0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
EVA-M8M-0-10

EVA-M8M-0-10

  • 厂商:

    U-BLOX(优北罗)

  • 封装:

    TFLGA42

  • 描述:

    EVA-M8M-0-10

  • 详情介绍
  • 数据手册
  • 价格&库存
EVA-M8M-0-10 数据手册
EVA-M8M u-blox M8 concurrent GNSS modules Data Sheet Highlights: · Industry’s smallest GNSS module · Concurrent reception of up to 3 GNSS (GPS, Galileo, GLONASS, BeiDou) · Security and integrity protection · Support all satellite augmentation systems · Advanced jamming and spoofing detection · Backward compatible with EVA-7M www.u-blox.com UBX-160007405 - R02 EVA-M8M - Data Sheet Document Information Title EVA-M8M Subtitle u-blox M8 concurrent GNSS modules Document type Data Sheet Document number UBX-160007405 Revision and date R02 Document status Production Information 21-Jul-2016 Document status explanation Objective Specification Document contains target values. Revised and supplementary data will be published later. Advance Information Document contains data based on early testing. Revised and supplementary data will be published later. Early Production Information Document contains data from product verification. Revised and supplementary data may be published later. Production Information Document contains the final product specification. This document applies to the following products: Product name Type number ROM/FLASH version EVA-M8M EVA-M8M-0-10 ROM SPG 3.01 / Flash FW SPG 3.01 PCN reference UBX-16012546 EVA-M8M EVA-M8M-1-10 ROM SPG 3.01 / Flash FW SPG 3.01 UBX-16012546 u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or any part thereof without the express permission of u-blox is strictly prohibited. The information contained herein is provided “as is” and u-blox assumes no liability for the use of the information. No warranty, either express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose of the information. This document may be revised by u-blox at any time. For most recent documents, visit www.u-blox.com. Copyright © 2016, u-blox AG. u-blox® is a registered trademark of u-blox Holding AG in the EU and other countries. ARM® is the registered trademark of ARM Limited in the EU and other countries. UBX-160007405 - R02 Production Information Page 2 of 32 EVA-M8M - Data Sheet Contents Contents.............................................................................................................................. 3 1 Functional description.................................................................................................. 6 1.1 Overview .............................................................................................................................................. 6 1.2 1.3 Product features ................................................................................................................................... 6 Performance ......................................................................................................................................... 7 1.4 Block diagram....................................................................................................................................... 8 1.5 Supported GNSS Constellations ............................................................................................................ 8 1.5.1 GPS ............................................................................................................................................... 9 1.5.2 GLONASS ...................................................................................................................................... 9 1.5.3 1.5.4 BeiDou .......................................................................................................................................... 9 Galileo ........................................................................................................................................... 9 1.6 Assisted GNSS (A-GNSS) ....................................................................................................................... 9 1.6.1 1.6.2 AssistNow™ Online ....................................................................................................................... 9 AssistNow™ Offline .................................................................................................................... 10 1.6.3 AssistNow™ Autonomous ........................................................................................................... 10 1.7 Augmentation Systems ....................................................................................................................... 10 1.7.1 Satellite-Based Augmentation System (SBAS) ............................................................................... 10 1.7.2 QZSS ........................................................................................................................................... 10 1.7.3 1.7.4 IMES............................................................................................................................................ 10 Differential GPS (D-GPS) .............................................................................................................. 11 1.8 Broadcast navigation data and satellite signal measurement ............................................................... 11 1.9 1.10 Odometer ........................................................................................................................................... 11 Data logging ................................................................................................................................... 11 1.11 Geofenceing ................................................................................................................................... 11 1.12 1.13 Message Integrity Protection ........................................................................................................... 11 Spoofing Detection ......................................................................................................................... 12 1.14 EXTINT: External interrupt ............................................................................................................... 12 1.14.1 1.14.2 Pin Control .................................................................................................................................. 12 Aiding ......................................................................................................................................... 12 1.15 TIMEPULSE ...................................................................................................................................... 12 1.16 1.17 Protocols and interfaces .................................................................................................................. 12 Interfaces ........................................................................................................................................ 13 1.17.1 UART ........................................................................................................................................... 13 1.17.2 1.17.3 USB ............................................................................................................................................. 13 SPI ............................................................................................................................................... 13 1.17.4 Display Data Channel (DDC) ........................................................................................................ 13 1.17.5 1.17.6 Serial Quad Interface (SQI) ........................................................................................................... 13 Interface selection (D_SEL) ........................................................................................................... 13 1.18 Configurable Input Output pins ...................................................................................................... 14 1.19 Safe Boot Mode .............................................................................................................................. 14 UBX-160007405 - R02 Production Information Contents Page 3 of 32 EVA-M8M - Data Sheet 1.20 1.21 System reset.................................................................................................................................... 14 Clock generation ............................................................................................................................ 14 1.21.1 Oscillator ..................................................................................................................................... 14 1.21.2 Real-Time Clock (RTC) ................................................................................................................. 14 1.22 Power Management ....................................................................................................................... 15 1.22.1 DC/DC converter ......................................................................................................................... 