S-8254A Series
www.ablic.com
www.ablicinc.com
BATTERY PROTECTION IC
FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
© ABLIC Inc., 2002-2016
Rev.5.2_01
The S-8254A Series is a protection IC for 3-serial- or 4-serial-cell lithium-ion / lithium polymer rechargeable
batteries and includes a high-accuracy voltage detector and delay circuit.
The S-8254A Series protects both 3-serial or 4-serial cells using the SEL pin for switching.
Features
(1) High-accuracy voltage detection for each cell
Overcharge detection voltage n (n 1 to 4)
3.9 V to 4.4 V (50 mV step)
Accuracy 25 mV
Accuracy 50 mV
Overcharge release voltage n (n 1 to 4)
3.8 V to 4.4 V*1
Overdischarge detection voltage n (n 1 to 4) 2.0 V to 3.0 V (100 mV step)
Accuracy 80 mV
Accuracy 100 mV
Overdischarge release voltage n (n 1 to 4)
2.0 V to 3.4 V*2
(2) Three-level overcurrent protection
Overcurrent detection voltage 1
0.05 V to 0.30 V (50 mV step) Accuracy 25 mV
Overcurrent detection voltage 2
0.5 V
Accuracy 100 mV
Accuracy 300 mV
Overcurrent detection voltage 3
VVC1 1.2 V
(3) Delay times for overcharge detection, overdischarge detection and overcurrent detection 1 can be set
by external capacitors (delay times for overcurrent detection 2 and 3 are fixed internally).
(4) Switchable between a 3-serial cell and 4-serial cell using the SEL pin
(5) Charge/discharge operation can be controlled via the control pins.
(6) High-withstand voltage
Absolute maximum rating : 26 V
(7) Wide operating voltage range
2 V to 24 V
(8) Wide operating temperature range 40C to 85C
(9) Low current consumption
During operation
30 A max. (25C)
During power-down
0.1 A max. (25C)
*3
(10) Lead-free, Sn100%, halogen-free
*1. Overcharge hysteresis voltage n (n 1 to 4) can be selected as 0 V or from a range of 0.1 V to 0.4 V in
50 mV steps.
(Overcharge hysteresis voltage Overcharge detection voltage Overcharge release voltage)
*2. Overdischarge hysteresis voltage n (n 1 to 4) can be selected as 0 V or from a range of 0.2 V to 0.7 V
in 100 mV steps.
(Overdischarge hysteresis voltage Overdischarge release voltage Overdischarge detection voltage)
*3. Refer to “ Product Name Structure” for details.
Applications
Lithium-ion rechargeable battery packs
Lithium polymer rechargeable battery packs
Package
16-Pin TSSOP
1
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Block Diagram
COP
DOP, COP,
RVMD, RVMS
Control Circuit
VDD
Delay Circuit
VC1
Delay Circuit
Delay Circuit
1 M
VMP
Delay Circuit
900 k
VC2
VC3
DOP
VINI
VC4
CDT
200 nA
CCT
CTL
VSS
Remark
SEL
1. Diodes in the figure are parasitic diodes.
2. Numerical values are typical values.
Figure 1
2
Rev.5.2_01
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Product Name Structure
1. Product Name
S-8254A
xx
FT
-
TB
-
x
Environmental code
U: Lead-free (Sn 100%), halogen-free
S: Lead-free, halogen-free
G: Lead-free (for details, please
contact our sales office)
IC direction in tape specifications *1
Package code
FT: 16-Pin TSSOP
Serial code *2
Sequentially set from AA to ZZ
*1. Refer to the tape drawing.
*2. Refer to “3. Product Name List”.
