深圳市首韩科技有限公司
SHENZHEN SHOUHAN TECHNOLOGYCO.,LTD
Tel: 0755-27597601 Fax: 0755-27597491
承
认
书
产品名称 Project:
针座
科
规格型号 Part No:
有
户 Customer:
技
客
限
公
司
SPECIFICATION FOR APPROVAL
韩
1.25mm LT( 立贴) 位数通用
首
贵公司承认印 Approal slgnatures
签
章/Signatures
深
圳
市
料 号/Part No.
日期 Date:
拟制/Drawn
李春风
审核/Check
钟华华
批准/Approved
罗孝金
深圳市首韩科技有限公司
产品名称
Product Name
针座
产品型号
Product Model
1.25mm LT( 立贴) 位数通用
页
码
Page Number
第 1 页/共 5 页
产 品 承 认 书
SPECIFICATION FOR APPROVAL
1. 构造成:Cons truction
形状、尺寸依照附图规定
Shape and dimensions subject toattached chart regul atoin
2. 线束:Poles
2~16
3. 适用线规:Applicable Wires
AWG#32~#28
4. 适用温度范围:Ambient temperature Range
-40℃~+85℃
5. 适用基板厚度:Applicable PC board thickness
0.6~1.2mm
6. 额定电压:Voltage rating
200V.AC/DC
7. 额定电流:Current rating
1.0A Max
8. 环保:Environmental protection
本产品符合 ROHS 环保要求
RoHS compliant and customer’s environment protection request compliant
9. 材料:Material
基座 (Wafer)
:L C P
:磷青铜 Phosphor bronze
插针 (Pin)
焊片 (Solder tab) : 磷青铜 Phosphor bronze
10.包装 Packaging
产品内包装为连带,外包装为纸箱,产品在箱内密封,不晃动
Unless otherwise specified,the series connectors are packed with Taping specifications
11.运输 Transportation
允许用任何方式运输,但需避免雨雪淋和阳光照射,不能有碰撞和挤压等机械损伤,运输环境温度为-20℃~+50℃
Any vehicle can be adopted for the transportation,but inoistrre-proof and no mechanical
damage,transport temperature to -20℃~+50℃
12. 贮存: Store up
包装完毕的连接器应在坏境温度为-20℃~+50℃,相对湿度不大于 80%,周围空气中没有酸性、碱性及其它腐蚀性气
体的仓库中贮存。
Temperature: -20℃~+50℃
Relative Humidity:<80%
No to storage in corrosive environments
13. 产品性能要求: Performance
深圳市首韩科技有限公司
产品名称
Product Name
针座
产品型号
Product Model
1.25mm LT( 立贴) 位数通用
页
码
Page Number
第 2 页/共 5 页
产 品 承 认 书
SPECIFICATION FOR APPROVAL
序号
项目 Item
测试条件 Test Condition
规格要求 Requirement
1. 塑料件表面应无明显疤痕、杂色、开裂、毛
1
外 观
Appearance
接触电阻
2
Contact
Resistance
目测
刺、飞边、缺料及影响使用的变形
Visual by eye
视力:1.0 以上
Light:>1.0
照明:(200~300)lx
Lamp: (200~300)lx
目测距离:(0.3~0.5)m
Space:(0.3~0.5)m
Plastic part:smooth and flat surface without
discolor,broken,crack,distortion defects
is acceptable
2. 金属件表面应光洁,无锈蚀、氧化、脱皮、
发黑及明显的机械损伤等缺陷
Metal part:bright and even surface without
rust,oxide,fog and obvious physical damage
defects is acceptable
插配阴阳连接器后,用小功率电阻
测试仪进行测试
Mate connectors,measure by dry
circuit
≤0.03Ω
插配阴阳连接器后,在相邻接触件
绝缘电阻
3
Insulation
Resistance
之间或地线之间,用 250V DC 电压
进行测试
Mate connectors,apple 250V
DC between ad jacent terminal or
ground
≥1000MΩ
相邻接触件之间或地线之间施加
耐电压
4
Withstand
voltage
插入力与拔出力
5
Insertion and
Withdrawal
Force
50Hz1000V AC (有效值),漏电
流1mA 的电压作用,时间 1 分钟.