15 1.22.2 1.22.3 Power Mode Setup ...................................................................................................................... 15 Continuous Mode ....................................................................................................................... 15 1.22.4 Power Save Mode ....................................................................................................................... 15 1.23 Antenna .......................................................................................................................................... 16 1.23.1 Active antenna control (ANT_OFF) ............................................................................................... 16 1.23.2 2 3 Active Antenna supervisor and short circuit detection.................................................................. 16 Pin definition .............................................................................................................. 17 2.1 Pin assignment ................................................................................................................................... 17 2.2 Pin name changes............................................................................................................................... 19 Electrical specification ................................................................................................ 20 3.1 Absolute maximum rating .................................................................................................................. 20 3.2 Operating conditions .......................................................................................................................... 21 3.2.1 DC electrical characteristic ........................................................................................................... 21 3.2.2 3.3 3.4 Indicative power requirements ............................................................................................................ 22 SPI timing diagrams ............................................................................................................................ 23 3.4.1 3.5 Baseband parameters .................................................................................................................. 22 Timing recommendations ............................................................................................................ 24 DCC timing diagrams ......................................................................................................................... 24 4 Mechanical specification ............................................................................................ 25 5 Reliability tests and approvals .................................................................................. 26 5.1 5.2 6 Reliability tests .................................................................................................................................... 26 Approvals ........................................................................................................................................... 26 Product handling ........................................................................................................ 27 6.1 Packaging ........................................................................................................................................... 27 6.1.1 Reels ........................................................................................................................................... 27 6.1.2 6.2 6.3 Tapes .......................................................................................................................................... 27 Moisture Sensitivity Levels ................................................................................................................... 28 ESD handling precautions ................................................................................................................... 28 7 Default messages ....................................................................................................... 29 8 Labeling and ordering information........................................................................... 30 8.1 Product labeling.................................................................................................................................. 30 8.2 8.3 Explanation of product codes ............................................................................................................. 30 Ordering codes ................................................................................................................................... 30 UBX-160007405 - R02 Production Information Contents Page 4 of 32 EVA-M8M - Data Sheet Related documents........................................................................................................... 31 Revision history ................................................................................................................ 31 Contact .............................................................................................................................. 32 UBX-160007405 - R02 Production Information Contents Page 5 of 32 EVA-M8M - Data Sheet 1 Functional description 1.1 Overview The EVA-M8M GNSS modules feature the exceptional performance of the u-blox M8 concurrent positioning engine (receiving GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS signals). The EVA-M8M series modules deliver high sensitivity and minimal acquisition times in the ultra compact EVA form factor. The EVA-M8M series modules comes in two variants: EVA-M8M-0 defaults to GPS/QZSS/GLONASS whereas EVA-M8M-1 defaults to GPS/QZSS/BeiDou. The EVA-M8M series is an ideal solution for cost and space-sensitive applications. It is easy to design in, only requiring an external GNSS antenna in most applications. The layout of the EVA-M8M series is especially designed to ease the customer’s design and limit near-field interferences, since RF and digital domains are kept separate. The EVA-M8M series uses a crystal oscillator for lower system costs. Like other u-blox GNSS modules, the EVA-M8M modules use components selected for functioning reliably in the field over the full operating temperature range. In addition, EVA-M8M provides an SQI interface for optional external FLASH, for future firmware upgrades and improved A-GNSS performance. EVA-M8M supports message integrity protection, geofencing, and spoofing detection. With a dual-frequency RF front-end, the u-blox M8 concurrent GNSS engine is able to intelligently use the highest number of visible satellites from three GNSS (GPS and Galileo, together with GLONASS or BeiDou) systems for reliable positioning. The EVA-M8M can be easily integrated in manufacturing, thanks to the QFN-like package. The modules are available in 500 pieces/reel, ideal for small production batches. The modules combine a high level of integration capability with flexible connectivity options in a miniature package. This makes the EVA-M8M modules perfectly suited for small size and cost-sensitive industrial and wearable devices. The DDC (I2C compliant) interface provides connectivity and enables synergies with u-blox cellular modules. The EVA-M8M modules are manufactured in ISO/TS 16949 certified sites and qualified as stipulated in the JESD47 standard. 1.2 Product features UBX-160007405 - R02 Production Information Functional description Page 6 of 32 EVA-M8M - Data Sheet 1.3 Performance Parameter Specification Receiver type 72-channel u-blox M8 engine GPS/QZSS L1C/A, GLONASS L1OF, BeiDou B1l, Galileo E1B/C, SBAS L1C/A: WAAS, EGNOS, MSAS, GAGAN Accuracy of time pulse signal RMS 99% Frequency of time pulse signal 0.25 Hz…10 MHz (configurable) Operational limits 1 Dynamics £4g Altitude 50,000 m Velocity 500 m/s Velocity accuracy 2 Heading accuracy 30 ns 60 ns 0.05m/s 2 0.3 degrees GNSS GPS & GLONASS GPS GLONASS BeiDou Galileo Horizontal position accuracy 3 2.5 m 2.5 m 4.0 m 3.0 m TBD 18 Hz 18 Hz 18 Hz Max navigation update rate ROM 10 Hz 18 Hz FLASH 5 Hz 10 Hz 10 Hz 10 Hz 10 Hz Time-To-First-Fix 4 Cold start 26 s 30 s 31 s 39 s 57 s Hot start 1s 1s 1s 1s 1s Aided starts 5 3s 3s 3s 7s 7s Tracking & Navigation –164 dBm –164 dBm -163 dBm -160 dBm -154 dBm 6 Sensitivity Reacquisition –160 dBm –159 dBm -156 dBm -155 dBm -152 dBM Cold start –148 dBm –147 dBm -145 dBm –143 dBm -133 dBm Hot start –157 dBm –156 dBm -155 dBm -155 dBm -151 dBm Table 1: EVA-M8M performance in different GNSS modes 1 2 3 4 5 6 Assuming Airborne < 4 g platform 50% @ 30m/s CEP, 50%, 24 hours static, -130 dBm, > 6 SVs All satellites at -130 dBm, except Galileo at -127 dBm Dependent on aiding data connection speed and latency Demonstrated with a good external LNA UBX-160007405 - R02 Production Information Functional description Page 7 of 32 EVA-M8M - Data Sheet 1.4 Block diagram Figure 1: EVA-M8M block diagram 1.5 Supported GNSS Constellations The EVA-M8M modules are concurrent GNSS receivers and can receive and track multiple GNSS systems (GPS, GLONASS, Galileo, BeiDou and QZSS signals). Owing to the dual-frequency RF front-end architecture, either GLONASS or BeiDou can be processed concurrently with GPS and Galileo signals, providing reception of three GNSS systems. The EVA-M8M series has two variants: EVA-M8M-0 (default: concurrent GPS/QZSS/SBAS and GLONASS) and EVA-M8M-1 (default: concurrent GPS/QZSS/SBAS and BeiDou). If power consumption is a key factor, then the EVA-M8M should be configured for single GNSS operation using GPS or GLONASS or BeiDou and disabling QZSS and SBAS. The module can be configured to receive any single GNSS constellation or any of the set of permissible combinations shown below. GPS Galileo GLONASS BeiDou • • – – • • • – • • – • • – • – EVA-M8M-0 default • – – • EVA-M8M-1 default – • • – – – • – – • • • Table 2: Permissible GNSS combinations (• = enabled) The augmentation systems: SBAS and QZSS can be enabled only if GPS operation is configured. Galileo is not enabled as the default configuration. UBX-160007405 - R02 Production Information Functional description Page 8 of 32 EVA-M8M - Data Sheet When the EVA-M8M-1 variant is attached with an external SQI flash without running flash firmware, the default concurrent reception of GPS/QZSS/SBAS and BeiDou remains unchanged. If the flash is also used for execution of firmware update, the default reception will be reset to GPS/QZSS/SBAS and GLONASS. See the EVA-8M / EVA-M8 Hardware Integration Manual [1] for more information on how to preset default concurrent reception of GPS/QZSS/SBAS and BeiDou. 