深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
产品规格书
SPECIFICATION
产品名称
Description
石英晶体谐振器
Crystal Unit
型号 · 标称频率
Type · Nominal Frequency
206 16.000MHz
规格书号
Specification .
JFWSG16020A104C
制作
DESIGNEDBY
审核
CHECKEDBY
批准
APPROBEDBY
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
杨
阳
何
珍
肖
琳
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
石英晶体谐振器(柱状)
RoHS Compliant Standard
TDXLF-206-16.000MHz20PF
STANDARD SPECIFICATIONS 標準規格
标称频率
Nominal Frequency
16.000MHz
负载电容
Load Capacitance
20pF
工作温度范围
Operating Temperature
-20℃ ~ +70℃
频率公差
Frequency Tolerance
±10ppm
温度频差
±10PPM(-20~+70 之间)
等效阻抗
<80Ω
激励电平
Level of Drive
50 U W
绝缘电阻:
50M(插脚间加 DC100V±5V)
年老化率
Aging
±5ppm/year
静电容
<5PF
25℃
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
可靠性 1Reliability(Mechanical and Environmental Endurance)
Page 1 of 2
NO
1
Test Items
振動
Vibration
衝擊
2
Shock
Test Method and Condition
Requirements
(1)振動頻 Vibration Frequency10 to 55Hz
頻率變化最大:±10ppm
(2)振動幅度 Vibration Amplitude 1.5mm
覆 蓋 The dipped surface of the
(3)周期 Cycle Time1-2min(10-55-10Hz)
leads should be at least 95%
(4)振動方向 Direction
covered with continuous new
X.Y.Z
(5)振動時間 Duration 2h/each direction
solder coating
從 75cm 高的地方自由跌落 3 次到 30mm 厚
頻 率 變 化 最 大 : ±
的 硬 木 板 上 3 Times free drop from 75cm
10ppmFrequency
height to hard wooden board of thickness
10ppm Max. 電 阻 變 化 最
more than 30mm
大 :5kohmResistance
Change: ±
Change:
5kohm Max.
3
晶體放入氦加壓罐內,充入氦氣壓力
漏 氣 率 小 於 :1x10 ¯ 8mbar.l/ s
0.5-0.6Mpa 保持 1 小時;然後使用氦質譜檢
Leakage:1x10¯8mbar.l/s Max.
氣密性
漏儀測試。Put crystal units into a hermetic
Leakage
container and Helium for 0.5-0.6Mpa,and
keep it for 1h;Check the leakage by a Helium
leak detector
4
可焊性
Solder ability
手工焊接耐热
5
將引線浸入完全熔化的焊錫鍋內 3-5s,焊
浸過引線面積的 95%以上被新
錫溫度 245℃±5℃Put the leads of
crystal
焊 錫 覆 蓋 The dipped surface of
units into solder melted tank for 3 to
the leads should be at least 95%
5sTemperature of solder melted tank is
covered with continuous new
245℃±5℃
solder coating
350℃±10℃,3+1/-0 sec
頻率變化最大:±10ppm
Soldering
Frequency Change: ± 10ppm
iron
Max.電阻變化最大:10kohm
resistance
Resistance Change: 10kohm Max.