2. Package
Package name
16-Pin TSSOP
Environmental code = G, S
Environmental code = U
Package
Tape
Reel
FT016-A-P-SD
FT016-A-P-SD
FT016-A-C-SD
FT016-A-C-SD
FT016-A-R-SD
FT016-A-R-S1
3
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
3. Product Name List
Table 1
Overcharge
Overcharge
Overdischarge
Overdischarge
Overcurrent
0 V battery
detection voltage release voltage detection voltage release voltage detection voltage 1
charge function
[VCU]
[VCL]
[VDL]
[VDU]
[VIOV1]
Available
S-8254AAAFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.00 0.080 V 2.70 0.100 V
0.30 0.025 V
Available
S-8254AABFT-TB-x 4.250 0.025 V 4.250 0.025 V 2.00 0.080 V 2.70 0.100 V
0.30 0.025 V
Available
S-8254AAEFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.00 0.080 V 2.70 0.100 V
0.20 0.025 V
Available
S-8254AAFFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.40 0.080 V 3.00 0.100 V
0.20 0.025 V
Available
S-8254AAGFT-TB-x 4.275 0.025 V 4.075 0.050 V 2.30 0.080 V 2.70 0.100 V
0.13 0.025 V
Available
S-8254AAHFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.40 0.080 V 2.70 0.100 V
0.10 0.025 V
Available
S-8254AAIFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.40 0.080 V 3.00 0.100 V
0.30 0.025 V
Available
S-8254AAJFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.40 0.080 V 3.00 0.100 V
0.15 0.025 V
Available
S-8254AAKFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.70 0.080 V 3.00 0.100 V
0.20 0.025 V
Available
S-8254AALFT-TB-x 4.300 0.025 V 4.150 0.050 V 2.40 0.080 V 3.00 0.100 V
0.20 0.025 V
Available
S-8254AAMFT-TB-x 4.200 0.025 V 4.100 0.050 V 2.50 0.080 V 2.70 0.100 V
0.30 0.025 V
Available
S-8254AANFT-TB-x 4.250 0.025 V 4.150 0.050 V 2.50 0.080 V 3.00 0.100 V
0.10 0.025 V
Available
S-8254AAOFT-TB-x 4.300 0.025 V 4.080 0.050 V 2.50 0.080 V 3.00 0.100 V
0.10 0.025 V
Available
S-8254AAPFT-TB-x 4.280 0.025 V 4.130 0.050 V 3.00 0.080 V 3.00 0.080 V
0.15 0.025 V
Available
S-8254AAQFT-TB-x 3.900 0.025 V 3.800 0.050 V 2.30 0.080 V 2.70 0.100 V
0.30 0.025 V
Available
S-8254AARFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.80 0.080 V 3.00 0.100 V
0.20 0.025 V
Available
S-8254AASFT-TB-x 4.290 0.025 V 4.090 0.050 V 2.30 0.080 V 3.00 0.100 V
0.075 0.025 V
Available
S-8254AATFT-TB-x 4.200 0.025 V 4.200 0.025 V 2.00 0.080 V 2.70 0.100 V
0.30 0.025 V
Unavailable
S-8254AAUFT-TB-x 4.350 0.025 V 4.150 0.050 V 2.40 0.080 V 3.00 0.100 V
0.20 0.025 V
Available
S-8254AAVFT-TB-x 4.250 0.025 V 4.150 0.050 V 2.70 0.080 V 3.00 0.100 V
0.20 0.025 V
Unavailable
S-8254AAWFT-TB-x 4.250 0.025 V 4.100 0.050 V 3.00 0.080 V 3.20 0.100 V
0.10 0.025 V
Available
S-8254AAXFT-TB-x 4.250 0.025 V 4.100 0.050 V 2.00 0.080 V 2.70 0.100 V
0.15 0.025 V
Available
S-8254AAYFT-TB-x 4.275 0.025 V 4.125 0.050 V 2.40 0.080 V 2.70 0.100 V
0.10 0.025 V
Available
S-8254AAZFT-TB-x 4.250 0.025 V 4.150 0.050 V 2.00 0.080 V 2.70 0.100 V
0.13 0.025 V
Available
S-8254ABAFT-TB-x 3.900 0.025 V 3.800 0.050 V 2.00 0.080 V 2.50 0.100 V
0.15 0.025 V
Available
S-8254ABBFT-TB-x 4.200 0.025 V 4.200 0.025 V 2.50 0.080 V 3.20 0.100 V
0.30 0.025 V
Available
S-8254ABCFT-TB-x 4.175 0.025 V 3.975 0.050 V 2.75 0.080 V 3.05 0.100 V
0.10 0.025 V
Available
S-8254ABDFT-TB-y 4.300 0.025 V 4.100 0.050 V 2.00 0.080 V 2.00 0.080 V
0.13 0.025 V
Available
S-8254ABEFT-TB-y 4.200 0.025 V 4.150 0.050 V 2.50 0.080 V 3.00 0.100 V
0.15 0.025 V
Available
S-8254ABFFT-TB-x 4.150 0.025 V 4.050 0.050 V 2.00 0.080 V 2.70 0.100 V
0.13 0.025 V
Available
S-8254ABGFT-TB-x 4.180 0.025 V 4.080 0.050 V 2.00 0.080 V 2.70 0.100 V
0.13 0.025 V
Available
S-8254ABHFT-TB-y 4.150 0.025 V 4.050 0.050 V 2.50 0.080 V 2.80 0.100 V
0.10 0.025 V
Unavailable
S-8254ABIFT-TB-x 4.215 0.025 V 4.115 0.050 V 2.40 0.080 V 3.00 0.100 V
0.20 0.025 V
Remark 1. Please contact our sales office for the products with the detection voltage value other than those
specified above.