Mate connectors,apply 1000V
AC for 1min between ad
jacent terminal or ground
无击穿和飞弧现象
No Breakdown
相配的连接器以 1mm/s~5mm/s 的
速度沿接插器轴线方向插入和拔出
插入力(最大值)
拔出力(最小值)
Insertion and withdrawal
connectors at the speed rate
of 1mm/s~5mm/s
Insertion(MAX)
Withdrawal(MIN)
<6.0N*接触件数
>1.0N*接触件数
深圳市首韩科技有限公司
产品名称
Product Name
针座
产品型号
Product Model
1.25mm LT( 立贴) 位数通用
页
码
Page Number
第 3 页/共 5 页
产 品 承 认 书
SPECIFICATION FOR APPROVAL
序号
项目 Item
测试条件 Test Condition
规格要求 Requirement
固定连接器端在测力计上,在连
端子在塑件
6
中的保持力(不适用)
Terminal/Housing
Retention Force
接器轴线方向施加规定的拉力,
速度不大于 25mm/分钟
Apply axial pull out force at the
speed rate of not more 25mm/min
on the pin assemble in the
housing
≥5N
在试验装置夹头中固定试验样
压着部位的
7
抗张强度(不适用)
Crimping pull
Out Force
品,在连接器的轴线方向施加张
力;速度不大于 25mm/分钟
28# :10N (Min)
30# :8N (Min)
32# :6N (Min)
Fix the crimped terminal,apply
axial pull out force on the wire
at the speed rate of not more
25mm/min
将针座放在插拔机上,以每分钟
25±5mm 的速度垂直把针推出针
针固定力
8
Pin retentive
Force
座
Putting the wafer on the
force tester and push the pins
out vertically at the speed rate
of 25±5mm per minutes
把试件放入高温试验箱中,以
耐高温
9
Heat
Resistance
10
Cold Resistance
外观
℃/min 的温度变化速度,
(0.7~1)
Appearance
将温度调到(85±2)℃。待平衡
后保持 4h,然后以同样的速度降
接触电阻
到温室,恢复 2h 检验
Contact Resistance
(85±2)℃,4h
把试件放入低温试验箱中,以
耐寒性
≥3N
(0.7~1)℃/min 的温度变化速
度,将温度调到(-40±2)℃。待
平衡后保持 4h,然后以同样的速
度升到室温,恢复 2h 检查
(-40±2)℃,4h
无损伤
No Damage
≤0.02Ω
外观
无损伤
Appearance
No Damage
接触电阻
Contact Resistance
≤0.02Ω
深圳市首韩科技有限公司
产品名称
Product Name
针座
产品型号
Product Model
1.25mm LT( 立贴) 位数通用
页
码
Page Number
第 4 页/共 5 页
产 品 承 认 书
SPECIFICATION FOR APPROVAL
序号
项目 Item
测试条件 Test Condition
规格要求 Requirement
把试验样品分别放入高、低温试验
箱,按下列步骤调试温度:
a) 在(-40±2)℃的恒温条件下
放置 2 小时;
温度循环
11
Temperature
Cycling
b)
在常温条件下放置 1 小时;
c)
在(85±2)℃的恒温条件下放
外观
无损伤
Appearance
No Damage
置 2 小时;
d)
在常温条件下放置 1 小时
从 a)到 d)为一个循环周期,共进
行 5 个循环,恢复 2 小时检查
5 cycles of:
a) (-40±2)℃ 2h
b) (85±2)℃ 2h
温度上升
12
Temperature
Rise
Contact Resistance
插合连接器,通以最大容许电流