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
推荐使用下面的波峰焊温度曲线进行波峰焊接。The WAVE SOLDERING
PROFILE
as
below
is
recommended:
波峰焊耐热
6
Wave soldering
resistance
可靠性 2Reliability(Mechanical and Environmental Endurance)
No
7
Test Items
Test Method and Condition
Page 2 of 2
Requirements
用 0.9kg(9N)的力持續拉晶體引線 30s±5s;用 0.45kg
引 線 無 異 常 The crystal
引線強度(引線
的力折引線成 90°2 次(折弯处离机体 1.5mm 以上); lead is not
直
晶
The crystal lead with the 0.9kg(9N)power(keep it for
)Lead
30s ± 5s)and bend the crystal lead 90° with 0.45kg
插
式
體
Strength(DIP)
a bnormity
power and two times (which you want to bend should
be more than 1.5mm from the case)
耐高溫能力 High
8
Temperature
Endurance
耐低溫能力 Low
9
Temperature
Endurance
晶體放置於 85℃±2℃環境中 2 小時後,常溫放置
1-2 小 時 The crystal units shall be put in somewhere
for 2 hours at temperature of 85℃±2℃,then keep it
for 1 to 2 hours under room temperature
晶體放置於-25℃ 環境中 2 小時後,常溫放置 1-2
小時 The crystal units shall be put in somewhere for 2
hours at temperature of -25 ℃ ,then keep it for 1 to 2
hours under room temperature
晶體放置於 40℃ 、相對濕度 90-95%環境中 48 小時
10
耐濕性 Humidity
Endurance
後,常溫放置 1-2 小時 The crystal units shall be put in
somewhere
at 40℃ in relative humidity of 90-95%
for 48 hours,then keep it for one or two hours under
頻率變化最大:±10ppm
Frequency Change:±
10ppm Max. 電阻變化
最大:5kohm Resistance
Change:5kohm Max.
room temperature
溫度從-40℃(保持 30 分鐘)升高到 100℃(保持
11
高 低 溫 迴 圈
30 分鐘)
,再降到-40℃(保持 30 分鐘)然後回到室
Temperature
溫 25℃完成一個迴圈,共計 5 個迴圈 Temperature
Cycle
shift from low(-40 ℃ ) to high(100 ℃ ,keep
30minutes),satisfy high(100 ℃ ) to low(-40 ℃ ,keep 30
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
minutes),then go up to room temperature for 5 cycles
12
鹽 霧 試 驗 Salt
Spray Test
晶體置於鹽霧濃度 5%,溫度 35℃的鹽霧室中 96 小時
外觀良好,可焊性良好
後,用水洗淨擦幹表面 Put the crystal units in the salt
The appearance shall has
spray room(salt density:5%)at the temperature of 35℃
no ab norm i t y
for 96 hours.Then clean it with water and dry its
soldering is good.頻率變
surface.
化 最 大 : ± 10ppm
Frequency
and
Change: ±
10ppm Max.電阻變化最
大
:5kohmResistance
Change:5kohm Max.
使用說明 Processing Instructions
下面的說明和資訊供用戶正確理解和使用我們公司的石英晶體系列產品,預防不
當的加工方式,對石英晶體的損壞,確保用戶設備的可靠性。
The following instructions and information are provided for the purpose of having
the user understand the proper way to process our crystal products to prevent
problems prior to use and enhance the reliability of the equipment to which they
are applied.
No.
PROCESSING INSTRUCTIONS
石英晶體意外跌落 When dropped by mistake
設計和製造的石英晶體本身具有耐衝擊能力,但是當石英晶體元件經受劇烈的機械衝擊,如跌落到
1
地板上或安裝期間劇烈震動時,在使用之前需要進行電性能確認
The crystal units are designed and manufactured to resist physical shocks.However,when the crystal units
are subjected to excessive impact such as being dropped onto the floor or giving shocks during
processing,need to make sure its satisfactory performance before using it.
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
焊接 Soldering
(1)使用電烙鐵焊接時,引線應該在 4 秒內焊接完畢,
電烙鐵溫度不能高於 350℃Lead wires should be
soldered within 4 seconds with the soldering iron heated to a temperature no higher than 350℃
(2)使用浸錫方式焊接時,引線應該在 10 秒內焊接完畢,焊錫溫度不能高於 260℃,並且注意不能
將整個晶體浸錫.推薦使用垂直安裝方式,避免熱力直接傳導到晶體上 In solder-dip processing,the
leads should be soldered within 10 seconds with a temperature no higher than 260℃.Mounting in upright
is recommendable to prevent the heat conduction directly to the body of the crystal unit.
(3)使用波峰焊接时,请参照下面的波峰焊温度曲线 The WAVE SOLDERING PROFILE as below is
recommended for TDXLF-308 tuning fork crystal re so n a t e rs.
2
使用說明 Processing Instructions
No.