1.5.1 GPS The EVA-M8M positioning modules are designed to receive and track the L1C/A signals provided at 1575.42 MHz by the Global Positioning System (GPS). 1.5.2 GLONASS The EVA-M8M modules can receive and process the GLONASS satellite system as an alternative to the US-based Global Positioning System (GPS). The u-blox EVA-M8M series is designed to receive and track the L1OF signals GLONASS provided at 1602 MHz + k*562.5 kHz, where k is the satellite’s frequency channel number (k = –7,..., 5, 6). The ability to receive and track GLONASS L1OF satellite signals allows design of GLONASS receivers where required by regulations. To take advantage of GPS and GLONASS, dedicated hardware preparation must be made during the design-in phase. See the EVA-8M / EVA-M8 Hardware Integration Manual [1] for u-blox design recommendations. 1.5.3 BeiDou The EVA-M8M modules can receive and process the B1I signals broadcast at 1561.098 MHz from the BeiDou Navigation Satellite System. The ability to receive and track BeiDou B1 satellite signals in conjunction with another constellation results in higher coverage, improved reliability and better accuracy. Currently, BeiDou is not fully operational globally and provides Chinese regional coverage only. Global coverage is scheduled for 2020. 1.5.4 Galileo The EVA-M8M positioning modules can receive and track the E1-B/C signals centered on the GPS L1 frequency band. GPS and Galileo signals can be processed concurrently together with BeiDou or GLONASS signals, enhancing coverage, reliability and accuracy. The SAR return link message (RLM) parameters for both short and long versions are decoded by the receiver and made available to users via UBX proprietary messages. Galileo has been implemented according to ICD release 1.2 (November 2015) and verified with live signals from the Galileo in-orbit validation campaign. Since the Galileo satellite system has not yet reached Initial (IOC) nor Full Operational Capability (FOC), changes to the Galileo signal specification (OS SIS ICD) remain theoretically possible. u-blox therefore recommends to use Flash memory in designs utilizing Galileo signals in order to allow for a FW update in the unlikely event of a change to the Galileo signal specification (OS SIS ICD). Galileo reception is by default disabled, but can be enabled by sending a configuration message (UBX-CFGGNSS) to the receiver. See the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2] for more information. 1.6 Assisted GNSS (A-GNSS) Supply of GNSS receiver assistance information, such as ephemeris, almanac, rough user position and time, will reduce the time to first fix significantly and improve acquisition sensitivity. All u-blox M8030 based products support the u-blox AssistNow Online and AssistNow Offline A-GNSS services, support AssistNow Autonomous, and are OMA SUPL compliant. 1.6.1 AssistNow™ Online With AssistNow Online, an Internet connected host downloads assistance data from the u-blox AssistNow Online service to the receiver at system start-up. The Multi-GNSS Assistance (MGA) service is an HTTP protocol based network operator independent service. UBX-160007405 - R02 Production Information Functional description Page 9 of 32 EVA-M8M - Data Sheet Supplying assistance information, such as ephemeris, almanac, a rough last position and time, can reduce the time to first fix significantly and improve acquisition sensitivity. The AssistNow Online service provides data for GPS, GLONASS, BeiDou, Galileo and QZSS. 1.6.2 AssistNow™ Offline With the AssistNow Offline service, users can download long-term orbit data over the Internet at their convenience. The orbit data can be stored in the GNSS receiver’s SQI flash memory or alternatively within the memory of the application processor. The function requires no connectivity at system start-up, enabling a position fix within seconds, even when no network is available. AssistNow Offline offers augmentation for up to 35 days. AssistNow Offline service provides data for GPS and GLONASS only, BeiDou and Galileo are not currently supported 1.6.3 AssistNow™ Autonomous AssistNow Autonomous provides aiding information without the need for a host or external network connection. Based on previous broadcast satellite ephemeris data downloaded to and stored by the GNSS receiver, AssistNow Autonomous automatically generates accurate predictions of satellite orbital data (“AssistNow Autonomous data”) that is usable for future GNSS position fixes. The concept capitalizes on the periodic nature of GNSS satellites; by capturing strategic ephemeris data at specific times of the day, the receiver can predict accurate satellite ephemeris for up to six days after initial reception. u-blox’s AssistNow Autonomous benefits are: · · · · Faster fix in situations where GNSS satellite signals are weak No connectivity required Compatible with AssistNow Online and Offline (can work stand-alone, or in tandem with these services) No integration effort; calculations are done in the background, transparent to the user. For best AssistNow Autonomous performance and data storage, the use of an SQI flash memory is recommended for EVA-M8M modules, otherwise only GPS satellites are used and the prediction time decreases to three days. 1.7 Augmentation Systems 1.7.1 Satellite-Based Augmentation System (SBAS) u-blox EVA-M8M positioning modules support SBAS. These systems supplement GNSS data with additional regional or wide area GPS augmentation data. The system broadcasts range correction and integrity information via satellite which can be used by GNSS receivers to improve resulting precision. SBAS satellites can be used as additional satellites for ranging (navigation), further enhancing availability. The following SBAS types are supported: GAGAN, WAAS, EGNOS and MSAS. For more details see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.7.2 QZSS The Quasi-Zenith Satellite System (QZSS) is a regional navigation satellite system that transmits additional GPS L1 C/A signals for the Pacific region covering Japan and Australia. EVA-M8M positioning module is able to receive and track these signals concurrently with GPS signals, resulting in better availability especially under challenging signal conditions, e.g. in urban canyons. The L1- SAIF signal provided by QZSS can be enabled for reception via a GNSS configuration message 1.7.3 IMES The Japanese Indoor MEssaging System (IMES) system is used for indoor position reporting using low-power transmitters which broadcast a GPS–like signal. EVA-M8M module can be configured to receive and demodulate the signal to provide an in-door location estimate. UBX-160007405 - R02 Production Information Functional description Page 10 of 32 EVA-M8M - Data Sheet This service is authorized and available only in Japan. IMES reception is disabled by default 1.7.4 Differential GPS (D-GPS) u-blox EVA-M8M modules support Differential-GPS data according to RTCM 10402.3 [4]. The use of DifferentialGPS data improves GPS position accuracy. The RTCM implementation supports the following RTCM 2.3 messages: Message Type Description 1 Differential GPS Corrections 2 3 Delta Differential GPS Corrections GPS Reference Station Parameters 9 GPS Partial Correction Set Table 3: Supported RTCM 2.3 messages RTCM correction cannot be used together with SBAS. For more information see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.8 Broadcast navigation data and satellite signal measurement The EVA-M8M can output all the GNSS broadcast data upon reception from tracked satellites. This includes all the supported GNSS signals plus the augmentation services SBAS, QZSS and IMES. The receiver also makes available the tracked satellite signal information, i.e. raw code phase and Doppler measurements in a form aligned to the ETSI mobile cellular location services protocol (RRLP). For more information see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.9 Odometer The odometer function provides information on travelled ground distance (in meters) based on the position and Doppler-based velocity output from the navigation solution. For each computed distance since the last odometer reset, the odometer estimates a 1-sigma accuracy value. The total cumulative ground distance is maintained and saved in the BBR memory. The odometer feature is disabled by default. For more information see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.10 Data logging The EVA-M8M modules can be used in data logging applications if external flash is use. The data logging feature enables continuous storage of position, velocity and time information to an onboard SQI flash memory (at least 16 Mbit).It can also log the distance from the odometer. The information can be downloaded from the receiver later for further analysis or for conversion to a mapping tool. For more information see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.11 Geofenceing The u-blox EVA-M8M modules support up to four circular Geofenceing areas defined on the Earth’s surface using a 2D model. Geofencing is active when at least one Geo-fence is defined, the current status can be found by polling the receiver. A GPIO pin can be nominated to indicate status to e.g. wake up a host on activation. 1.12 Message Integrity Protection The EVA-M8M modules provide a function to detect third party interference with the UBX message steam sent from receiver to host. The security mechanism ‘signs’ nominated messages via a subsequent UBX message. This UBX-160007405 - R02 Production Information Functional description Page 11 of 32 EVA-M8M - Data Sheet message signature is then compared with one generated by the host to determine if the message data has been altered. The signature algorithm seed can use one fixed secret ID-key set by eFuse in production and a dynamic ID-key set by the host, enabling users to detect ‘man-in-the-middle’ style attacks. 1.13 Spoofing Detection Spoofing is a process whereby a malicious third party tries to control the reported position via a ‘fake’ GNSS broadcast signal. This may result in the form of reporting incorrect position, velocity or time. To combat against this, the EVA-M8M modules include spoofing detection measures to alert the host when signals appear to be suspicious. The receiver combines a number of checks on the received signals looking for inconsistencies across several parameters. This feature does not guarantee to detect all spoofing attacks. 1.14 EXTINT: External interrupt EXTINT is an external interrupt pin with fixed input voltage thresholds with respect to VCC_IO. It can be used for control of the receiver or for aiding. For more information about how to implement and configure these features, see the u-blox 8 / u-blox M8 Receiver Description including Protocol Specification [2] and the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 1.14.1 Pin Control The pin control feature allows overriding the automatic active/inactive cycle of Power Save Mode. The state of the receiver can be controlled through the EXTINT pin. The receiver can also be forced OFF using EXTINT when Power Save Mode is not active. 1.14.2 Aiding The EXTINT pin can be used to supply time or frequency aiding data to the receiver. For time aiding, the time can be supplied using hardware time synchronization where an accurate time pulse is connected to the EXTINT pin. Frequency aiding can be implemented by connecting a periodic rectangular signal with a frequency up to 500 kHz and arbitrary duty cycle (low/high phase duration must not be shorter than 50 ns) to the EXTINT pin, and providing the applied frequency value to the receiver using UBX messages. 1.15 TIMEPULSE A configurable time pulse signal is available with u-blox EVA-M8M series modules. The TIMEPULSE output generates pulse trains synchronized with GPS or UTC time grid with intervals configurable over a wide frequency range. Thus it may be used as a low frequency time synchronization pulse or as a high frequency reference signal. By default the time pulse signal is configured to 1 pulse per second. For more information see the u-blox 8 / u-blox M8 Receiver Description including Protocol Specification [2]. 1.16 Protocols and interfaces Protocol Type NMEA 0183, version 4.0 (V2.3 or V4.1 configurable ) Input/output, ASCII, UBX Input/output, binary, u-blox proprietary RTCM Input, messages 1, 2, 3, 9 Table 4: Available Protocols UBX-160007405 - R02 Production Information Functional description Page 12 of 32 EVA-M8M - Data Sheet 2 All protocols are available on UART, USB, DDC (I C compliant) and SPI. For specification of the various protocols see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.17 Interfaces A number of interfaces are provided either for data communication or memory access. The embedded firmware uses these interfaces according to their respective protocol specifications. 1.17.1 UART The EVA-M8M modules make use of a UART interface, which can be used for communication to a host. It supports configurable baud rates. For supported transfer rates see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. Designs must allow access to the UART and the SAFEBOOT_N pin for future service, updates and reconfiguration. 1.17.2 USB A USB interface, which is compatible to USB version 2.0 FS (Full Speed, 12 Mbit/s), can be used for communication as an alternative to the UART. The pull-up resistor on pin USB_DP is integrated to signal a fullspeed device to the host. The VDD_USB pin supplies the USB interface. The u-blox USB (CDC-ACM) driver supports Windows Vista plus Windows 7 and 8 operating systems. A separate driver (CDC-ACM) is not required for Windows 10 which has a built-in USB-serial driver. However, plugging initially into an internet connected Windows 10 PC, will down-load the u-blox combined sensor and VCP driver package. USB drivers can be down-loaded from the u-blox web site, www.u-blox.com. 1.17.3 SPI The SPI interface is designed to allow communication to a host CPU. The interface can be operated in slave mode only. The maximum transfer rate using SPI is 125 kB/s and the maximum SPI clock frequency is 5.5 MHz. Note that SPI is not available in the default configuration, because its pins are shared with the UART and DDC interfaces. The SPI interface can be enabled by connecting D_SEL to ground (see section 1.17.6). In this case the DDC interface for data communication is no longer available. 1.17.4 Display Data Channel (DDC) 2 An I C compliant DDC interface is available for communication with an external host CPU. The interface can be operated in slave mode only. The DDC protocol and electrical interface are fully compatible with Fast-Mode of 2 the I C industry standard. Since the maximum SCL clock frequency is 400 kHz, thus the maximum transfer rate is 400 kbit/s. 2 2 The DDC interface is I C Fast Mode compliant. For timing parameters consult the I C standard. The maximum bit rate is 400 kb/s. The interface stretches the clock when slowed down while serving interrupts, so real bit rates may be slightly lower. 1.17.5 Serial Quad Interface (SQI) An SQI is available in EVA-M8M series for connecting the modules with an optional external flash memory. The flash memory is required for firmware updates and for data logging. In addition, it can be used to store configurations and to save AssistNow Offline and AssistNow Autonomous data. For more information see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 1.17.6 Interface selection (D_SEL) At startup the D_SEL pin determines which data interfaces are used for communication. If D_SEL is set to logical “1” or is not connected, UART and DDC become available. If D_SEL is set to logical “0”, i.e. connected to GND, the EVA-M8M modules can communicate to a host via SPI. UBX-160007405 - R02 Production Information Functional description Page 13 of 32 EVA-M8M - Data Sheet 16 (D_SEL)=”1” (left open) UART TXD (D_SEL)=”0” (connected to GND) SPI MISO 15 29 UART RXD DDC SCL SPI MOSI SPI CLK 30 DDC SDA SPI CS_N Pin # Table 5: Data interface selection by D_SEL 1.18 Configurable Input Output pins Configuration settings can be modified for several Input/Output pins with either UBX configuration messages or pin selection. This flexible configuration options allow the receivers to be optimally configured for specific applications requirements. The modified settings remain either permanent or effective until power-down or reset depending on the case. Customer can activate or remap the following pins on EVA-M8M series: 1. Selection of either DDC or UART TXD/RXD pins interface using D_SEL pin. See section 1.17.6. 2. Selection of antenna supervision pins. See section 1.23. 3. Selection of external interrupt pins. See section 1.14. 