EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Features
•
High Efficiency (Up to 91.0%)
•
Full Power at Wide Output Current Range (Constant Power)
•
0-5V/0-10V/PWM/Timer Dimmable
•
Input Surge Protection: 6 kV line-line, 10 kV line-earth
•
All-Around Protection: OVP, SCP, OTP
•
Waterproof (IP67) and UL Dry / Damp / Wet Location
•
Class 2 & SELV Output
•
TYPE HL, for use in a Class I, Division 2 hazardous
(Classified) location
•
UL Type TL (Temperature Limited)
•
Class P, UL Listed Versions Available (See Note 6)
•
7 Years Warranty
Description
The EUG-075SxxxDT series is a 75W, constant-current, programmable LED driver that operates from 90-305
Vac input with excellent power factor. It is created for low bay, tunnel and street lights. The high efficiency of
these drivers and compact metal case enables them to run cooler, significantly improving reliability and
extending product life. To ensure trouble-free operation, protection is provided against input surge, output over
voltage, short circuit, and over temperature.
Models
Adjustable
Output
Current
Range
Full-Power
Current
Range (1)
Default
Output
Current
45-700mA
450-700mA
530 mA
70-1050mA
700-1050mA
700 mA
119-1750mA 1190-1750mA 1400 mA
140-1800mA 1400-1800mA 1400 mA
192-2800mA 1920-2800mA 2100 mA
Input
Voltage
Range(2)
90~305 Vac/
127~300 Vdc
90~305 Vac/
127~300 Vdc
90~305 Vac/
127~300 Vdc
90~305 Vac/
127~300 Vdc
90~305 Vac/
127~300 Vdc
Output
Voltage
Range
Power Factor
Max.
Typical
Output Efficiency
120Vac 220Vac
Power
(3)
Model Number
54~167Vdc 75 W
91.0%
0.99
0.96
EUG-075S070DT
36~107Vdc 75 W
90.5%
0.99
0.96
EUG-075S105DT
(4)
22 ~ 63Vdc 75 W
90.0%
0.99
0.96
EUG-075S175DT
(4)
22 ~ 54Vdc 75 W
90.0%
0.99
0.96
EUG-075S180DT
(5)
14 ~ 39Vdc 75 W
89.0%
0.99
0.96
EUG-075S280DT
(5)
Notes: (1) Output current range with constant power at 75W
(2) Certified input voltage range: UL, FCC 100-277Vac or 127-300Vdc; otherwise 100-240Vac or 127250Vdc (except KS)
(3) Measured at full load and 220Vac input (see below “General Specifications” for details).
(4) SELV Output.
(5) Class 2 & SELV Output.
(6) Standard part UL Type TL. For UL Listed Class P models add suffix -00C0.
1 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
I-V Operating Area
EUG-075S070DT
EUG-075S105DT
EUG-075S175DT
EUG-075S180DT
60
(140,54)
50
(980,54)
(1400,54)
(Ioset,75/Ioset)
(10%Ioset,75/Ioset)
10
0%
Lo
a
d
(1800,42)
%
70
ad
Lo
40
(1800,30)
30
(1800,22)
20
(180,22)
10
(Ioset,22)
Programmed Operating Area
Good Performance Area
Allowed Operating Area
0
0
350
700
1050
1400
1750
2100
Output Current (mA)
Note: 1400mA
Ioset
1800mA
EUG-075S280DT
2 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Input Specifications
Parameter
Min.
Typ.
Max.
Input Voltage
90 Vac
-
305 Vac
Input Frequency
47 Hz
-
63 Hz
-
-
0.75 MIU
UL8750; 277Vac/ 60Hz, grounding
effectively
-
-
0.70 mA
IEC60598-1; 240Vac/ 60Hz, grounding
effectively
-
-
1.05 A
Measured at full load and 100 Vac input.
-
-
0.48 A
Measured at full load and 220 Vac input.
-
-
1.3 A s
0.9
-
-
THD
-
-
20%
THD
-
-
10%
At 220-240Vac, 50-60Hz, 75%-100% Load
(56.25-75W)
Min.
Typ.
Max.
