3.GL.2C100M0612T8899

益阳市中钰科技电子有限公司 YIYANG HOWLET TECHNOLOGY ELECTRONLC CO.,LTD 产品承认书 SPECIFICATION FOR APPROVAL 客户名称（CUSTOMER）： 立创 产品名称（PROD. NAME）： 环保铝电解电容器 规格型号（SPEC.）： 日 期（DATE）： CD11G L 系列/6000H/环保 2022/02/28 客户接收(CUSTOMER)： 接收人(RECEIVER)： 检验人(TESTER)： 审核(APPROVED)： 供应商(VENDOR)： 拟制(DRAWN)： 审核(CHECK)： 批准(APPROVED)： 胡且力 公司：益阳市中钰科技电子有限公司 地址：湖南省益阳市赫山区龙岭工业园 电话：0737-4688883 传真：0737-4688585 邮件：Sales06@zycap.com Http://www.zycap.com 付 欣 Issued Date 2022-03-08 Status Released File Description Approval Sheet-CD11GL 变 更 履 历 表 顾客物料名称 中钰物料名称 铝电解电容器 顾客型号规格 中钰型号规格 CD11GL 版 变更原因 项 目 1 日 期 本 File No/Rev CRS2006-G/01 2022/02/28 日 期 2022/02/28 描 述 第一次承认 2 3 4 5 6 7 8 修 改 审 核 批 准 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 001 Issued Date 2022-03-08 Status Released File Description Approval Sheet-CD11GL File No/Rev CRS2006-G/01 承 认 规 格 序号 客户料号 中钰型号规格 中钰料号 尺寸 备注 01 C2975996 1uF ±20% 400V 3.GL.2G1R0M0609T8899 6.3×9mm HOWLET（中钰）） C2975995 33uF ±20% 250V 3.GL.2E330M1320T8899 13×20mm HOWLET（中钰）） C2975994 4.7uF ±20% 250V 3.GL.2E4R7M0811TN199 8×11 HOWLET（中钰）） C2975993 2.2uF ±20% 250V 3.GL.2E2R2M0612TN199 6.3×12 HOWLET（中钰）） C2975992 1uF ±20% 250V 3.GL.2E1R0M0610TQC00 6.3×10 HOWLET（中钰）） C2975998 2.2uF ±20% 400V 3.GL.2G2R2M0609TN1G3 6.3×12 HOWLET（中钰）） C2975990 22uF ±20% 160V 3.GL.2C220M0812T8899 8×12 HOWLET（中钰）） C2975989 10uF ±20% 160V 3.GL.2C100M0612T8899 6.3×12 HOWLET（中钰）） C2976006 6.8uF ±20% 400V 3.GL.2G6R8M1013T8899 10×13 HOWLET（中钰）） C2976005 6.8uF ±20% 400V 3.GL.2G6R8M0814TQQ03 8×14 HOWLET（中钰）） C2976004 6.8uF ±20% 400V 3.GL.2G6R8M0812TQC00 8×12 HOWLET（中钰）） C2975997 2.2uF ±20% 400V 3.GL.2G2R2M0609TN199 6.3×9 HOWLET（中钰）） C2976002 4.7uF ±20% 400V 3.GL.2G4R7M0812TF499 8×12 HOWLET（中钰）） C2976001 3.3uF ±20% 400V 3.GL.2G3R3M0816CT399 8×16 HOWLET（中钰）） 02 03 04 05 06 07 08 09 10 11 12 13 14 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 002 Issued Date 2022-03-08 Status Released File Description Approval Sheet-CD11GL File No/Rev CRS2006-G/01 承 认 规 格 序号 客户料号 中钰型号规格 中钰料号 尺寸 C2976000 备注 3.3uF ±20% 400V 3.GL.2G3R3M0812TQQ03 8×12 HOWLET（中钰）） C2975999 3.3uF ±20% 400V 3.GL.2G3R3M0812TQC00 8×12 HOWLET（中钰）） C2976010 15uF ±20% 400V 3.GL.2G150M1020CT399 10×20 HOWLET（中钰）） C2975991 68uF ±20% 200V 3.GL.2D680M1025TC00 10×25 HOWLET（中钰）） C2976003 5.6uF ±20% 400V 3.GL.2W5R6M8B14TP699 8×14 HOWLET（中钰）） C2976009 10uF ±20% 400V 3.GL.2G100M1016CT399 10×16 HOWLET（中钰）） C2976008 8.2uF ±20% 400V 3.GL.2G8R2M1013T8899 10×13 HOWLET（中钰）） C2976007 6.8uF ±20% 400V 3.GL.2G6R8M1013CT399 10×13 HOWLET（中钰）） C2976012 22uF ±20% 400V 3.GL.2G220M1220CT399 12×20 HOWLET（中钰）） C2976011 22uF ±20% 400V 3.GL.2G220M1220TN199 12×20 HOWLET（中钰）） C2976013 10uF ±20% 450V 3.GL.2W100M1016TN199 10×16 HOWLET（中钰）） × HOWLET（中钰）） 15 16 17 