211051

Concrete drills SDS-plus hammer drills Cutting edge: Point angle: Soldering: Shank: strong special tungsten carbide plate in special alloying 130° high-performance special soldering SDS-plus design Highest solidity of the hammer drill is guaranteed by a strengthening of the core, therefore maximum power transmission. High capacity of resistance to wear on the basic of special hardening-blastening. Grooves for optimum removal of bore dust. Suitable for mounting parts. Applications: for drilling in granite, concrete, clinker, stone, masonry, tiles and marble. Suitable in all hammer drills with SDS-plus adaptor and 2-groove-adaptor as i. e. Hilti TE 10-22. Packaging: in plastic clip of 1 each 2.1 Ø mm Ø inch 3,5 4,0 4,0 5,0 5,0 5,0 5,5 5,5 6,0 6,0 6,0 6,0 6,0 6,5 6,5 6,5 6,5 7,0 7,0 7,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 9,0 9,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 11,0 11,0 11,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 13,0 9/64 5/32 5/32 3/16 3/16 3/16 7/32 7/32 15/64 15/64 15/64 15/64 15/64 8/32 8/32 8/32 8/32 9/32 9/32 9/32 5/16 5/16 5/16 5/16 5/16 5/16 5/16 11/32 11/32 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 7/16 7/16 7/16 15/32 15/32 15/32 15/32 15/32 15/32 15/32 1/2 Total length mm 110 110 160 110 160 210 110 160 110 160 210 260 460 110 160 210 260 110 160 210 110 160 210 260 310 460 610 160 210 110 160 210 260 310 360 460 610 1000 160 210 260 160 210 260 310 460 600 1000 160 Working length mm 50 50 100 50 100 150 50 100 50 100 150 200 * 400 50 100 150 200 50 100 150 50 100 150 200 250 * 400 * 550 100 150 50 100 150 200 250 300 * 400 * 550 * 950 100 150 200 100 150 200 250 * 400 * 550 * 950 100 Article no. Price / each € 211 035 211 040 211 041 211 050 211 051 211 052 211 055 211 056 211 060 211 061 211 062 211 063 211 068 211 065 211 066 211 067 211 069 211 070 211 071 211 072 211 080 211 081 211 082 211 083 211 085 211 084 211 086 211 090 211 091 211 105 211 100 211 101 211 102 211 104 211 103 211 106 211 107 211 108 211 110 211 111 211 112 211 120 211 122 211 121 211 124 211 123 211 125 211 126 211 130 * Please note when using these bits it is recommended to pre-drill with a shorter hammer drill of a same diameter. Mostly required diameters are emphasized in extra-bold letters. - 208 - This Certification mark guarantees that our hammer drills are manufactured in compliance with the rules and regulations of the „Institute of Structural Engineering“ and are usable for the manufacturing of dowel-holes. ®