PRODUCT SPECIFICATION
SPEC. NO:
新弘智
T-0619-028X
DATE:Aug.7,2018
CUSTOMER'S PRODUCT NAME:
EMTEK PRODUCT NAME:
HSC1206-Series
THIS SPECIFICATION IS:
□ FULLY ACCEPTED
□ DENIED
□ ACCEPTED UNDER THE FOLLOWING CONDITIONS
SIGNATURE:
NAME(PRINT):
TITLE:
本文件內容全部或部份,未經兆欣科技股份有限公
司同意不得以任何形式複製或其他用途
All rights reserved.This document or parts thereof,may
not be reproduced by any means or used in any manner
witout written permission of EMTEK CO.,LTD.
DATE:
FACTORY:
39,Chingao Rd.,(305)Hsinpu,
Hsinchu Hsien,Taiwan,R.O.C
TEL: 03-5894-433
FAX: 03-5894-523
1/10
SPEC. NO.
PRODUCT SPECIFICATION
T-0619-028X
1. Scope
This specification applies Ceramic Chip Inductance HSC1206-Series
to be delivered to user.
2. Product Identification
HSC 1206 - R62 □ - T
(1) (2) (3) (4) (5)
(1) Dimemsion
(2) Type
(3) Inductance
R62 : 620 nH
(4) Tolerance
G=±2%,J=±5%,K=±10%
(5) Taping Type
3. Shapes and Dimensions
A max. : 3.56 mm
B max. : 2.16 mm
C max. : 1.52 mm
D ref.
E:
: 0.51 mm
0.51
mm
Equivalent circuit
No Polarity
Drawn by
Checked by
Approved by
2/10
SPEC. NO.
PRODUCT SPECIFICATION
T-0619-028X
4. Electrical Characteristics
Customer
Part Number
Our Product
Part Number
Inductance Inductance
(nH)/MHz Tolerance
Q
/MHz
Min.
SRF
(MHz)
Min.
Rdc
(Ω)
Max.
Irms
(mA)
Max.
1st
2nd
3rd
Color Coding
HSC1206-6N8□-T
6.8/100
J,K
30/300
5500
0.07
1000
Blue
Gray
Black
HSC1206-8N2□-T
8.2/100
J,K
15/300
3200
0.18
1000
Black
Gray
Black
HSC1206-10N□-T
10/100
J,K
40/300
4000
0.08
1000
Brown
Black
Black
HSC1206-12N□-T
12/100
J,K
40/300
3200
0.08
1000
Brown
Red
Black
HSC1206-15N□-T
15/100
J,K
40/300
3200
0.10
1000
Brown
Green
Black
HSC1206-22N□-T
22/100
J,K
50/300
2200
0.10
1000
Red
Red
Black
HSC1206-24N□-T
24/100
J,K
50/300
2000
0.10
1000
Red
Yellow
Black
HSC1206-27N□-T
27/100
G,J,K
50/300
1800
0.11
1000
Red
Violet
Black
HSC1206-33N□-T
33/100
J,K
55/300
1800
0.14
1000
Orange Orange
Black
HSC1206-39N□-T
39/100
J,K
55/300
1800
0.12
1000
Orange White
Black
HSC1206-47N□-T
47/100
G,J,K
55/300
1500
0.19
1000
Yellow Violet
Black
HSC1206-56N□-T
56/100
J,K
55/300
1450
0.22
1000
Green
Blue
Black
HSC1206-62N□-T
62/100
J,K
55/300
1200
0.20
1000
Blue
Red
Black
HSC1206-68N□-T
68/100
J,K
55/300
1200
0.27
900
Blue
Gray
Black
HSC1206-82N□-T
82/100
J,K
55/300
1150
0.26
860
Gray
Red
Black
HSC1206-91N□-T
91/100
J,K
55/300
1100
0.24
900
White
Brown
Black
HSC1206-R10□-T
100/100
J,K
55/300
1100
0.26
850
Brown
Black
Brown
HSC1206-R12□-T
120/100
J,K
60/300
1100
0.32
800
Brown
Red
Brown
HSC1206-R15□-T
150/100
J,K
60/300
950
0.36
750
Brown
Green
Brown
HSC1206-R18□-T
180/50
G,J,K
60/300
900
0.43
700
Brown
Gray
Brown
HSC1206-R22□-T
220/50
J,K
60/300
760
0.50
670
Red
Red
Brown
HSC1206-R27□-T
270/50
G,J,K
55/300
730
0.56
630
Red
Violet
Brown
HSC1206-R30□-T
300/50
G,J,K
45/150
700
0.58
600
Orange
Black
Brown
3/10
SPEC. NO.