18 19 20 21 22 23 24 25 26 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 003 Issued Date 2022-03-08 Status Released File Ddscription Customer File No/Rev Approval Sheet-CD11GL SERIES CRS2006-G/01 CD11GL 2022/02/28 DATE d±0.05 D+0.5（Max) F±0.5 L+α TABLE-1 Customer No. No. 1 2 Part Howlet Part No. C2975996 3.GL.2G1R0M0609T8899 C2975995 3.GL.2E330M1320T8899 Issued-date:2022-03-08 Tolerance Rated Surge Operating tanδ Capacitance on Rated Voltage Voltage Temp. Range (120Hz) (μF) Capacitanc (Max) (Vdc) (Vdc) (℃) e (%) Leakage Current (μA) (2min.) Max Ripple Current (mArms) at105℃ 100kHz 59 6000 535 6000 1.0 ±20 400 450 105 0.10 12 33 ±20 250 300 105 0.10 247.5 Name File No Endurance at 105℃ (Hours) Dimensions (mm) ΦD L α d F 6.3 9 2 0.5 2.6 13 20 2 0.6 5.3 Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL Appearance Drawing F1 No. / 004 Issued Date 2022-03-08 No. 3 4 5 6 7 8 9 10 11 12 13 Customer Part No. C2975994 Status Howlet Part No. Released File Ddscription File No/Rev Approval Sheet-CD11GL Tolerance Rated Surge Operating tanδ Capacitance on Rated Voltage Voltage Temp. Range (120Hz) (μF) Capacitanc (Max) (Vdc) (Vdc) (℃) e (%) Leakage Current (μA) (2min.) CRS2006-G/01 Max Ripple Current (mArms) at105℃ 100kHz Endurance at 105℃ (Hours) 3.GL.2E2R2M0612TN199 C2975992 3.GL.2E1R0M0610TQC00 C2975998 3.GL.2G2R2M0609TN1G3 C2975990 3.GL.2C220M0812T8899 C2975989 3.GL.2C100M0612T8899 C2976006 3.GL.2G6R8M1013T8899 C2976005 3.GL.2G6R8M0814TQQ03 C2976004 3.GL.2G6R8M0812TQC00 C2975997 3.GL.2G2R2M0609TN199 C2976002 3.GL.2G4R7M0812TF499 Issued-date:2022-03-08 ΦD L α d F 4.7 ±20 250 300 105 0.10 32.25 102 6000 2.2 ±20 250 300 105 0.10 16.5 75 6000 1 ±20 250 300 105 0.10 12.5 46 6000 2.2 ±20 400 450 105 0.10 9.4 78 6000 22 ±20 160 200 105 0.10 105.6 320 6000 10 ±20 160 200 105 0.10 48 180 6000 6.8 ±20 400 450 105 0.10 81.6 145 6000 6.8 ±20 400 450 105 0.10 81.6 128 6000 8 14 2 0.5 3.5 6.8 ±20 400 450 105 0.10 81.6 128 6000 8 12 2 0.5 3.5 2.2 ±20 400 450 105 0.10 9.6 72 6000 6.3 9 2 0.5 2.6 4.7 ±20 400 450 105 0.10 56.4 104 6000 8 12 2 0.5 3.5 3.GL.2E4R7M0811TN199 C2975993 Dimensions (mm) Name File No 8 Appearance Drawing F1 No. 12 2 0.5 3.5 / 6.3 12 2 0.5 2.6 6.3 10 2 0.5 2.6 6.3 12 2 0.5 2.6 8 12 2 0.5 3.5 6.3 12 2 0.5 2.6 10 2 0.6 5.3 Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 13 005 Issued Date 2022-03-08 No. 14 15 16 17 18 19 20 21 22 23 24 25 Customer Part No. C2976001 Status Howlet Part No. 3.GL.2G3R3M0816CT399 C2976000 3.GL.2G3R3M0812TQQ03 C2975999 3.GL.2G3R3M0812TQC00 C2976010 3.GL.2G150M1020CT399 C2975991 3.GL.2D680M1025TC00 C2976003 3.GL.2W5R6M8B14TP699 C2976009 3.GL.2G100M1016CT399 C2976008 3.GL.2G8R2M1013T8899 C2976007 3.GL.2G6R8M1013CT399 C2976012 