2. x: G or U
y: S or U
3. Please select products of environmental code = U for Sn 100%, halogen-free products.
Product name /
Item
4
Rev.5.2_01
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Pin Configuration
16-Pin TSSOP
Top view
COP
1
16
VDD
VMP
2
15
VC1
DOP
3
14
VC2
VINI
4
13
VC3
CDT
5
12
VC4
CCT
6
11
CTL
VSS
7
10
SEL
NC
8
9
NC
Figure 2
Table 2
Pin No.
1
Symbol
COP
Description
FET gate connection pin for charge control (Nch open drain output)
Pin for voltage detection between VC1 and VMP (Pin for overcurrent 3
2
VMP
detection)
3
DOP
FET gate connection pin for discharge control FET (CMOS output)
Pin for voltage detection between VSS and VINI (Pin for overcurrent detection
4
VINI
1,2)
Capacitor connection pin for delay for overdischarge detection, delay for
5
CDT
overcurrent detection 1
6
CCT
Capacitor connection pin for delay for overcharge current
Input pin for negative power supply,
7
VSS
Connection pin for battery 4’s negative voltage
8
NC *1
No connection
9
NC *1
No connection
Pin for switching 3-series or 4-series cell
10
SEL
VSS level: 3-series cell, VDD level : 4-series cell
11
CTL
Control of charge FET and discharge FET
Connection pin for battery 3’s negative voltage,
12
VC4
Connection pin for battery 4’s positive voltage
Connection pin for battery 2’s negative voltage,
13
VC3
Connection pin for battery 3’s positive voltage
Connection pin for battery 1’s negative voltage,
14
VC2
Connection pin for battery 2’s positive voltage
15
VC1
Connection pin for battery 1’s positive voltage
Input pin for positive power supply,
16
VDD
Connection pin for battery 1’s positive voltage
*1. The NC pin is electrically open. The NC pin can be connected to VDD or VSS.