4. Configuration of Timepulse. See section 1.15. For more information see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 1.19 Safe Boot Mode If Pin33 (SAFEBOOT_N) is set to logical “0” at startup, the EVA-M8M receivers enter Safe Boot Mode. In this mode the receiver does not calculate positioning data, but is in a defined state that allows such actions as programming the flash memory in production, or recovering a corrupted flash memory. For more information about Safe Boot Mode see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 1.20 System reset The EVA-M8M series provides a RESET_N pin to reset the system and Real-Time Clock (RTC). The RESET_N pin should be only used in critical situations to recover the system. 1.21 Clock generation 1.21.1 Oscillator The EVA-M8M modules use a 26 MHz crystal oscillator for lower system costs. Like other u-blox GNSS modules, the EVA-M8M modules use components selected for functioning reliably in the field over the full operating temperature range. 1.21.2 Real-Time Clock (RTC) The use of the RTC Clock may be optionally used to maintain time in the event of power failure at VCC_IO. The RTC is required for hot start, warm start, AssistNow Autonomous, AssistNow Offline and some Power Save Mode operations. The use of the RTC is optional. The time information can be generated in one of these ways: · by connecting to an external RTC crystal (for lower battery current – default mode) · by sharing from another RTC oscillator used within the application (for lowest system costs and smallest size) · from deriving RTC time from the onboard 26 MHz crystal oscillator (for low system costs and small size) If the main supply voltage fails and a battery is connected to V_BCKP, parts of the baseband section switch off, but the RTC still runs, providing a timing reference for the receiver. This operating mode is called Hardware Backup Mode, which enables all relevant data to be saved in the backup RAM to later allow a hot or warm start. UBX-160007405 - R02 Production Information Functional description Page 14 of 32 EVA-M8M - Data Sheet For more information about crystal operation and configuration, see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. If neither backup RAM nor RTC are used, the backup battery is not needed and V_BCKP should be connected to VCC_IO. 1.22 Power Management u-blox M8 technology offers a power-optimized architecture with built-in autonomous power saving functions to minimize power consumption at any given time. Furthermore, the receiver can be used in two operating modes: Continuous mode for best performance or Power Save Mode for optimized power consumption. In addition, a high efficiency DC/DC converter is integrated to allow low power consumption even for higher main supply voltages. 1.22.1 DC/DC converter EVA-M8M modules integrate a DC/DC converter, allowing reduced power consumption by up to 50%, especially when using a main supply voltage above 2.5 V. For more information, see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 1.22.2 Power Mode Setup The EVA-M8M modules can be configured to run in either continuous or a choice of Power Save mode configurations. A template of power mode settings can be used to easily select typical power mode setups to cover the majority of users’ requirements. For specific power saving applications, the user has the option to fully configure via the power save mode configuration. More information, see section 1.22.4. The EVA-M8M module’s power mode setup offers a choice of continuous operation and preset Power Save Mode Configurations. · Continuous (default) mode for best GNSS performance vs power consumption · Continuous with no compromise in power consumption · A 1 Hz cyclic tracking mode for aggressive power reduction · Choice of 2 or 4 Hz cyclic tracking modes for typical wearable applications · ON/OFF interval mode 7 1.22.3 Continuous Mode Continuous Mode uses the acquisition engine at full performance resulting in the shortest possible TTFF and the highest sensitivity. It searches for all possible satellites until the Almanac is completely downloaded. The receiver then switches to the tracking engine to lower power consumption. Thus, a lower tracking current consumption level will be achieved when: · A valid GNSS position is obtained · The entire Almanac has been downloaded · The Ephemeris of each satellite in view is valid 1.22.4 Power Save Mode For specific power saving applications outside the typical preset power mode setups, users can configure a tailored Power Save Mode. 7 Single GNSS constellation configuration only UBX-160007405 - R02 Production Information Functional description Page 15 of 32 EVA-M8M - Data Sheet Power Save Mode provides two dedicated methods, ON/OFF and Cyclic tracking, that reduce average current consumption in different ways to match the needs of the specific application. These operations can be set by using a specific UBX message. For more information about power management strategies, see the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2]. 1.23 Antenna 8 9 The EVA-M8M modules are designed for use with passive and active antennas. Parameter Specification Antenna Type Passive and active antenna Active Antenna Recommendations Minimum gain Maximum gain Maximum noise figure For Passive antenna, an external LNA is mandatory to achieve the performance specified in this document 15 dB (to compensate signal loss in RF cable) 50 dB 2 dB Table 6: Antenna recommendations and specifications for EVA-M8M modules 1.23.1 Active antenna control (ANT_OFF) The ANT_OFF Pin can be used to turn on and off an external LNA or an active antenna. This reduces power consumption in Power Save Mode (Backup mode). This pin is available in EVA-M8M modules. ANT_OFF pin polarity can be changed. For more information about active antenna control, see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 1.23.2 Active Antenna supervisor and short circuit detection An antenna supervisor is available with the EVA-M8M modules and requires external components. The antenna supervisor enables the receiver to detect short circuits at the active antenna using the ANT_OFF and ANT_OK pins (activated per default) and to shut down the voltage bias immediately. The antenna supervisor can be extended to also detect condition of open circuit by activating the ANT_DET pin and including external components for antenna open circuit detection. UBX and NMEA messages are provided to report the condition of the antenna supply. Open circuit detection can also be supported. For more information see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 8 9 For integration EVA-M8M modules with Cellular products, see the EVA-M8M Hardware Integration Manual [1]. For information on using active antennas with EVA-M8M modules, see the EVA-M8M Hardware Integration Manual [1]. UBX-160007405 - R02 Production Information Functional description Page 16 of 32 EVA-M8M - Data Sheet 2 Pin definition 2.1 Pin assignment This section shows the pin assignments. Most PIOs are configurable and have shared functions. Use special care when designing with these pins since the overall function of the device can be affected. The default configuration of the PIOs is listed in Table 7 below. For more information see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. Figure 2: Pin assignment of EVA-M8M For multiple function PIOs, select the specific signal by sending the specific configuration message or by e-fusing. UBX-160007405 - R02 Production Information Pin definition Page 17 of 32 EVA-M8M - Data Sheet Pin # Name I/O Description Remark 35 34 ANT_OFF ANT_OK O I Antenna control Antenna status Leave open if not used. Leave open if not used. 32 D_SEL I Interface selector See section1.17.6. 2 18 GND GND I I Ground Ground 37 38 GND GND I I Ground Ground Inner ground pins Inner ground pins 39 40 GND GND I I Ground Ground Inner ground pins Inner ground pins 41 42 GND GND I I Ground Ground Inner ground pins Inner ground pins 43 GND I Ground Inner ground pins 13 12 PIO13 / EXTINT PIO14 / ANT_DET I I External interrupt Antenna detection Leave open if not used. Leave open if not used. 3 4 Reserved Reserved I/O I/O Reserved Reserved Do not connect. Must be left open! Do not connect. Must be left open! 10 11 Reserved Reserved I/O I/O Reserved Reserved Do not connect. Must be left open! Do not connect. Must be left open! 17 Reserved I/O 22 SQI_D0 I/O 23 SQI_CLK I/O 24 SQI_D2 I/O 25 SQI_D1 I/O 26 SQI_CS_N I/O 27 SQI_D3 I/O 28 Reserved I/O Reserved Data line 0 to external SQI flash memory or reserved configuration pin. Clock for external SQI flash memory or configuration pin. Data line 2 to external SQI flash memory or reserved configuration pin. Data line 1 to external SQI flash memory or reserved configuration pin. Chip select for external SQI flash memory or configuration enable pin. Data line 3 to external SQI flash memory or reserved configuration pin. Reserved 33 SAFEBOOT_N I 36 Reserved 14 1 RESET_N RF_IN 8 9 15 Do not connect. Must be left open! Leave open if not used. Leave open if not used. Leave open if not used. Leave open if not used. Leave open if not used. Leave open if not used. Do not connect. Must be left open! I/O Used for programming the SQI flash memory and testing purposes. Reserved Leave open if not used. Do not connect. Must be left open! I I System reset RF Input See section 1.19. Add external LNA and SAW if no active antenna used. RTC_O O RTC Output Leave open if no RTC Crystal attached. RTC_I RXD / SPI MOSI I I RTC Input Serial interface Connect to GND if no RTC Crystal attached. See section 1.17.6. 