3.GL.2G220M1220CT399 C2976011 3.GL.2G220M1220TN199 C2976013 3.GL.2W100M1016TN199 Issued-date:2022-03-08 Released File Ddscription File No/Rev Approval Sheet-CD11GL Tolerance Rated Surge Operating tanδ Capacitance on Rated Voltage Voltage Temp. Range (120Hz) (μF) Capacitanc (Max) (Vdc) (Vdc) (℃) e (%) Leakage Current (μA) (2min.) CRS2006-G/01 Max Ripple Current (mArms) at105℃ 100kHz Endurance at 105℃ (Hours) 3.3 ±20 400 450 105 0.10 39.6 91 6000 3.3 ±20 400 450 105 0.10 39.6 91 6000 3.3 ±20 400 450 105 0.10 39.6 91 6000 15 ±20 400 450 105 0.10 180 274 6000 68 ±20 200 250 105 0.10 408 580 6000 5.6 ±20 400 450 105 0.10 67.2 125 6000 Dimensions (mm) ΦD L α d F 8 16 2 0.5 3.5 / 8 12 2 0.5 3.5 8 12 2 0.5 3.5 10 20 2 0.6 5.3 10 25 2 0.6 5.3 8 14 2 0.5 3.5 10 16 2 0.6 5.3 10 ±20 400 450 105 0.10 120 226 6000 8.2 ±20 400 450 105 0.10 98.4 208 6000 10 13 2 0.6 5.3 6.8 ±20 400 450 105 0.10 81.6 145 6000 10 13 2 0.6 5.3 22 ±20 400 450 105 0.10 264 350 6000 12 20 2 0.6 5.3 22 ±20 400 450 105 0.10 264 350 6000 12 20 2 0.6 5.3 10 ±20 450 500 105 0.10 135 208 6000 10 16 2 0.6 5.3 Name File No Appearance Drawing F1 No. Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 006 Issued Date Status File Ddscription File No/Rev 2022-03-08 Released Approval Sheet-CD11GL CRS2006-G/01 1、 概述 SCOPE 本承认书规定了 CD11GL 系列径向引线引出铝电解电容器的技术规范。 This specification covers“CD11GL series”radial type aluminum electrolytic capacitors. 2、参考标准 APPLI CABLE SPECIFICATION 本承认书参考 GB/T2693 和 GB/T18504 制定。 This approval sheet consulted the institute of GB/T2693 and GB/T18504 3、工作温度范围 OPERATING TEMPERATURE RANGE 工作温度范围是电容器在施加额定工作电压条件下，可以长期可靠工作的环境温度范围。 -40~+105℃(140~450V) Operating temperature range is the range of ambieng temperature at which the capacitor can be operated continuously at rated voltage. -40~+105℃(140~450V) 4、测试环境 ATMOSPHERIC COND I T I ON OF MEASUREMENTS： 如果没有其他规定，标准的测试、检验环境条件如下所示： 环境温度：15 至 35℃ 相对湿度：45 至 75% 大气压力：86kpa 至 106kpa 如果对测试结果有异议，可以在以下条件测试： 环境温度：25±2℃ 相对湿度：60 至 70% 大气压力：86kpa 至 106kpa Unless otherwise specitied,the standard range of atmospheric conditions for making Measurements and tests are as follows Ambient temperature :15 to 35℃ Relative humidity : 45 to 75% Air pressure : 86kpa to 106kpa If there may be doubt on the results, measurements shall be made within the following limits. Ambient temperature :25 ±2℃ Relative humidity : 60 to 70% Air pressure : 86kpa to 106kpa Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 1 Issued Date Status File Ddscription 2022-03-08 Released Approval Sheet-CD11GL 5.1 电气特性 ELECTRICAL CHARACTERISTICS 序号 NO 5.1.1 5.1.2 项目 Item 测试方法 Test method 性能 Performance DC160~450v 额定工作电压 Rated voltage 电容量 Capacitance File No/Rev CRS2006-G/01 测试频率:120HZ±10% 测试电路:串联等效 测试电压:0.5Vrms 