Notes
-5%Ioset
-
5%Ioset
45 mA
70 mA
119 mA
140 mA
192 mA
-
700 mA
1050 mA
1750 mA
1800 mA
2800 mA
450 mA
700 mA
1190 mA
1400 mA
1920 mA
-
700 mA
1050 mA
1750 mA
1800 mA
2800 mA
-
5%Iomax
10%Iomax
-
1%Iomax
-
Startup Overshoot Current
-
-
10%Iomax
No Load Output Voltage
EUG-075S070DT
EUG-075S105DT
EUG-075S175DT
EUG-075S180DT
EUG-075S280DT
-
-
180 V
118 V
67 V
59 V
48 V
Line Regulation
-
-
±0.5%
Load Regulation
-
-
±1.5%
Leakage Current
Input AC Current
2
Inrush Current(I t)
PF
2
Notes
127~300 Vdc
At 220Vac input, 25°C cold start,
duration=456 μs, 10%Ipk-10%Ipk. See
Inrush Current Waveform for the details.
At 100-277Vac, 50-60Hz, 70%-100% Load
(52.5-75W)
Output Specifications
Parameter
Output Current Tolerance
Output Current Setting(Ioset)
Range
EUG-075S070DT
EUG-075S105DT
EUG-075S175DT
EUG-075S180DT
EUG-075S280DT
Output Current Setting Range
with Constant Power
EUG-075S070DT
EUG-075S105DT
EUG-075S175DT
EUG-075S180DT
EUG-075S280DT
Total Output Current Ripple
(pk-pk)
Output Current Ripple at
< 200 Hz (pk-pk)
At full load condition
At full load condition. 20 MHz BW
At full load condition. Only this component
of ripple is associated with visible flicker.
At full load condition
Measured at full load
3 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Output Specifications (Continued)
Parameter
Min.
Typ.
Max.
-
-
1.0 s
-
-
0.5 s
-
0.03%/°C
-
12V Auxiliary Output Voltage
10.8 V
12 V
13.2 V
12V Auxiliary Output Source
Current
0 mA
-
20 mA
Turn-on Delay Time
Temperature Coefficient of
Ioset
Notes
Measured at 120Vac input, 70%-100%
Load
Measured at 220Vac input, 70%-100%
Load
Case temperature = 0°C ~Tc max
Return terminal is “Dim−“
Note: All specifications are typical at 25°C unless otherwise stated.
General Specifications
Parameter
Efficiency at 120 Vac input:
EUG-075S070DT
Io= 450mA
Io= 700mA
EUG-075S105DT
Io= 700mA
Io=1050mA
EUG-075S175DT
Io=1190mA
Io=1750mA
EUG-075S180DT
Io=1400mA
Io=1800mA
EUG-075S280DT
Io=1920mA
Io=2800mA
Efficiency at 220 Vac input:
EUG-075S070DT
Io= 450mA
Io= 700mA
EUG-075S105DT
Io= 700mA
Io=1050mA
EUG-075S175DT
Io=1190mA
Io=1750mA
EUG-075S180DT
Io=1400mA
Io=1800mA
EUG-075S280DT
Io=1920mA
Io=2800mA
Min.
Typ.
Max.
86.0%
87.0%
88.0%
89.0%
-
86.0%
86.5%
88.0%
88.5%
-
85.5%
86.0%
87.5%
88.0%
-
85.5%
86.0%
87.5%
88.0%
-
85.5%
84.5%
87.5%
86.5%
-
88.5%
89.0%
90.5%
91.0%
-
88.0%
88.5%
90.0%
90.5%
-
87.5%
88.0%
89.5%
90.0%
-
87.5%
88.0%
89.5%
90.0%
-
87.5%
87.0%
89.5%
89.0%
-
Notes
Measured at full load and steady-state
temperature in 25°C ambient;
(Efficiency will be about 2.0% lower if
measured immediately after startup.)
Measured at full load and steady-state
temperature in 25°C ambient;
(Efficiency will be about 2.0% lower if
measured immediately after startup.)
4 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
General Specifications (Continued)
Parameter
Min.
Typ.
Max.
89.0%
89.0%
91.0%
91.0%
-
88.0%
88.5%
90.0%
90.5%
-
88.0%
88.5%
90.0%
90.5%
-
88.0%
88.5%
90.0%
90.5%
-
88.0%
87.0%
90.0%
89.0%
-
MTBF
-
328,000
Hours
-
Lifetime
-
99,000
Hours
-
Operating Case Temperature
for Safety Tc_s
-40°C
-
+90°C
Operating Case Temperature
for Warranty Tc_w
-40°C
-
+75°C
Case temperature for 7 years warranty.
Please see Inventronics Warranty
Statement for complete details.