PRODUCT SPECIFICATION
T-0619-028X
4. Electrical Characteristics
Customer
Part Number
Our Product
Part Number
Inductance Inductance
(nH)/MHz Tolerance
Q
/MHz
Min.
SRF
(MHz)
Min.
Rdc
(Ω)
Max.
Irms
(mA)
Max.
Color Coding
1st
2nd
3rd
HSC1206-R33□-T
330/50
G,J,K
45/150
650
0.62
590
Orange Orange Brown
HSC1206-R36□-T
360/50
J,K
45/150
600
0.65
550
Orange
Blue
Brown
HSC1206-R39□-T
390/50
G,J,K
45/150
600
0.75
530
Orange White
Brown
HSC1206-R43□-T
430/50
J,K
47/150
600
1.25
510
Yellow Orange Brown
HSC1206-R47□-T
470/50
G,J,K
47/150
550
1.30
490
Yellow Violet
Brown
HSC1206-R56□-T
560/35
G,J,K
45/150
470
1.45
460
Green
Blue
Brown
HSC1206-R62□-T
620/35
G,J,K
45/150
465
1.52
455
Blue
Red
Brown
HSC1206-R68□-T
680/35
G,J,K
45/150
460
1.55
450
Blue
Gray
Brown
HSC1206-R75□-T
750/35
J,K
45/150
440
2.25
320
Violet
Green
Brown
HSC1206-R82□-T
820/35
J,K
45/150
420
1.82
400
Gray
Red
Brown
HSC1206-R91□-T
910/35
J,K
45/150
410
2.75
350
White
Brown Brown
HSC1206-1R0□-T
1000/35
J,K
45/150
400
2.80
320
Brown
Black
Red
HSC1206-1R2□-T
1200/35
J,K
45/150
380
3.20
300
Brown
Red
Red
J,K
25/25.2
200
3.90
300
Brown
Gray
Red
HSC1206-1R8□-T 1800/7.96
1. All specifications are calibrated with Coilcraft 1206CS series
2. When ordering, please specify tolerance and packaging codes. Ex: HSC1206-R62G-T
Tolerance :G=±2%,J = ±5%,K=±10%
Packaging : Clear tape and reel { standard }. *
3. L , Q , SRF: Agilent E4991A RF Impedance/Material Analyzer+ Agilent 16197A Test Fixtures
(The electrical specification test by the smallest gap position), or equivalent
4. Rdc : Chroma 16502 Milliohm meter, or equivalent.
5. Irms for a 25℃ rise above 25℃ ambient.
6. Operating temperature range from -40℃ to 125℃.
* Parts/Reel: 7” 2,000 Tape Width: 8mm
4/10
PRODUCT SPECIFICATION
SPEC. NO.
T-0619-028X
Ls V.S Frequency
HSC1206-R82J-T
HSC1206-R36J-T
HSC1206-47NJ-T
HSC1206-15NJ-T
HSC1206-R12J-T
Inductance(μH)
10
1
0.1
0.01
1
10
Frequency(MHz)
100
1000
Q V.S Frequency
HSC1206-R82J-T
HSC1206-R36J-T
HSC1206-R12J-T
HSC1206-47NJ-T
HSC1206-15NJ-T
1000
100
Q
10
1
1
10
Frequency(MHz)
100
1000
5/10
PRODUCT SPECIFICATION
5. Material list
Item
Material
Core
Al2O3 96%
Wire
Copper wire
Epoxy
UV Epoxy
SPEC. NO.
T-0619-028X
6/10
PRODUCT SPECIFICATION
SPEC. NO.
T-0619-028X
6. Reliability Test
Item
Solderability
Specifications
Test conditions
The metalized area must have 90%
Dip pads in flux and dip in solder pot( 96.5 Sn/3.5 Ag
minimum solder coverage.
solder) at 255°C ±5°C.
Resistance to
There must be no case deformation or
Inductors shall be reflowed onto a PC board using
soldering heat
change in dimensions.
96.5 Sn/3.5 Ag solder paste.
Inductance must not change more than
Solder process shall be at a maximum temperature
the stated tolerance.
of 260°C.
For 96.5 Sn/3.5 Ag solder paste:>217°C for 90 seconds
There must be no case deformation or
change in dimensions.
Inductance must not change more than
the stated tolerance.
Solder specimen inductor on the test printed circuit
board. Apply vibrations in each of the x,y and z
directions for 2 hours for a total of 6 hours.