5
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Absolute Maximum Ratings
Table 3
Item
Symbol
Input voltage between VDD and VSS
VDS
Input pin voltage
VIN
VMP pin input voltage
DOP pin output voltage
COP pin output voltage
VVMP
VDOP
VCOP
Power dissipation
PD
Applied pin
VC1, VC2, VC3,
VC4, CTL, SEL,
CCT, CDT, VINI
VMP
DOP
COP
Operating ambient temperature
Topr
Storage temperature
Tstg
*1. When mounted on board
[Mounted board]
(1) Board size : 114.3 mm 76.2 mm t1.6 mm
(2) Board name : JEDEC STANDARD51-7
(Ta 25C unless otherwise specified)
Absolute Maximum Ratings
Unit
V
VSS 0.3 to VSS 26
VSS 0.3 to VDD 0.3
V
VSS 0.3 to VSS 26
VSS 0.3 to VDD 0.3
VSS 0.3 to VSS 26
400 (When not mounted on board)
1100*1
40 to 85
40 to 125
V
V
V
mW
mW
C
C
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
Power Dissipation (PD) [mW]
1200
1000
800
600
400
200
0
0
50
100
150
Ambient Temperature (Ta) [C]
Figure 3 Power Dissipation of Package (When Mounted on Board)
6
Rev.5.2_01
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Electrical Characteristics
Table 4 (1 / 2)
Item
Symbol
[ DETECTION VOLTAGE ]
Overcharge detection voltage n
(n 1, 2, 3, 4)
Overcharge release voltage n
(n 1, 2, 3, 4)
Overdischarge detection voltage n
(n 1, 2, 3, 4)
Overdischarge release voltage n
(n 1, 2, 3, 4)
VCUn
VCLn
VDLn
VDUn
Conditions
VCUn
0.025
VCLn
0.05
VCLn
0.025
VDLn
0.08
VDUn
0.10
VDUn
0.08
VIOV1
0.025
0.4
VVC1
1.5
1.0
0.5
CCT pin capacitance 0.1 F
0.5
VVC1
1.2
0
0
VCUn
0.025
VCLn
0.05
VCLn
0.025
VDLn
0.08
VDUn
0.10
VDUn
0.08
VIOV1
0.025
0.6
VVC1
0.9
1.0
0.5
0.5
1.0
CDT pin capacitance 0.1 F
50
CDT pin capacitance 0.1 F
V
2
V
2
V
2
V
2
V
2
V
2
V
2
V
2
V
2
mV / °C
mV / °C
2
2
1.5
s
3
100
150
ms
3
5
10
15
ms
3
0.4
1
1.6
ms
3
FET gate capacitance 2000 pF
100
300
600
s
3
0 V battery charging available
0.8
1.5
V
4
0 V battery charging unavailable
0.4
0.7
1.1
V
4
0.5
1
1.5
M
5
450
900
1800
k
5
3.9 V to 4.4 V, Adjustable
VCL VCU
3.8 V to 4.4 V,
Adjustable
VCL VCU
2.0 V to 3.0 V, Adjustable
VDL VDU
2.0 V to 3.4 V,
Adjustable
VDL VDU
Overcurrent detection voltage 1
VIOV1
Overcurrent detection voltage 2
VIOV2
Overcurrent detection voltage 3
VIOV3
*1
Temperature coefficient 1
TCOE1
*2
Temperature coefficient 2
TCOE2
[ DELAY TIME ]
Overcharge detection delay time
tCU
Overdischarge detection
tDL
delay time
Overcurrent detection
tIOV1
delay time 1
Overcurrent detection
tIOV2
delay time 2
Overcurrent detection
tIOV3
delay time 3
[ 0 V BATTERY CHARGE FUNCTION ]
0 V battery charge
V0CHA
starting charger voltage
0 V battery charge
V0INH
inhibition battery voltage
[ INTERNAL RESISTANCE ]
Resistance between
RVMD
VMP and VDD
Resistance between
RVMS
VMP and VSS
(Ta 25C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
circuit
0.05 V to 0.3 V, Adjustable
*3
Ta 0°C to 50°C
*3
Ta 0°C to 50°C
VCUn
VCLn
VCLn
VDLn
VDUn
VDUn
VIOV1
7
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Table 4 (2 / 2)
Item
[ INPUT VOLTAGE ]
Operating voltage between VDD
and VSS
Symbol
VDSOP
Conditions
Output voltage of DOP and
COP fixed
Rev.5.2_01
(Ta 25C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
circuit
2
24
V
2
CTL input voltage “H”
VCTLH
VDD
0.8
V
2
CTL input voltage “L”
VCTLL
VDD
0.2
V
2
SEL input voltage “H”
VSELH
VDD
0.8
V
2
SEL input voltage “L”
VSELL
VDD
0.2
V
2
[ INPUT CURRENT ]
Current consumption
during operation
Current consumption
during power-down
VC1 pin current
VC2 pin current