Operating Case Temperature
for Type TL Tc_TL
-40°C
-
+67°C
Only UL Type TL models
Storage Temperature
-40°C
-
+85°C
Humidity: 5%RH to 100%RH
Efficiency at 277 Vac input:
EUG-075S070DT
Io= 450mA
Io= 700mA
EUG-075S105DT
Io= 700mA
Io=1050mA
EUG-075S175DT
Io=1190mA
Io=1750mA
EUG-075S180DT
Io=1400mA
Io=1800mA
EUG-075S280DT
Io=1920mA
Io=2800mA
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
Net Weight
Measured at full load and steady-state
temperature in 25°C ambient;
(Efficiency will be about 2.0% lower if
measured immediately after startup.)
Measured at 220Vac input, 80%Load and
25°C ambient temperature (MIL-HDBK217F)
Measured at 220Vac input, 80%Load and
70°C case temperature; See lifetime vs. Tc
curve for the details
With mounting ear
6.97 × 2.66 × 1.44
177 × 67.5 × 36.5
5.91 × 2.66 × 1.44
150 × 67.5 × 36.5
-
790 g
Notes
-
Note: All specifications are typical at 25°C unless otherwise stated.
Dimming Specifications
Parameter
Absolute Maximum Voltage
on the Vdim (+) Pin
Source Current on Vdim
(+)Pin
Min.
Typ.
Max.
-20 V
-
20 V
200 uA
300 uA
450 uA
Notes
Vdim(+) = 0 V
5 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Dimming Specifications (Continued)
Parameter
Min.
Typ.
Max.
Notes
450 mA ≤ Ioset ≤ 700 mA
700 mA ≤ Ioset ≤ 1050 mA
1190 mA ≤ Ioset ≤ 1750 mA
1400 mA ≤ Ioset ≤ 1800 mA
1920 mA ≤ Ioset ≤ 2800 mA
45 mA ≤ Ioset ＜ 450 mA
70 mA ≤ Ioset ＜ 700 mA
119 mA ≤ Ioset ＜ 1190 mA
140 mA ≤ Ioset ＜ 1400 mA
192 mA ≤ Ioset ＜ 1920 mA
EUG-075S070DT
EUG-075S105DT
EUG-075S175DT
EUG-075S180DT
EUG-075S280DT
10%Ioset
-
Ioset
EUG-075S070DT
EUG-075S105DT
EUG-075S175DT
EUG-075S180DT
EUG-075S280DT
45 mA
70 mA
119 mA
140 mA
192 mA
-
Ioset
Recommended Dimming
Range for 0-5V
0V
-
5V
Dimming mode set to 0-5V in PC interface.
Recommended Dimming
Range for 0-10V
0V
-
10 V
Default 0-10V dimming mode with positive
logic.
PWM_in High Level
3V
-
10 V
PWM_in Low Level
-0.3 V
-
0.6 V
PWM_in Frequency Range
200 Hz
-
2 KHz
1%
-
99%
Dimming
Output
Range
PWM_in Duty Cycle
Dimming mode set to PWM in PC interface.
Safety &EMC Compliance
Safety Category
UL/CUL
Standard
UL8750, UL1310, CAN/CSA-C22.2 No. 250.13, CAN/CSA-C22.2 No. 223-M91
CE
EN 61347-1, EN61347-2-13
KS
KS C 7655
EMI Standards
(1)
EN 55015
Notes
Conducted emission Test &Radiated emission Test
EN 61000-3-2
Harmonic current emissions
EN 61000-3-3
Voltage fluctuations & flicker
ANSI C63.4 Class B
(1)
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: [1] this device may not cause harmful interference, and [2] this
device must accept any interference received, including interference that may cause
undesired Operation.
EMS Standards
Notes
EN 61000-4-2
Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge
EN 61000-4-3
Radio-Frequency Electromagnetic Field Susceptibility Test-RS
EN 61000-4-4
Electrical Fast Transient / Burst-EFT
EN 61000-4-5
Surge Immunity Test: AC Power Line: line to line 6 kV, line to earth 10 kV
(2)
6 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Safety &EMC Compliance (Continued)
EMS Standards
Notes
EN 61000-4-6
Conducted Radio Frequency Disturbances Test-CS
EN 61000-4-8
Power Frequency Magnetic Field Test
EN 61000-4-11
Voltage Dips
EN 61547
Electromagnetic Immunity Requirements Applies To Lighting Equipment
Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that
contains it depends also on the other devices connected to the driver and on the fixture itself.
(2) To perform electric strength (hi-pot) testing, the “GDT ground disconnect” (nut and metal lock
sheet) on the driver end-cap should be removed temporarily to prevent the internal gas discharge
tube from conducting (as allowed by IEC 60598-1 Clause 10.2). After testing is completed, these
items must be reinstalled to restore line-to-earth surge protection and secure the end cap.
