RI-80GP0510

Group formerly RI-80GP Series Dry Reed Switch 5 mm, 1 Form A, 5 Watt RI-80GP Series Ultra-micro dry-reed switch hermetically sealed in a gas-filled glass envelope. Single-pole, single-throw (SPST) type, having normally open contacts, and containing two magnetically actuated reeds. The switch is of the double-ended type and may be actuated by an electromagnet, a permanent magnet or a combination of both. The device is intended for use in sensors, relays, pulse counters or similar devices. RI-80GP Series Features ▪ Ideal for ATE switching, proximity sensors & medical applications ▪ Contact layers: gold, sputtered ruthenium ▪ Superior glass-to-metal seal and blade alignment ▪ UL File #E125629 Dimensions for RI-80GP Series 0.91 ± 0.020 (23.0 ± 0.5) tinned 0.07 max (Ø1.8) 0.020 max (Ø0.45) 0.19 max (5.0) 1.81 ± 0.020 (46.0 ± 0.5) All Dimension in inches (mm) nominal General data for all models RI-80GP AT-Customization / Performed Leads Besides the standard models, customized products can also be supplied offering the following options: • Operate and release ranges to customer specification • Cropped and/or performed leads Coils All characteristics are measured using the Philips Standard Coil. Life expectancy and reliability The life expectancy data given below are valid for a coil energized at 1.25 times the published maximum operate value for each type in the RI-80GP series. No load conditions (operating frequency: 100Hz) Life expectancy: min. 108 operations with a failure rate of less than 2 x 10-9 with a confidence level of 90%. End of life criteria: Contact resistance > 1Ω after 2 ms Release time > 2 ms (latching or contact sticking). Rev: 0 - 10 / 2018 - BR Loaded conditions (resistive load: 5V; 100 mA; operating frequency: 170 Hz) Life expectancy: min. 107 operations with a failure rate of less than 10-8 with a confidence level of 90%. End of life criteria: Contact resistance > 2Ω after 4 ms Release time > .7 ms (latching or contact sticking) Switching different loads involves different life expectancy and reliability data. Further information available upon request. Mechanical Data Contact arrangement is normally open; lead finish is tinned; net mass is approximately 65mg; and can be mounted in any position. Shock The switches are tested in accordance with “IEC 68-2-27”, test Ea (peak acceleration 150 G, half sinewave; duration 11 ms). Such a shock will not cause an open switch (no magnetic field present) to close, nor a switch kept closed by an 80 AT coil to open. USA Tel: +(1)973 777 6900 / Fax: +(1) 973 777 8405 Page 1 of 2 RI-80GP Series Dry Reed Switch 5 mm, 1 Form A, 5 Watt Technical Specifications Parameters Test Conditions Units RI-80GP-XXXX Operating Characteristics Operate Range AT* 5-10 10-15 Release Range AT* 2-8 4-13 Operate Time - including Bounce (typ.) ms 0.35 0.35 Bounce Time (typ.) ms 0.1 0.1 Release Time (max) μs 20 20 Resonant Frequency (typ.) Hz 21300 21300 Switched Power (max) W 5 5 Switched Voltage DC (max) V 175 200 Switched Voltage AC, RMS value (max) V 140 140 Switched Current DC (max) mA 350 350 Switched Current AC, RMS value (max) Electrical Characteristics mA 250 250 Carry Current DC (max) A 0.5 0.5 Breakdown Voltage (min) V 230 230 Contact Resistance (initial max.) mΩ 160 160 Contact Resistance (initial typ.) mΩ 140 140 Contact Capacitance (max) without test coil pF 0.45 0.45 Insulation Resistance (min) RH ≤ 45% MΩ 106 106 *AT values are based on full length, measured using Philips Standard Coil (PSC). Vibration The switches are tested in accordance with “IEC 68-2-6”, test Fc (acceleration 10G; below cross-over-frequency 57 to 62 Hz; amplitude 0.75 mm; frequency range 10 to 2000 Hz; duration 90 minutes.) Such a vibration will not cause an open switch ( no magnetic field present) to close, nor a switch kept closed by an 80 AT coil to open. Mechanical Strength The robustness of the terminations is tested in accordance with “IEC 68-2-21”, test Ua1 (load 10 N). Welding The leads can be welded. Mounting The leads should not be bent closer than 1 mm to the glass-to-metal seals. Stress on the seals should be avoided Care must be taken to prevent stray magnetic fields from influencing the operating and measuring conditions. Ordering Information RI-80GP - XXXX Operating and Storage Temperature Operating ambient temperature; min: -55°C; max: +125°C. Storage temperature; min: -55°; max: +125°C. Note: Temperature excursions up to 150°C may be permissible. For more information contact your nearest Comus Group sales office. AT Ranges 0510 1015 Series Soldering The switch can withstand soldering heat in accordance with “IEC 68-2-20”, test Tb, method 1B: solder bath at 350 ± 10°C for 3.5 ± 0.5 s. Solderability is tested in accordance with “IEC 68-2-20” test Ta, method 3: solder globule temperature 235°C; ageing 1b: 4 hours steam. Rev: 0 - 10 / 2018 - BR • As part of the company policy of continued product improvement, specifications may change without notice. Our sales office will be pleased to help you with the latest information on this product range and the details of our full design and manufacturing service. All products are supplied to our standard conditions of sale unless otherwise agreed in writing. USA Tel: +(1)973 777 6900 / Fax: +(1) 973 777 8405 Page 2 of 2