PL8604

SMT POWER INDUCTORS Toroid - Military/Aerospace POGO Series Ruggedized Ruggedized header with POGO pins for secure board mounting Current Rating: up to 8.3ADC Inductance Range: 2.0µH to 336µH Moisture Sensitivity Level: 1 Electrical Specifications @ 25 °C — Operating Temperature - 40 °C to +130 °C 9 Inductance @ Irated (µH MIN) Irated DCR (MAX) ET Part (A) (V-µsec) Number (mΩ) POGO 25 2.0 8.30 8.0 7.31 PL8600 2.4 7.20 10.9 7.81 PL8601 5.0 5.20 19.0 11.72 PL8602 7.0 4.16 16.0 14.61 PL8600 9.3 3.80 30 16.12 PL8603 8.4 3.78 21.8 15.62 PL8601 14.1 3.10 45.5 19.73 PL8604 19.8 2.60 66.5 23.45 PL8605 17.9 2.60 38.0 23.43 PL8602 29.3 2.20 101 28.50 PL8606 33.8 1.89 60 32.25 PL8603 42.6 1.80 151 34.49 PL8607 50.9 1.54 91 39.46 PL8604 61.3 1.50 222 40.85 PL8608 71.5 1.30 133 46.90 PL8605 84.2 1.20 318 46.22 PL8609 106.1 1.07 202 57.00 PL8606 154.2 0.89 302 68.99 PL8607 218.9 0.74 444 81.70 PL8608 295.0 0.64 636 92.43 PL8609 NOTES: 1. Temperature rise is 50°C in typical buck or boost circuits at 250kHz and with the reference ET applied to the inductor. 2. Total loss in the inductor is 380mWatts for a 50°C temperature rise above ambient. 3. To estimate temperature rise in a given application, determine copper and core losses, divide by 380 and multiply by 50. 4. For the copper loss, calculate IDC2 X RN. 5. For core loss, using frequency (f) and operating flux density (B), calculate 6.11 x 10-18 x B2.7 x f2.04. Mechanical Inductance @0ADC (µH ±10%) 2.2 2.6 5.5 8.75 10.4 10.4 15.7 22.1 22.45 32.8 41.7 47.6 62.8 67.5 88.2 91.0 131.0 190.3 270.2 364.0 (V-µsec) 1 Amp DC H1 (Orsted) 1.20 1.33 1.93 2.41 2.65 2.65 3.25 3.86 3.86 4.70 5.30 5.66 6.51 6.75 7.71 7.83 9.40 11.33 13.50 15.66 5.43 5.97 8.69 10.86 11.95 11.95 14.66 17.38 17.38 21.18 23.89 25.52 29.32 30.41 34.75 35.30 42.36 51.05 60.82 70.59 100 Gauss ET100 Connection Parallel Parallel Parallel Series Parallel Series Parallel Parallel Series Parallel Series Parallel Series Parallel Series Parallel Series Series Series Series 6. For flux density (B), calculate ET (V-µsec) for the application, divide by ET100 from the table, and multiply by 100. 7. Limit the DC bias (H) to 46 orsteds. Calculate H by multiplying H1 from the table by IDC of the application. 8. The maximum DCR listed is approximately 17% over the nominal DCR. 9. Optional Tape & Reel packaging can be ordered by adding a "T" suffix to the part number (i.e. PL8600 becomes PL8600T). Electrical Schematic 4 3 2 4 1 1 3 www.inrcore.com M114.D (07/20) SMT POWER INDUCTORS Toroid - Military/Aerospace POGO Series Ruggedized For More Information Global Sales Representatives and Lo cations: http://www.inrcore.com iNRCORE,LLC 311 Sinclair Road Bristol, PA 19007-6812 U.S.A Tel: + 1.215.781.6400 Fax: +1.215.7816430 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2020. iNRCORE, LLC. All rights reserved. 2 www.inrcore.com M114.D (07/20)