以下 Measuring frequency : 120HZ±10% Measuring circuit: Series equivalent circuit Measuring voltage: 0.5Vrms or less +1.5 to 2.0 VDC 1~100μF 容量偏差: CD11GL:-20%+20% tgδ≤0.10 Capacitance tolerance: CD11GL:-20%+20% 5.1.3 损耗角角正切值 Dissipation Factor 测试条件与 5.1.2 电容量测试相同 Testing condition are the sane as 5.1.2 for capacitance 5.1.4 漏电流 Leakage current 在电容器两端施加额定工作电压后,并串联 1000±100 电压(160~450V) Ω电阻,在施加电压 1 分钟后,测量漏电流. CD11GL:1 分钟后 测试电路如下图： IC≤0.1CV+40 (CV≤1000) The rated voltage shall be applied across the capacitor IC≤0.04CV+100 and (CV≥1000) Its protectivd resistor which shall be 1000±100Ω.The leakage current shall then be measured after an IC: 漏电流(μA) electrification period of 1 min.. C:容量(μF) V:额定工作电压(V) μA μA Voltage(160~450V) CD11GL:Not more than IC ≤0.1CV+40 μA (CV≤1000) IC≤0.04CV+100 μA (CV≥1000) IC:Leakage current(μA) C:Capacitance(μF) V:Rated voltage(V) Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 2 Issued Date 2022-03-08 5.1.5 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 阶段 2： 温度特性 Temperature 阶段 温度 时间 Characteristi 1 -- 比，不大于表 1 要求。 c 2 20±2℃ +0 -25-3℃ +3 105-0℃ 2h 阶段 3： 3 2h 阶段 1:测量容量和阻抗 (íZí20℃ 120HZ±20%) 阶段 2:电容器恒温贮存 2 小时,在热平衡状态测阻抗 (íZí -25℃ 120HZ±20%) 阶段 3:电容器恒温贮存 2 小时,在热平衡状态测电容量 Step1:Capacitance and impedance shall be measured. (íZí 20℃ 120HZ±20%) Step2:After the capacitor being stored for 2 hours,impedance shall be made at thermal stability. ( Z -25℃ 120HZ±20%) 阻抗值与阶段 1 阻抗值相 容量变化应在初值的± 20%范围内 Step2:Impedance ratio Shall be not more Value give bable-1 Step3: Variation of capacitance Within ±20% of the value at Step 1. Step3：After the capacitor being stored for 2 hours,capacitance shall be measured. The meaaurement shall be made at thermal stability 5.1.6 耐浪涌电压 施加表 1 所列浪涌电压，充电 30±5 秒，放电 5.5±0.5 分钟作为一个周期, Surge 共进行 1000 次. 测试温度:15℃-35℃ 然后在标准大气条件下放置达到热稳定,测试各参数 Application of DC surge Voltage stated at tabld-1,1000 times of charging for 30±5 sec ,with a period of 6±0.5 min.. Test temperature: 15℃-35℃ And the capacitor shall be stored under standard atmospheric conditions to obtain thermal stability, after which measurements shall be made. Issued-date:2022-03-08 Name File No 容量：不低于试验前的 80% 损耗角正切值不大于 200% 的表规定值。 漏电流：达到 5.1.4 要求 Capacitance: Not less than 80% of the value before test. Dissipation factor: Not more 200% of the specified value in table-1 Leakage current: To satisfy No.5.1.4 Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 3 Issued Date Status File Ddscription 2022-03-08 Released Approval Sheet-CD11GL 5.2 机械特性 MECHANICAL PERFORMANCE File No/Rev CRS2006-G/01 序号 项目 测试方法 特性 NO Item Test method Performance 5.2.1 端子强度 端子抗拉强度: 测量电容器应无接触不良、开 TERMINAL 沿电容器端子引线方向施加固定重力*1N 路或短路，无可见机械损伤 STRENGTH 10 秒钟. 