TB6S

TB2S THRU TB10S Voltage Range - 40 to 200 V olts Current - 1.0 Ampere SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIERS Features TBS  Ideal for printed circuit board  Reliable low cost construction utilizing molded plastic technique  High temperature soldering guaranteed: 260°/10 seconds at 5 lbs., (2.3kg) tension  Small size, simple installation  High surge current capability  Glass passivated chip junction Mechanical Data Case : JEDEC TBS Molded plastic body Terminals : Solder plated, solderable per MIL-STD-750,Method 2026 Polarity : Polarity symbol marking on body Mounting Position : Any Weight : 0.003 ounce, 0.098 grams Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics Ratings at 25°C ambient temperature unlss otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. Parameter MDD TB10S UNITS 1000 700 1000 1.0 V V V A IFSM 30 A VF 0.95 V IR 5 100 uA RθJA 80 °C/W SYMBOLS Marking Code Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current Peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage drop per leg at 1A Maximum DC reverse current TA=25°C at rated DC blocking voltage TA=100°C Typical thermal resistance Operating temperature range storage temperature range VRRM VRMS VDC IF(AV) MDD TB2S MDD TB4S MDD TB6S 200 140 200 400 280 400 600 420 600 TJ -55 to +150 TSTG -55 to +150 MDD TB8S 800 560 800 pF °C °C NOTES:1.On glass epoxy P.C.B. mounted on 0.05x0.05''(1.3x1.3mm) pads 2.On aluminum substrate P.C.B. with on area of 0.8''x0.8''(20x20mm) mounted on 0.05X0.05''(1.3X1.3mm) solder pad 3.Thermal resistance form junction to ambient and junction to lead mounted on P.C.B. with 0.2X0.2''(5X5mm) copper pads. http://www.microdiode.com Rev:2024A1 Page :1 TB2S THRU TB10S Voltage Range - 40 to 200 V olts Current - 1.0 Ampere Ratings And Characteristic Curves Instantaneous Forward Current, (A) FIG.1 TYPICAL FORWARD CHARACTERISTICS FIG.2 FORWARD DERATING CURVE 1.0 1.0 Average Forward Rectified Current, (A) Aluminum Substrate 0.4 0.1 0.01 0.75 GLASS EPOXY P.C.B 0.5 0.25 RESISTIVE OR INDUCTIVE LOAD 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 0 Instantaneous Forward Voltage, ( V ) FIG.3 TYPICAL REVERSE CHARACTERISTICS 50 75 100 125 150 Ambient Temperature, (°C ) FIG.4 PEAK FORWARD SURGE CURRENT 35 Peak Forward Surge Current, (A) 100000 Instantaneous Reverse Leakage Current, ( A) 25 10000 1000 TA=100°C 100 TA=25°C 10 1.0 30 25 20 15 10 5 0 0 20 40 60 80 100 120 140 Percent Of Rated Peak Reverse Voltage, % 1 10 100 Number Of Cycles At 60Hz The cruve graph is for reference only, can't be the basis for judgment http://www.microdiode.com Rev:2024A1 Page :2