PROCESSING INSTRUCTIONS
石英晶體彎腳 TO BEND THE LEAD of cylinder type products
(1)當圓柱狀晶體元件需要彎腳時,爲了防止彎腳時造成密封玻璃體的破裂,從彎腳處到晶體基座底
部距離應大於 1.5mm。推薦距離 3.0mm,並使用工裝夾具進行彎腳。When the lead of cylinder type
3
crystal units need to be bent,leave more than 1.5mm(3.0mm is recommendable) of lead from the case in
order to prevent from any cracks of the hermetic sealing glass at the root of the lead,and use a jig to bend
if possible.
(2)當圓柱狀晶體元件進行彎腳時,不要剝離引線的鍍層 When bending the
lead of cylinder type
crystal units,do not scrape off the soldering plating from the lead surface.
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
元件的安裝 MOUNTING
(1)爲了避免影響元件電性能或損壞元件,嚴禁將圓柱狀晶體元件外殼焊接在印製板上進行固定。
推薦使用橡膠粘結劑進行固定 Soldering the body of the cylinder type crystal units with PCB must be
4
≧1.5mm
(2)當用手工來彎曲引線時,請遵照下列方法 When the lead needs to be bent by hand,please follow the
instruction as below:用手指捏住圓柱晶體的外殼;用鑷子夾住引線要彎曲的部位,該部位離晶體基座
底部 1.5mm 以上(推薦 3.0mm);用鑷子夾住彎曲引線成 90°,不要用力拉引線。用力拉引線可能
造成引線根部的玻璃子破裂,而産生漏氣損壞元件電性能。Hold the body of the cylinder type crystal
unit in fingers;Pick at the part with twee z er,which you want to bend.There should be more than
1.5mm(3.0mm is recommended) from the body case;Bend the lead 90° by twee z er without pulling the
lead strongly.If pulling the lead strongly may cause any cracks of hermetic sealing glass at the root of the
lead and may cause the leakage and the characteristics to deteriorate.
石英晶體元件的清洗 CLEANING
(1)惡劣的超聲波清洗或超聲波焊接可能會影響和損壞石英晶體元件。如果您對晶體元件進行了超聲
波清洗,請一定在使用前確認晶體元件是否受到了影響和損壞 Crystal units may be sf f c ted and
5
destroyed at worst by supersonic cleaning or supersonic welding.Please be sure to check if your cleaning
and welding process sf f e c ts any damage to crystal units before using.
(2)有些清洗液也可能造成晶體元件的損壞,請在使用清洗液前確認該清洗液是否適用 Some kinds of
cleaning fluid may cause any damage to crystal units.Please be sure to check suitability of the cleaning
fluid in advance
貯存 STORAGE
石英晶體元件長時間貯存在高溫或高濕環境中,可能會影響頻率的穩定性或可焊性。請將晶體元件
6
貯存在正常的溫度和濕度環境中,避免陽光直射和露水凝結,避免貯存 6 個月以上再使用,拆封後
儘快裝配使用。Storage of crystal units under higher temperature or high humidity for a long term may
affects frequency stability or sold era b i y .Please store the crystal units under the normal temperature and
humidity without exposing to direct sunlight and dew condensation
包装 PACKING
Packing For Pb Free Parts:
1.INNER BOX:(Unit:mm)
1000pcs/bag
10bagsX1000pcs=10000pcs/box
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
深 圳 市 晶 发 电 子 有 限 公 司
SHENZHEN JINGFA ELECTRONICS CO.,LTD
客供品进料检验标签
厂
商
10 INNER BOX x10000pcs=100000pcs
Revision
A
Revised
A
Date
6-Feb.-2016
records
C
Issued
by
initial release
Hold
Type
工厂地址:深圳市宝安区福永安达电子工业区 4 栋 6 楼
电话:0755-23001622
传真:0755-26741500 网址:www.jingfadianzi.com
206
很抱歉,暂时无法提供与“JFWSG16020A104C”相匹配的价格&库存,您可以联系我们找货
免费人工找货