29 30 SCL / SPI CLK SDA / SPI CS_N I I/O Serial interface Serial interface See section 1.17.6. See section 1.17.6. 31 16 TIMEPULSE TXD / SPI MISO O O Time pulse output Serial interface Leave open if not used. See section 1.17.6. 5 USB_DM I/O USB data Leave open if not used. 6 21 USB_DP V_BCKP I/O I USB data Backup supply Leave open if not used. 19 20 VCC VCC_IO I I Main supply I/O Supply 7 VDD_USB I USB Interface power Connect to GND if not used. Table 7: EVA-M8M pinout UBX-160007405 - R02 Production Information Pin definition Page 18 of 32 EVA-M8M - Data Sheet 2.2 Pin name changes Selected pin names have been updated to agree with a common naming convention across u-blox modules. The pins have not changed their operation and are the same physical hardware but with updated names. The table below lists the pins that have changed name along with their old and new names. No Previous Name New name 7 V_USB VDD_USB 15 RX / MOSI RXD / SPI MOSI 16 TX / MISO TXD / SPI MISO 26 SQI_CS SQI_CS_N 29 SCL / SCK SCL / SPI CLK 30 SDA / CS_N SDA / SPI CS_N Table 8: Pin name changes UBX-160007405 - R02 Production Information Pin definition Page 19 of 32 EVA-M8M - Data Sheet 3 Electrical specification The limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only, and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Where application information is given, it is advisory only and does not form part of the specification. For more information regarding power management see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. 3.1 Absolute maximum rating Symbol Parameter Min Max Unit VCC VCC_IO Supply voltage Supply voltage I/O ring –0.5 –0.5 3.6 3.6 V V VDD_USB V_BCKP Supply voltage USB Supply voltage baseband backup core –0.5 –0.5 3.6 3.6 V V Vi RTC Vi DIG Input voltage on RTC_I Input voltage on Configurable Inputs , RESET_N –0.5 –0.5 1.6 VCC_IO+0.5 V V Prfin RF Input power on RF_IN +15 dBm Ptot Ts Total power dissipation Storage temperature 500 +105 mW °C –40 Table 9: Absolute maximum ratings Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent damage. These are stress ratings only. The product is not protected against overvoltage or reversed voltages. If necessary, voltage spikes exceeding the power supply voltage specification, given in table above, must be limited to values within the specified boundaries by using appropriate protection diodes. UBX-160007405 - R02 Production Information Electrical specification Page 20 of 32 EVA-M8M - Data Sheet 3.2 Operating conditions The test conditions specified in Table 10 apply to all characteristics defined in this section. Symbol Parameter Min Typical Max Unit Tamb GND Ambient temperature Ground -40 +25 0 +85 °C V VCC V_BCKP Core supply voltage Backup battery supply voltage 3.3 3.3 V V VCC_IO VDD_USB Supply voltage I/O ring Supply voltage USB 3.3 3.3 V V NFtot Receiver Chain Noise Figure 5.0 dB Remarks Table 10: Test conditions All specifications are at an ambient temperature of 25°C. Extreme operating temperatures can significantly impact specification values. Applications operating near the temperature limits should be tested to ensure the specification. 3.2.1 DC electrical characteristic For Power Management Unit (PMU) block diagrams, see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. Symbol Parameter Min Typical Max Unit VCC_IO VDD_USB Supply voltage for PIOs and input voltage for LDO_B and LDO_X Supply voltage USB 1.65 3.0 3.3 3.3 3.6 3.6 V V V_BCKP VCC Input voltage for LDO_B and LDO_X (backup mode) Input voltage 1.4 1.65 3.6 3.6 V V Max Unit 0 0.2*VCC_IO nA V 0.7*VCC_IO VCC_IO+0.5 0.4 V V Table 11: Power supply pins Symbol Parameter Ileak Vil Leakage current input pins Low level input voltage Vih Vol High level input voltage Low level output voltage for TXD/SPI MISO, RXD/SPI MOSI , SDA/SPI CS_N, SCL/SPI CLK, D_SEL, TIMEPULSE, PIO13/EXTINT, PIO14/ANT_DET, ANT_OK, ANT_OFF High level output voltage for TXD/SPI MISO, RXD/SPI MOSI , SDA/SPI CS_N, SCL/SPI CLK, D_SEL, TIMEPULSE, PIO13/EXTINT, PIO14/ANT_DET, ANT_OK, ANT_OFF Pull-up resistor for SDA/SPI CS_N, SCL/SPI CLK, TIMEPULSE, PIO13/EXTINT, PIO14/ANT_DET, RESET_N Pull-up resistor for TXD/SPI MISO, RXD/SPI MOSI, D_SEL, ANT_OK, ANT_OFF Voh Rpu Rpu Condition Min Typical = 3.0 V 0 1 µA 0.8 V Vih High level input voltage VDD_USB >= 3.0 V 2.0 Vol Low level output voltage RL = 1.425 kW to VDD_USB, VDD_USB >= 3.0 V, 27 W external series resistor Voh High level output voltage RL = 14.25 kW to GND, VDD_USB >= 3.0, 27 W external series resistor Rpui Pull-up resistor, Idle State 870 900 950 W Rpuo Pull-up resistor, Operational State 1400 1490 1600 W Min. Typ. Max. Unit 0.35 0.9 sec 350 mVpp 100 kW 12 pF VDD_USB V 0.3 V 2.8 V Table 13: USB pins 3.2.2 Baseband parameters Symbol Parameter Condition RTC_Fxtal RTC crystal resonant frequency RTC_T_start RTC startup time 0.2 RTC_Amp 32768 Hz OSC oscillation amplitude 50 RTC_ESR 32768 Hz Xtal equivalent series resistance RTC_CL RTC integrated load capacitance 32768 4 ESR = 80 kW 7 Hz Table 14: Baseband parameters 3.3 Indicative power requirements Table 15 lists examples of the total system supply current for a possible application. The values in Table 15 are provided for customer information only as an example of typical current requirements. The values are characterized on samples; actual power requirements can vary depending on FW version used, external circuitry, number of SVs tracked, signal strength, type of start as well as time, duration and conditions of test. Parameter Max. supply current Symbol 10 Conditions Backup battery current 12 Typ GPS / QZSS /SBAS Iccp 12 Average supply current 11 Typ GPS & GLONASS Icc Acquisition VCC_IO = VCC = 3 V 25 19 Icc Tracking (Continuous mode) VCC_IO = VCC = 3 V 22 17 Icc Tracking (Power Save mode / 1 Hz) VCC_IO = VCC = 3 V 5.3 4.7 I_BCKP using the RTC crystal HW Backup mode, VCC_IO = VCC = 0 V 15 Max Units 67 mA mA mA mA µA 10 Use this figure to dimension maximum current capability of power supply. Measurement of this parameter with 1 Hz bandwidth. Simulated constellation of 8 satellites is used. All signals are at -130 dBm. VCC= 3 V Average current from start-up until the first fix. 12 Use this figure to determine required battery capacity. 11 12 UBX-160007405 - R02 Production Information Electrical specification Page 22 of 32 EVA-M8M - Data Sheet Parameter SW Backup current Typ Typ GPS & GLONASS GPS / QZSS /SBAS Symbol Conditions Max Units I_BCKP using the 26 MHz XTO in “single crystal” operation I_SWBCKP using the RTC crystal I_SWBCKP using the 26 MHz XTO in “single crystal” operation HW Backup mode, VCC_IO = VCC = 0 V 100 µA SW Backup mode, VCC_IO = VCC = 3 V 20 µA SW Backup mode, VCC_IO = VCC = 3 V 105 µA Table 15: Currents to calculate the indicative power requirements For more information about power requirements, see the EVA-8M / EVA-M8 Hardware Integration Manual [1]. All values in Table 15 are measured at 25°C ambient temperature. For more information on how to noticeably reduce current consumption, see the Power Management Application Note [5]. 3.4 SPI timing diagrams In order to avoid incorrect operation of the SPI, the user needs to comply with certain timing conditions. The following signals need to be considered for timing constraints: Symbol Description SPI CS_N (SS_N) Slave select signal SPI CLK (SCK) Slave clock signal Table 16: Symbol description Figure 3: SPI timing diagram UBX-160007405 - R02 Production Information Electrical specification Page 23 of 32 EVA-M8M - Data Sheet 3.4.1 Timing recommendations The SPI timing recommendations are given below. Parameter Description Recommendation tINIT Initialization Time tDES Deselect Time 10 ms 1 ms. tbit tbyte Minimum bit time Minimum byte period 180 ns (5.5 MHz max bit frequency) 8 ms (125 kHz max byte frequency) Table 17: SPI timing recommendations The values in the above table result from the requirement of an error-free transmission. By allowing just a few errors and disabling the glitch filter, the bit rate can be increased considerably. 3.5 DCC timing diagrams 2 2 The DDC interface is I C Fast Mode compliant. For timing parameters consult the I C standard. The maximum bit rate is 400 kb/s. The interface stretches the clock when slowed down when serving interrupts, so real bit rates may be slightly lower. UBX-160007405 - R02 Production Information Electrical specification Page 24 of 32 EVA-M8M - Data Sheet 4 Mechanical specification Figure 4: Mechanical drawing for EVA-M8M (LGA43) UBX-160007405 - R02 Production Information Mechanical specification Page 25 of 32 EVA-M8M - Data Sheet 5 Reliability tests and approvals 5.1 Reliability tests Qualification requirements according JEDEC standards JESD47 "Stress-Test-Driven Qualification of Integrated Circuits". 5.2 Approvals Products marked with this lead-free symbol on the product label comply with the "Directive 2002/95/EC and Directive 2011/65/EU of the European Parliament and the Council on the Restriction of Use of certain Hazardous Substances in Electrical and Electronic Equipment" (RoHS). EVA-M8M modules are RoHS compliant and green (no halogens). UBX-160007405 - R02 Production Information Reliability tests and approvals Page 26 of 32 EVA-M8M - Data Sheet 6 Product handling 6.1 Packaging EVA-M8M series modules are delivered as hermetically sealed, reeled tapes in order to enable efficient production, production lot set-up and tear-down. For more information about packaging, see the u-blox Package Information Guide [3]. 