VC3 pin current
VC4 pin current
IOPE
V1 V2 V3 V4 3.5 V
12
30
A
1
IPDN
V1 V2 V3 V4 1.5 V
0.1
A
1
IVC1
IVC2
IVC3
IVC4
V1 V2 V3 V4 3.5 V
V1 V2 V3 V4 3.5 V
V1 V2 V3 V4 3.5 V
V1 V2 V3 V4 3.5 V
V1 V2 V3 V4 3.5 V,
VCTL VDD
V1 V2 V3 V4 3.5 V,
VCTL VSS
V1 V2 V3 V4 3.5 V,
VSEL VDD
V1 V2 V3 V4 3.5 V,
VSEL VSS
0.3
0.3
0.3
1.5
0
0
0
3
0.3
0.3
0.3
A
A
A
A
5
5
5
5
0.1
A
5
0.4
0.2
A
5
0.1
A
5
0.1
A
5
CTL pin current “H”
ICTLH
CTL pin current “L”
ICTLL
SEL pin current “H”
ISELH
SEL pin current “L”
ISELL
[ OUTPUT CURRENT ]
COP pin leakage current
ICOH VCOP 24 V
0.1
5
A
10
COP pin sink current
ICOL
5
A
VCOP VSS 0.5 V
10
DOP pin source current
IDOH VDOP VDD 0.5 V
5
A
10
DOP pin sink current
IDOL
5
A
VDOP VSS 0.5 V
*1. Voltage temperature coefficient 1 : Overcharge detection voltage
*2. Voltage temperature coefficient 2 : Overcurrent detection voltage 1
*3. Since products are not screened at high and low temperature, the specification for this temperature range is
guaranteed by design, not tested in production.
8
Rev.5.2_01
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Test Circuits
This chapter describes how to test the S-8254A Series when a 4-serial cell is selected by setting the SEL pin
to the VDD level. When a 3-serial cell is selected by setting the SEL pin to the VSS level, short the power
supply V4.
1. Current Consumption during Operation, Current Consumption during Power-down
(Test circuit 1)
1. 1 Current Consumption during operation (IOPE)
The current at the VSS pin when V1 V2 V3 V4 3.5 V and VVMP VDD is the current
consumption during operation (IOPE).
1. 2 Current Consumption during power-down (IPDN)
The current at the VSS pin when V1 V2 V3 V4 1.5 V and VVMP VSS is the current consumption
during power-down (IPDN).
2. Overcharge Detection Voltage, Overcharge Release Voltage, Overdischarge Detection Voltage,
Overdischarge Release Voltage, Overcurrent Detection Voltage 1, Overcurrent Detection Voltage
2, Overcurrent Detection Voltage 3, CTL Input Voltage “H”, CTL Input Voltage “L”, SEL Input
Voltage “H”, SEL Input Voltage “L”
(Test circuit 2)
Confirm that the COP pin and DOP pin are low (VDD 0.1 V or lower) when VVMP VSEL VDD, VINI
VCTL VSS, the CCT pin is open, the CDT pin is open, and V1 V2 V3 V4 3.5 V (this status is
referred to as the initial status).
2. 1 Overcharge Detection Voltage (VCU1), Overcharge Release Voltage (VCL1)
The overcharge detection voltage (VCU1) is the voltage of V1 when the voltage of the COP pin is “H”
(VDD 0.9 V or more) after the V1 voltage has been gradually increased starting at the initial status.
The overcharge release voltage (VCL1) is the voltage of V1 when the voltage at the COP pin is “L” after
the V1 voltage has been gradually decreased.
2. 2 Overdischarge Detection Voltage (VDL1), Overdischarge Release Voltage (VDU1)
The overdischarge detection voltage (VDL1) is the voltage of V1 when the voltage of the DOP pin is “H”
after the V1 voltage has been gradually decreased starting at the initial status. The overdischarge
release voltage (VDU1) is the voltage of V1 when the voltage at the DOP pin is “L” after the V1 voltage
has been gradually increased.
When the voltage of Vn (n 2 to 4) is changed, the overcharge detection voltage (VCUn), overcharge
release voltage (VCLn), overdischarge detection voltage (VDLn), and overdischarge release voltage
(VDUn) can be determined in the same way as when n 1.
