable Reset Specifications Display Base Material White on black, decimals black on white 0.25in (6.4mm) figures Black PC-ABS plastic Cover Material Grey ABS plastic Drive Shaft Diameter 0.275 inch (7mm) diameter Gearing Bearings 1:1, 1:10, 2:1, 3:1, 4:1 as standard. Others on application Bronze, oil impregnated for life Operating Torque 180g.cm (2.5oz.in) at 1:1 gearing Maximum Shaft Speed 3000 RPM Maximum Count Speed 3000 CPM Accuracy +/- 1% Operating Temp -10°C to +50°C [14°F to 122°F] Storage Temp -20°C to +50°C [-4°F to 122°F] Environmental Protection IP40 Nett Weight 200g Measuring Wheel Ordering Information Material Width 12” circumference 18” circumference 1/3m circumference 1/2m circumference Rubber Covered Plastic 5/8” (16mm) 007571 007573 007905 007574 Knurled Aluminum 5/8” (16mm) 001558 001622 Part Number Ordering Chart COUNTER TYPE 3602FRONT VIEWING NUMBER OF DECIMAL PLACES FIG WHEEL READING GEAR RATIO 0 NO DECIMAL PLACES 0 FULL FIGURES (PLAIN) 0 1 1 0 - 11” FIG WHEEL (FEET & INCHES) 1 1:1 2 0 - 9” FIG WHEEL (FEET & TENTHS) 2 2:1 3 0 - 9” FIG WHEEL (YARDS & TENTHS) 3 3:1 RESET POSITION IS CUSTOMER SELECTIVE 4 4 4:1 DOUBLE DRIVE SHAFT WITH WING BUSHES FITTED AS STANDARD FULL FIGURES (FEET) 5 FULL FIGURES (YARDS) 5 1:25 6 FULL FIGURES (METRES) 6 10:1 7 0 - 7/8” FIG WHEEL (YARDS & EIGTHS) 7 2:3 8 128:105 9 64:105 ONE DECIMAL PLACE ALL COUNTERS ARE 6 DIGIT EXAMPLE OF CODING: 3602 - 117TG 3602 = FRONT VIEWING 1 = ONE DECIMAL PLACE 1 = 0-11” FIG WHEEL (FEET & INCHES) 7 = 2:3 TG = TOP GOING 3602-117TG = 99999 - 11 / 2:3 / TOP GOING 9 0 - 9cm FIG WHEEL WITH 100 LINES(M/cm) www.trumeter.com Trumeter (The Americas) 6601 Lyons Rd, Suite H-7 Coconut Creek, Florida FL 33073, USA Tel: +1 954 725 6699 Email: sales.usa@trumeter.com 1:10 DRIVE DIRECTION TC TOP COMING Material Direction (Top Coming) Trumeter (Europe) Pilot Mill Alfred Street Bury, BL9 9EF Tel: +44 161 674 0960 Email: sales.uk@trumeter.com 5 TG 2 9 8 9 0 TOP GOING 5 2 9 8 9 0 Material Direction (Top Going) Innovative Design Technologies Sdn. Bhd Lot 5881, Lorong Iks Bukit Minyak 1 Taman Perindustrian Iks, 14000 Bukit Tengah Penang, Malaysia Web: www.idtworld.com Tel: + 604 5015700 Email: sales.my@idtworld.com 3602-DS-3.1 06/2021