引线直径Φ 0.5 拉力 N 5.0 0.6 0.8 10 1.0 20 端子抗弯强度: When 在电容器引线施加固定重力*2N,然后,将电容体弯折 90°后回到原位。 mdawured ,there shall bd no 上述过程在 5 秒内完成。 imtermittent contacts,or open 引线直径Φ 0.5 拉力 N 5.0 0.6 0.8 10 the capacitance 1.0 or short-circuiting. 20 There Tensile strength of termination: shall be no is such mechanical damgement. A static load of* IN shall be applied to the terminal in the axial direction and acting in a direction away from the body for 10 sec. Bending strength of termination: Hang the specified dead weight of*2N,then bent the body through 90° with The same speed ,again return to the original position Carry out this operation im abaut 5 sec. 5.2.2 振动试验 依据 IEC60068-2-6 试验。 测量电容量应无接触不良开路 Resistance to 在 3 个互相垂直的方向分别施加 2 小时振动，共 6 小时 或短路,无可见机械损伤。 Vibration To comply with IEC60068-2-6 When Direction and duration of vibration: measured there shall be no 3 orthogonal directions mutually each for 2h,Total 6h. intermittent contacts or open the capacitance is or short circuiting There shall be no such mechanical damage. 5.2.3 可焊性 依据 IEC60068-2-2 进行试验 浸入焊锡的引线表面积约 3/4 Solder ability 焊锡温度：230±5℃ 以上应附着新锡 浸入时间：2±0.5 秒 To comply with IEC60068-2-2 Temperature or solder:235±5℃ At least 3/4f circumferential Dipping time: 2±0.5sec surface of the dipping portion This specification shall be met after the capacitors are stored under of standard Termination shall be covered Atmospheric conditions for 6 months. with new solder. Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 4 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 5.3 特性测试 CHARACTERISTICS EXPERIMENT 序号 项目 试验方法 特性 NO Item Experiment method Performance 5.3.1 耐焊接热 : 焊槽法 容量变化:在初始值±10%范围内损 焊锡温度: 260±5℃ 耗角角正切值： 满足表 1 要求漏电流： 浸入时间: 10±1 秒 满足 5.1.4 要求 1.6MM 外观:无异状 : 电路板 Solder bath method Variation of capacitance: Solder temperature: 260±5℃ Within ± 10% of the value before Immersion time test. : 10±1sec Printed wiring board: 1.6MM Dissipation factor: To satisfy table 1. Leakage current: To satisfy No.5.1.4 Appearance: No remarkable abnormality . 5.3.2 依据 IEC60068-2-3 进行试验 容量变化：在初始值±15%范围内 to 试验温度：40±2℃ 损耗角正切值：满足表 1 要求， heat 试验时间：240±8h 漏电流：满足 5.1.4 要求 相对湿度：90~95% 外观:无异状 试验后，电容器在标准大气条件下 1~2 小时，然后测试参数 Variation of capacitance: To comply with IEC60068-2-3 Within ± 15% of the value before Test temperature: 40±2℃ test. Test time Dissipation factor: 稳态湿热 Resistance damp (steady state) : 240±8h Relative humidity: 90~95% To satisfy Table 1. After completion of test,the capacitor shall be subjected to Leakage current: standard atmospheric conditions for l to 2 hours,after which To satisfy No.5.1.4 measurements shall be made. Appearance: No remarkable abnormality. 