温度上升
Carrying rated current load
Temperature Rise
温度(40±2)℃,
相对湿度(90~95)%
13
接触电阻
恒定湿热
放置 96 小时, 取出恢复 2 小时后
Humindity
检查
Temperature(40±2)℃
Relative Humidity:(90~95)%
Duration 96h
插合连接器,串联在一直电流电源
上,电流 1mA;并模拟正常工作状
≤0.02Ω
≤30℃
外观
无损伤
Appearance
No Damage
耐电压
Withstand voltage
绝缘电阻
Insulation Resistance
250V,AC/min
≥100MΩ
外观
无损伤
Appearance
No Damage
态,振频为 (10~55)Hz 、振幅
耐振动性
14
Vibration
Resistance
0.35mm;(55~500)Hz 、 加 速 度
50m/s2. 每 一 轴 线 扫 频 循 环 次 数
接触电阻
Contact Resistance
≤0.02Ω
10 次、历时 2 小时
Amplitude:±0.35mm
Frequency:(10~55)Hz
Frequency:(>55~500)Hz
Acceleration:50m/s2
Duration:2h in each X、Y、Z axes
瞬断
Discontinuity
≤1μS
深圳市首韩科技有限公司
产品名称
Product Name
针座
产品型号
Product Model
1.25mm LT( 立贴) 位数通用
页
码
Page Number
第 5 页/共 5 页
产 品 承 认 书
SPECIFICATION FOR APPROVAL
序号
项目 Item
机械寿命
15
16
Repeated
Insertion/
withdrawal
盐雾测试
Salt Spray Test
测试条件 Test Condition
规格要求 Requirement
无通电状态下,10 次/分钟的速度
插拔 50 次
When mated up to 50 cycles
repeatedly by the rate of
10 cycles per minute
接触电阻
Contact Resistance
≤0.02Ω
把试验样品从试验箱顶悬挂下来,
无损伤、腐蚀(五金件
%的氯化钠溶液,
采用浓度为(5±1)
应无露出底金属的严
连续雾化 24h,试验后用流动的蒸
馏水轻轻洗去表面沉淀积物。在常
温条件下恢复 1~2 小时。
外观
Appearance
24 h exposure to a saltspray from
the(5±1)% solution
重锈蚀;使用预镀好的
型材,其落料面允许有
不影响其性能的轻微
腐蚀。)
No Damage
把试验样品需要焊接的部位浸入
17
可焊性
Solderability
耐焊接热
18
235±5 ℃的 锡 槽 中 : 历 时 2 ±
0.5sec
Soldering Time: 2±0.5 sec
Soldering Temperature:235±5℃
沾敷性
沾敷面积
Solder wetting
95%以上
外观
无损坏,变形
Appearance
No Damage
把试验样品需要焊接的部分浸入
260±5℃的锡炉中:历时 5±1sec
Resistance to
Soldering Time: 5±1sec
Soldering heat
Soldering Temperature: 260±5℃
Note:以上测试视公司之测试条件/能力而定。
⒊
PCB寸法
PCB Layout
⒉
⒈
1.25mm LT( 立贴) 位数通用
技术指标:
1、塑件表面应光洁、无毛刺、明显收缩、缺陷、裂纹等现象
2、温度范围:-25%%D~85°;
3、额定电压:200v,AC,DC(等效);
4、接触电阻:≤0.03;
5、绝缘电阻:≥1000M
6、耐压:1000v,AC/minute.
2
3
4
5
6
7
8
10
11
12
13
14
15
16
深圳市首韩科技有限公司
李春风
钟华华
罗孝金
很抱歉,暂时无法提供与“1.25-7P LT”相匹配的价格&库存,您可以联系我们找货
免费人工找货- 国内价格
- 1+0.23120
- 30+0.22270
- 100+0.21420
- 500+0.19720
- 1000+0.18870
- 2000+0.18360