Lifetime vs. Case Temperature
Inrush Current Waveform
7 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Efficiency vs. Load
EUG-075S070DT(Io=450mA)
EUG-075S070DT(Io=700mA)
EUG-075S105DT(Io=700mA)
EUG-075S105DT(Io=1050mA)
EUG-075S175DT(Io=1190mA)
EUG-075S175DT(Io=1750mA)
8 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
EUG-075S180DT(Io=1400mA)
EUG-075S180DT(Io=1800mA)
EUG-075S280DT(Io=1920mA)
EUG-075S280DT(Io=2800mA)
Power Factor
9 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Total Harmonic Distortion
Protection Functions
Parameter
Notes
Over Temperature Protection
Decreases output current, returning to normal after over temperature is removed.
Short Circuit Protection
Auto Recovery. No damage will occur when any output is short circuited. The output
shall return to normal when the fault condition is removed.
Over Voltage Protection
Limits output voltage at no load and in case the normal voltage limit fails.
Dimming
0-5V Dimming
The recommended implementation of the dimming control is provided below.
Implementation 1: Positive logic
10 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Implementation 2: Negative logic
Notes:
1. The dimmer can also be replaced by an active 0-5V voltage source signal or passive components like
resistors and zener.
2. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
3. If 0-5V dimming is not used, Dim + should be open.
4. When 0-5V negative logic dimming mode and Dim+ is open, the driver will output maximum current.
0-10V Dimming
The recommended implementation of the dimming control is provided below.
Implementation 3: Positive logic
Implementation 4: Negative logic
11 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Notes:
1. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like
resistors and zener.
2. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
3. If 0-10V dimming is not used, Dim + should be open.
4. When 0-10V negative logic dimming mode and Dim+ is open, the driver will output minimum current.
PWM Dimming
The recommended implementation of the dimming control is provided below.
Implementation 5: Positive logic
Implementation 6: Negative logic
Notes:
1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
2. If PWM dimming is not used, Dim + should be open.
3. When PWM negative logic dimming mode and Dim+ is open, the driver will output minimum current.
12 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Time Dimming
Set the timing curve by pulling the sliders.
Programming Connection Diagram
Note: The driver does not need to be powered on during the programming process.
13 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Please refer to PRG-MUL2 (Programmer) datasheet for details.
Mechanical Outline
INPUT (UL SJTW 3*18AWG
7.8)
AC/L (BLACK)
AC/N (WHITE)
GND (GREEN)
Dimming Wire(UL21996 3*22AWG
Tc
5.0)
V+ (RED)
V- (BLUE)
OUTPUT (UL SJTW 2*18AWG
GRAY
PURPLE
BLACK/WHITE
7.3)
PROJ:
Unspecified tolerance:±1
RoHS Compliance
Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other
hazardous substances from electronic products.
14 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
EUG-075SxxxDT
75W Programmable IP67 Driver
Rev. E
Revision History
Description of Change
Change
Date
Rev.
2015-12-28
A
2016-04-12
2017-03-28
2017-07-26
2017-10-25
Item
B
C
D
E
From
To
Datasheets Release
/
/
Features
/
Updated
General Specifications
Operating Case Temperature for
Type TL Tc_TL
Added
General Specifications
Net Weight
Updated
General Specifications
With mounting ear
Added
Safety &EMC Compliance
/
Updated
Mechanical Outline
/
Updated
EUG-075S180DT
/
Added
I-V Operation Area
EUG-075S180DT
Added
Output Specifications
Output Current Setting(Ioset) Range Updated
Output Specifications
Output Current Setting Range with
Constant Power
Updated
Output Specifications
No Load Output Voltage
Updated
General Specifications
Efficiency at 120 Vac input
Updated
General Specifications
Efficiency at 220 Vac input
Updated
General Specifications
Efficiency at 277 Vac input
Updated
Dimming Specifications
Dimming Output Range
Updated
Safety & EMC Compliance
/
Updated
Efficiency vs. Load
EUG-075S180DT
Added
Mechanical Outline
/
Updated
Input Specifications
PF/THD
Updated
Features
Class P, UL Listed Versions
Available (See Note 6)
Added
Features
7 Years Warranty
Added
Models
(6) Standard part UL Type TL. For
UL Listed Class P models add suffix Added
-00C0.
Operating Case Temperature for
/
Warranty Tc_w
Operating Case Temperature for
Only UL Type TL models
Type TL Tc_TL
Updated
Added
15 / 15
Specifications are subject to changes without notice.
www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com
工商网监
湘ICP备2023018690号