5.3.3 高温负荷试验 1、试验温度：105±2℃施加额定电压和额定纹波电流 容量变化：在初始值±20%范围内 LIFE TEST Application of the rated voltage and rated ripple current 损耗角正切值：满足表 1 所列规定值 temperature:105±2℃ 的 200% +72 试验时间：CD11GL：6000-0 h Test temperature: 105±2℃ +72 Test time:CD11GL : 6000-0 h 漏电流：满足 5.1.4 要求 外观:无异状 Variation of capacitance: Within ± 20% of the value before test. Dissipation factor: Not more than 200% of the specified value in Table 1. Leakage current: To satisfy No.5.1.4 Appearance: No remarkable abnormality. Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 5 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 序号 项目 测试方法 特性 NO Item Test method Performance +48 1、在 105±2℃环境下无负荷贮存 1000-0 h，至少恢复 16 小时后。 容量变化：初始值±20%范围 内。 损耗角正切值：不超过表 1 所 列规定值的 200% 漏电流：不超过 5.1.4 所规定 值的 200% 外观:无异状 Variation of capacitance: Within ± 30% of the value before test. Dissipation factor: Not more than 200% of the specified value in Table 1. Leakage current: Not more than 200% of the specified value in 5.1.4 5.3.4 高温贮存试验 SHELF 5.3.5 LIFE TEST The capacitors are then stored with no voltage at a +48 temperature of 105 ± 2 ℃ for 1000-0 h and then resumed 16 hours. 防爆试验 在电容器两极施加反向工作电压，其中通过的电流应不大 上述过程中应无引线,铝箔等 SAFETY VENT 于 1A，在测试时防爆装置应能在 30 分钟内动作。 散射,无火花产生。 D．C．Application test The vent device is actuated The capacitor shall be subjected to a reverse D.C, voltage under the test conditions, equal to the rated D.C. voltage. thereby The current flowing through the capacitor shall be limited terminals,metal to 1A. the capacitor from scattering preventing pieces,etc,of due to burst, the case form separating from the seal packing,or the capacitor from producimg flame. 表 1、（TABLOEI） 额定工作电压 损耗角正切值 Rated voltage(V) Dissipation factor*3 160 0.10 200 阻抗比 íZí-25℃/íZí20℃ 3 0.10 3 250 0.10 3 350 0.10 6 400 0.10 6 450 0.12 6 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version STANDARD MANUAL 00 Page 6 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 6、标记 MARKING 6.1 在电容器体上应注明如下内容: (1) 生产厂商商标 (2) 工作电压 (3) 型号规格 (4) 负极标志 (5) 额定温度 The following items shall be marked imdelibly on the capacitor. (1) Manufacture’ s name or trade mark. (2) Rated voltage (3) Type and specification (4) Polarity of the terminals (5) R acted temperature 6.2 标记颜色 套管颜色: CD11GL 中钰紫色 标记颜色:黑色 Marking color Sleeve color: CD11GL:HOWLET PURPLE Marking color: Black Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 7 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 7. 