High
temperature
resistance
There must be no case deformation or
change in dimensions.
Inductance must not change more than
the stated tolerance.
Inductors shall be subjected to temperature 125±2℃
for 50±12 hours.
Static
Humidity
Inductors must not have a shorted or
openwinding.
Inductors shall be subjected to temperature 85±2℃
and 90 to 95%RH. for ten 24-hours.
Vibration
Frequency : 10~50 Hz
Amplitude : 1.5mm
Measure the test items after leaving the inductors at
room temperature and humidity for 2 hours.
Measure the test items after leaving the inductors
at room temperature and humidity for 2 hours.
Component
adhesion
(push test)
Inductors shall be subjected to 1.8Kg
Inductors shall be reflow soldered (255°C ±5°C for
10 seconds) to a tinned copper substrate.
A force gauge shall be applied to the side of the
component.
The device must withstand the stated force
without a failure of the termination.
7/10
PRODUCT SPECIFICATION
Item
SPEC. NO.
T-0619-028X
Specifications
Test conditions
Low
There must be no case deformation or
Inductors shall be subjected to temperature
temperature
change in dimensions.
-40±2℃ for 48±12 hours.
resistance
Inductance must not change more than
Measure the test items after leaving the inductors
the stated tolerance.
at room temperature and humidity for 1 to 2
hours.
Resistance to
There must be no case deformation,
solvent
change in dimensions, or obliteration
Inductors must withstand 6 minutes of alcohol or water.
of marking.
Thermal
There must be no case deformation or
Inductors shall be subjected to 10 cycles to the
shock
change in dimensions.
the following temperature cycle:
Inductance must not change more than
the stated tolerance.
1 cycle
30 min.
30 sec
+125℃
-40℃
30 min.
Measure the test items after leaving the inductors
at room temperature and humidity for 2 hours.
8/10
PRODUCT SPECIFICATION
SPEC. NO.
T-0619-028X
7.Packaging
The packaging must be done not to receive any damage during transporting and storing.
7-1 Tape dimensions
Ko
P1
P0
P
W
Bo
t
Ao
Symbol
Dimension
Tolerance
( Dimensions in mm)
Ko
t
W
P
P0
P1
Ao
Bo
8
4
4
2
2.14
3.56
1.5
0.22
±0.10
±0.10
±0.10
±0.10
±0.05
±0.05
±0.05
±0.05
7-2 Reel dimensions
D
Symbol
C
B
A
B
C
D
E
A
E
7-3 Tapping figure
Top cover tape
Carrier tape
Sprocket hole
Cavity (chip insert)
( Dimensions in mm )
T
180
60
13
14.4
8.4
9/10
PRODUCT SPECIFICATION
SPEC. NO.
T-0619-028X
7-4 Packaging Form
There shall not continuation more than two vacancies of the product.
(360 mm)
Blank
(50 pitches)
Chip
Blank
(70 pitches)
Leader.
7-5 Cover Tape Peel Strength
The force for tearing off cover tape is 0.1~0.6(N) in the arrow direction at the following conditions:
Temperature : 5 ~ 35℃
Humidity : 45 ~ 85%
Atmospheric pressure : 860 ~ 1060 hpa
160 ~ 180。
Top cover tape
Base tape
7-6 Packing Quantity
φ180 mm reel type : 2,000 pcs./reel
10/10
PRODUCT SPECIFICATION
SPEC. NO.
T-0619-028X
8. Recommended Soldering Conditions (Please use this product by reflow soldering)
8-1 Recommended Footprint
1.02
1.78
1.02
1.93
8-2 Recommended Reflow Pattern
Reflow : until two times
10 sec. Min.
255℃
217℃
Natural cooling
150sec. Max.
150℃
60sec. Min.
8-3 Iron Soldering
Use a solder iron of less than 30W when soldering ,do not allow the soldering iron tip
directly touch the Ceramic body outside of terminal electrode.
4 seconds max. at 260℃.
9. Attention in Case of Using
In case of using product ,please avoid following matters:
Splashing water or salt water
Dew condenses
Toxic gas (Hydrogen sulfide, Sulfurous acid ,Chlorine, Ammonia)
Vibrations or shocks which exceed the specified condition
Please be careful for the stress to this product by board flexure or something after the mounting.
10. Others
10-1 Operating temperature range
: Ferrite Series : -25~+85℃
Ceramic Series : -40~+125℃
10-2 Storage condition
: Temperature 20°~25℃﹐Relative Humidity 40%~60%
10-3 Recommended wire wound inductors should be used within 6 months from the time of delivery.