6.1.1 Reels EVA-M8M series modules are deliverable in quantities of 500 pcs on a reel. The EVA-M8M modules are shipped on Reel Type D, as described in the u-blox Package Information Guide [3]. 6.1.2 Tapes Figure 5 shows the feed direction and the orientation of the EVA-M8M positioning modules on the tape. The positioning modules are placed such that the pin 1 is at the upper right for the LGA43. The dimensions of the tapes are specified in Figure 6. Figure 5: Orientation of EVA-M8M modules on the tape Figure 6: EVA-M8M tape dimensions UBX-160007405 - R02 Production Information Product handling Page 27 of 32 EVA-M8M - Data Sheet 6.2 Moisture Sensitivity Levels The Moisture Sensitivity Level (MSL) relates to the packaging and handling precautions required. EVA-M8M modules are rated at MSL level 3. For MSL standard see IPC/JEDEC J-STD-020, which can be downloaded from www.jedec.org. For more information regarding MSL see the u-blox Package Information Guide [3]. 6.3 ESD handling precautions EVA-M8M positioning modules contain highly sensitive electronic circuitry and are Electrostatic Sensitive Devices (ESD). Observe precautions for handling! Failure to observe these precautions can result in severe damage to the GNSS receiver! GNSS receivers are Electrostatic Sensitive Devices (ESD) and require special precautions when handling. Particular care must be exercised when handling patch antennas, due to the risk of electrostatic charges. In addition to standard ESD safety practices, the following measures should be taken into account whenever handling the receiver: · Unless there is a galvanic coupling between the local GND (i.e. the work table) and the PCB GND, the first point of contact when handling the PCB must always be between the local GND and PCB GND. · Before mounting an antenna patch, connect ground of the device · When handling the RF pin, do not come into contact with any charged capacitors and be careful when contacting materials that can develop charges (e.g. patch antenna ~10pF, coax cable ~50-80 pF/m, soldering iron, …) · To prevent electrostatic discharge through the RF input, do not touch any exposed antenna area. If there is any risk that such exposed antenna area is touched in non ESD protected work area, implement proper ESD protection measures in the design. · When soldering RF connectors and patch antennas to the receiver’s RF pin, make sure to use an ESD safe soldering iron (tip). UBX-160007405 - R02 Production Information Product handling Page 28 of 32 EVA-M8M - Data Sheet 7 Default messages Interface Settings UART Output 9600 Baud, 8 bits, no parity bit, 1 stop bit Configured to transmit both NMEA and UBX protocols, but only the following NMEA (no UBX) messages have been activated at start-up: GGA, GLL, GSA, GSV, RMC, VTG, TXT Configured to transmit both NMEA and UBX protocols, but only the following NMEA (no UBX) messages have been activated at start-up: GGA, GLL, GSA, GSV, RMC, VTG, TXT USB Power Mode: Bus Powered USB Output UART Input USB Input DDC SPI TIMEPULSE ( 1 Hz Nav) 9600 Baud, 8 bits, no parity bit, 1 stop bit, Autobauding disabled Automatically accepts following protocols without need of explicit configuration: UBX, NMEA, RTCM The GNSS receiver supports interleaved UBX and NMEA messages. Automatically accepts following protocols without need of explicit configuration: UBX, NMEA, RTCM The GNSS receiver supports interleaved UBX and NMEA messages. USB Power Mode: Bus Powered Fully compatible with the I2C industry standard, available for communication with an external host CPU or u-blox cellular modules, operated in slave mode only. Default messages activated. NMEA and UBX are enabled as input messages, only NMEA as output messages. Maximum bit rate 400 kb/s. Allow communication to a host CPU, operated in slave mode only. Default messages activated. SPI is not available in the default configuration 1 pulse per second, synchronized at rising edge, pulse length 100 ms Table 18: Default messages Please refer to the u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification [2] for information about further settings. UBX-160007405 - R02 Production Information Default messages Page 29 of 32 EVA-M8M - Data Sheet 8 Labeling and ordering information 8.1 Product labeling The labeling of u-blox EVA form factor GNSS modules includes important product information. The location of the EVA-M8M product type number is shown in Figure 7. Pin 1 Marking U-BLOX EVAM8Mx10 = Product identification EVAM8M010 stands for product type number: EVA-M8M-0-10 EVAM8M110 stands for product type number: EVA-M8M-1-10 T-Rff00SS LLLLLLL YYWWZZX = Revision = Lot number = Production date code Figure 7: Description of EVA-M8M product label 8.2 Explanation of product codes Three different product code formats are used. The Product Name is used in documentation such as this data sheet and identifies all u-blox M8 products, independent of packaging and quality grade. The Ordering Code includes packaging and quality, while the Type Number includes the hardware and firmware versions. Table 19 below details these three different formats: Format Structure Product Name Ordering Code PPP-TGV-N PPP-TGV-N Type Number PPP-TGV-N-XX Table 19: Product code formats The parts of the product code are explained in Table 20. Code Meaning Example PPP TG Product Family Technology & Generation EVA M8 = u-blox M8 V N Variant Option/ Quality Grade XX Product Detail Function set (A-Z) Describes standardized functional element or quality grade 0 = Default variant, A = Automotive Describes product details or options such as hardware and software revision, cable length, etc. Table 20: Part identification code 8.3 Ordering codes Ordering No. Product EVA-M8M-0 EVA-M8M-1 u-blox M8 GNSS LGA Module, crystal, ROM, green, 7.0x7.0 mm, 500 pcs/reel (Default: GPS + GLONASS) u-blox M8 GNSS LGA Module, crystal, ROM, green, 7.0x7.0 mm, 500 pcs/reel (Default: GPS + BeiDou) Table 21: Product ordering codes for professional grade positioning modules Product changes affecting form, fit or function are documented by u-blox. For a list of Product Change Notifications (PCNs) see our website. UBX-160007405 - R02 Production Information Labeling and ordering information Page 30 of 32 EVA-M8M - Data Sheet Related documents [1] EVA-8M / EVA-M8 Hardware Integration Manual, Docu. No. UBX-16010593 [2] u-blox 8 / u-blox M8 Receiver Description Including Protocol Specification (Public version), Docu. No. UBX-13003221 [3] u-blox Package Information Guide, Docu. No. UBX-14001652 [4] [5] RTCM 10402.3 Recommended Standards for Differential GNSS, Ver. 2.3, RTCM AUG. 20, 2001 Power Management Application Note, Docu. No. UBX-13005162 [6] Radio Resource LCS Protocol (RRLP), (3GPP TS 44.031 version 11.0.0 Release 11) For regular updates to u-blox documentation and to receive product change notifications please register on our homepage. Revision history Revision Date Name Status / Comments R01 09-Jun-2016 njaf Advance Information status R02 21-Jul-2016 julu Production Information status UBX-160007405 - R02 Production Information Related documents Page 31 of 32 EVA-M8M - Data Sheet Contact For complete contact information visit us at www.u-blox.com u-blox Offices North, Central and South America u-blox America, Inc. Phone: E-mail: +1 703 483 3180 info_us@u-blox.com Regional Office West Coast: Phone: +1 408 573 3640 E-mail: info_us@u-blox.com Headquarters Europe, Middle East, Africa Asia, Australia, Pacific u-blox AG Phone: E-mail: Support: Phone: E-mail: Support: +41 44 722 74 44 info@u-blox.com support@u-blox.com Technical Support: Phone: E-mail: +1 703 483 3185 support_us@u-blox.com u-blox Singapore Pte. Ltd. +65 6734 3811 info_ap@u-blox.com support_ap@u-blox.com Regional Office Australia: Phone: +61 2 8448 2016 E-mail: info_anz@u-blox.com Support: support_ap@u-blox.com Regional Office China (Beijing): Phone: +86 10 68 133 545 E-mail: info_cn@u-blox.com Support: support_cn@u-blox.com Regional Office China (Chongqing): Phone: E-mail: Support: +86 23 6815 1588 info_cn@u-blox.com support_cn@u-blox.com Regional Office China (Shanghai): Phone: E-mail: Support: +86 21 6090 4832 info_cn@u-blox.com support_cn@u-blox.com Regional Office China (Shenzhen): Phone: +86 755 8627 1083 E-mail: info_cn@u-blox.com Support: support_cn@u-blox.com Regional Office India: Phone: +91 80 4050 9200 E-mail: info_in@u-blox.com Support: support_in@u-blox.com Regional Office Japan (Osaka): Phone: E-mail: Support: +81 6 6941 3660 info_jp@u-blox.com support_jp@u-blox.com Regional Office Japan(Tokyo): Phone: +81 3 5775 3850 E-mail: info_jp@u-blox.com Support: support_jp@u-blox.com Regional Office Korea: Phone: +82 2 542 0861 E-mail: info_kr@u-blox.com Support: support_kr@u-blox.com Regional Office Taiwan: Phone: +886 2 2657 1090 E-mail: info_tw@u-blox.com Support: support_tw@u-blox.com UBX-160007405 - R02 Production Information Contact Page 32 of 32
EVA-M8M-0-10
物料型号:EVA-M8M,是u-blox M8系列的GNSS模块,具有高度集成和灵活的连接选项。