内部结构及材料表 Frame and material 7.1 构造图 Frame drawing 7.2 芯包分解图 Element drawing 7.3 材料表 Material Table NO 构成部件 材质 NO 构成部件 材质 1 铝壳 铝 6 负极箔 铝 2 橡胶塞 丁基胶 7 粘合剂 聚乙烯醇/电子胶带 3 引出线 铝+CP 线 8 电解液 有机溶液 4 正极箔 铝 9 套管 PET 5 电解纸 纤维 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 8 Issued Date Status File Ddscription 2022-03-08 Released Approval Sheet-CD11GL 8、尺寸表、允许纹波电流 DIMENSIONS AND RIPPLE CURRENT Case Size 外形尺寸：D（0~+1）×L(0~+2)(mm) File No/Rev CRS2006-G/01 Ripple Current 纹波电流：（mA，105℃/100KHZ） （见前面 003-006 页） 9、纹波电流频率因子 RIPPLE CURRENT FREQUENCY COEFFICIENT WV（V） 120HZ 1KHZ 10KHZ 100KHZ 160-450 0.50 0.80 0.90 1.00 10 、加工型式 Forming Lead Type PIN Code : B ΦD=4~8 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 9 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 DIMENSIONS(mm) CASE SIZE Symbol Items 5x11 6.3x11 8x11 8x16 10x13 5x12 6.3x12 8x12 8x20 10x16 Tolerance 10x20 X Pin Code B B B B B Φd 0.5 0.5 0.4/0.5 0.6 0.6 ±0.05 Pitch of body P 12.7 12.7 12.7 12.7 12.7 ±1.0 Feed hole pitch P0 12.7 12.7 12.7 12.7 12.7 ±0.2 Hole center to lead distance P1 5.1 4.6 4.6 3.85 ±0.7 Feed hole center to body P2 6.35 6.35 6.35 6.35 ±1.0 2.5 3.5 3.5 5.0 ±0.5 Lead wire diameter 5.1 5.35 6.35 centerdistance Lead to leaddistance F 2.5 2.0 Height of body from tape H 18.5 18.5 18.5 18.5 18.5 ±0.75 Base tape width W 18.0 18.0 18.0 18.0 18.0 ±0.5 Adhesive tape width W0 11.0 11.0 11.0 11.0 11.0 min Hole position W1 9.0 9.0 9.0 9.0 9.0 +0.75-0.5 Hole down tape position W2 3.0 3.0 3.0 3.0 3.0 max center Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 10 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 11、其它说明 11．1 铝电解电容器使用注意事项：IMPORTANT INFORMATION OM THE APPLICATION OF ALUMINUM ELECTROLYTIC CAPACITORS （1）.直流铝电解电容器应按正确的极性使用 DC electrolytic capacitors are polarized 当直流铝电解电容器按反极性接入电路时，电容器会导致电子线路短路，由此产生的电流会引致电容器损坏。若电路中有可 能在负引线施加正极电压，请选正极性产品。 When reverse voltage is applied on DC electrolytic capacitor, the capacitor will become short circuited please use non polarized capccitors in the circuit are damage due to abnormal current flows through the capacitors since the circuit where the positive voltage may be applied to the cathode terminal. （2）.在额定工作电压以下作用 Use capacitor within rated voltage 当电容器上所施加电压高于额定工作电压时，电容器的漏电流将上升，其电气特性将在短时内劣化直至损坏。请注意电压蜂 值勿超出额定工作电压。 When capacitor is rsed at higher voltage than the rated voltage,leakage current increases ,characteristics drastically deteriorate and damage in a short period may occur as a result .please take extra caution that the peak voltage should not exceed the rated voltage. （3）.作快速充放电使用 Charge and discharge application 当常规电容器被用作快速充电用途。其使用寿命可能会因为容量下降，温度急剧上升等而缩减。 When aluminum electrolytic capacitors for general purpose are employed in rapid charge and discharge application,its life expectancy may be shortened by capacitance decrdase,heat rise ,etc. （4）.电容器贮存 Store the capacitor 当铝电解电容器作了长期贮存后,其漏电流通常升高.贮存温度愈高,漏电流上升愈快.因此应注意贮存环境的选择,在电容器上施 加电压后,漏电流值将不断下降,在铝电解电容器的漏电流值上升对电路有不良影响的,请在使用前充电处理. I creased leakage current is common in aluminum capacitors which have been stored flr long period of time .The higher the storage temperature,the higher the leakage current increase therefore please take precautions concerning the storage location. The leakage current causes problems in the circuit ,apply voltage (aging) before using . (5).施加纹波电流应小于额定值 Ripple current applied to capacitor should not exceed the rated value. 施加纹波电流超过额定值后,会导致电容器体过热,容量下降,寿命缩短.所施加纹波电压的峰值应小于额定工作电压. Excessive heat will reduce capacitance and result in shortened life of capacitor if ripple currents exceeding the specified rated value are applied .the peak value of the ripple voltage should be less than the rated voltage. Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 11 Issued Date 2022-03-08 （6）、引出线强度 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 Lead stress 当拉力施加到电容器引出线，该拉力将作用于电容器内部，这将导致电容器内部短路、开路或漏电流上升。在电容器焊装到 电路板，请勿强烈摇动电容器。 When a strong flrce is applied to the lead wires or terminals.stress is put on the internal connections.This may result in short circuit,open circuit or increased leakage current .It is not advisable to bend or handle a capacitor after it has been soldered to the PC board. （7）、焊接过程耐热性 Heat resistance at the soldering process 铝电解电容器装至电路板进行浸焊或波焊时，其塑料套管可能因焊接时间过长、温度过高而发生破裂或二次收缩。 In the dip soldering process of PC board with aluminum electrolytic capacitors mounted, secondary shrinkage or crack of PVC sleeve may be observed when solder temperature is too high or dipping time is too long. （8）、电路板的安装孔孔距及安装位置 Hole pitch and position of PC board. 电路板的安装孔的设计应与产品说明书的引线脚距相一致，如果将电容器强行插入孔距不配套的电路板，那么会有应力作用 于引出线，这将导致短路或漏电流上升。 A PC board must be designed so its hole pitch coincides with the lead pitch(lead spacing) of the capacitor specified catalog or specifications .When a capacitor is forcibly inserted into an unmatched hole pitch ,a stress is by the put on the leads This could result In a short circuit or increased leakage current. 11.2 本产品无铅、无污染 This produst is lead free and environmental friendly 本产品（包括所有构件）完全符合欧盟 ROHS 最新标准要求，即 10 种有害物质的最大含量均不超过如下要求： This product is according to the standard of ROHS ,it means the max capacitance of ten harmful material not over the following repuest: Cd (镉) -100PPM Cr4 (6 价铬) -1000PPM PB (铅) -1000PPM PBBs (多溴联苯) -1000PPM DBP(邻苯二甲酸二丁酯）-1000PPM Name File No PBDEs (多溴联苯醚) -1000PPM BBP（邻苯二甲酸丁苄酯）-1000PPM DEHP（（邻苯二甲酸二（2-乙基己基）酯）-1000PPM Issued-date:2022-03-08 Hg (汞) -1000PPM CD11GL DIBP（邻苯二甲酸二异丁酯）-1000PPM Approval Sheet –CD11GL Version 00 Page STANDARD MANUAL 12 Issued Date 2022-03-08 Status Released File Ddscription Approval Sheet-CD11GL File No/Rev CRS2006-G/01 电容器生产流程: IQC 正极箔 负极箔 切割 引线 IQC 钉卷 蕊包检查 铝壳 橡胶塞 浸渍 装配 套管 套管 老练 电解纸 IQC 分选 QC 外观检查 QC QC 包装 QA 检查 QC 入库 QC 出货 QC IQC：进料质量检验 QC：工序质量检验 QA：出厂质量检查 Issued-date:2022-03-08 Name File No Approval Sheet –CD11GL CD11GL Version 00 Page STANDARD MANUAL 13