器件简介:EVA-M8M系列模块采用u-blox M8并发定位引擎,能够接收GPS、GLONASS、Galileo、BeiDou、QZSS和SBAS信号。该模块以超紧凑的EVA封装形式提供高灵敏度和快速的捕获时间。

引脚分配:EVA-M8M模块具有43个引脚,包括电源引脚、地线、RF输入、各种通信接口(如UART、USB、SPI、DDC等)以及一些可配置的输入/输出引脚。

参数特性:EVA-M8M模块支持多频段RF前端,能够智能地使用来自三个GNSS系统(GPS和Galileo以及GLONASS或BeiDou)的最高数量的可见卫星进行可靠定位。模块还支持辅助GNSS(A-GNSS),包括AssistNow在线、离线和自主服务。

功能详解:EVA-M8M模块具备多种功能,如广播导航数据和卫星信号测量、里程表、数据记录、地理围栏、消息完整性保护、欺骗检测、外部中断、时间脉冲等。

应用信息:EVA-M8M模块适用于成本和空间敏感的应用,易于设计,通常只需要外部GNSS天线。模块的布局设计有助于减少近场干扰。

封装信息:EVA-M8M模块采用LGA43封装,适用于小型化和成本敏感的工业和可穿戴设备。
EVA-M8M-0-10 价格&库存

很抱歉,暂时无法提供与“EVA-M8M-0-10”相匹配的价格&库存,您可以联系我们找货

免费人工找货