2. 3 Overcurrent Detection Voltage 1 (VIOV1)
Overcurrent detection voltage 1 (VIOV1) is the voltage of the VINI pin when the voltage of the DOP pin
is “H” after the VINI pin voltage has been gradually increased starting at the initial status.
2. 4 Overcurrent Detection Voltage 2 (VIOV2)
Overcurrent detection voltage 2 (VIOV2) is the voltage of the VINI pin when the voltage of the DOP pin
is “H” after the voltage of the CDT pin was set to VSS following the initial status and the voltage of the
VINI pin has been gradually decreased.
2. 5 Overcurrent Detection Voltage 3 (VIOV3)
Overcurrent detection voltage 3 (VIOV3) is the voltage difference between VVC1 and VVMP (VVC1 VVMP)
when the voltage of the DOP pin is “H” after the VMP voltage has been gradually decreased starting at
the initial status.
9
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
2. 6 CTL Input Voltage “H” (VCTLH), CTL Input Voltage “L” (VCTLL)
The CTL input voltage “H” (VCTLH) is the voltage of CTL when the voltages at the COP and DOP pins
are “H” after the CTL voltage has been gradually increased starting at the initial status. The CTL input
voltage “L” (VCTLL) is the voltage of CTL when the voltages at the COP and DOP pins are “L” after the
CTL voltage has been gradually decreased.
2. 7 SEL Input Voltage “H” (VSELH), SEL Input Voltage “L” (VSELL)
Apply 0 V to V4 in the initial status and confirm that the DOP pin is “H”. The SEL input voltage “L”
(VSELL) is the voltage of the SEL pin when the voltage at the DOP pin is “L” after the SEL voltage has
been gradually decreased. The SEL input voltage “H” (VSELH) is the voltage of the SEL pin when the
voltage of the DOP pin is “H” after the SEL voltage has been gradually increased.
3. Overcharge Detection Delay Time, Overdischarge Detection Delay Time, Overcurrent Detection
Delay Time 1, Overcurrent Detection Delay Time 2, Overcurrent Detection Delay Time 3
(Test circuit 3)
Confirm that the COP pin and DOP pin are “L” when VVMP VDD, VINI VSS, and V1 V2 V3 V4
3.5 V (this status is referred to as the initial status).
3. 1 Overcharge Detection Delay Time (tCU)
The overcharge detection delay time (tCU) is the time it takes for the voltage of the COP pin to change
from “L” to “H” after the voltage of V1 is instantaneously changed to 4.5 V from the initial status.
3. 2 Overdischarge Detection Delay Time (tDL)
The overdischarge detection delay time (tDL) is the time it takes for the voltage of the DOP pin to
change from “L” to “H” after the voltage of V1 is instantaneously changed to 1.5 V from the initial
status
3. 3 Overcurrent Detection Delay Time 1 (tIOV1)
Overcurrent detection delay time 1 (tIOV1) is the time it takes for the voltage of the DOP pin to change
from “L” to “H” after the voltage of the VINI pin is instantaneously changed to 0.4 V from the initial
status.
3. 4 Overcurrent Detection Delay Time 2 (tIOV2)
Overcurrent detection delay time 2 (tIOV2) is the time it takes for the voltage of the DOP pin to change
from “L” to “H” after the voltage of the VINI pin is instantaneously changed to VIOV2 max. 0.2 V from
the initial status.
3. 5 Overcurrent Detection Delay Time 3 (tIOV3)
Overcurrent detection delay time 3 (tIOV3) is the time it takes for the voltage of the DOP pin to change
from “L” to “H” after the voltage of the VMP pin is instantaneously changed to VIOV3 min. 0.2 V from
the initial status.
10
Rev.5.2_01
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
4. 0 V Battery Charge Starting Charger Voltage (Product with 0 V Battery Charge Function), 0 V
Battery Charge Inhibition Battery Voltage (Product with 0 V Battery Charge Inhibition Function)
(Test circuit 4)
Either the 0 V battery charge starting charger voltage or the 0 V battery charge inhibition battery voltage
is applied to each product according to the 0 V battery charge function.
4. 1
0 V Battery Charge Starting Charger Voltage (V0CHA) (Product with 0 V Battery Charge
Function)
The starting condition is V1 V2 V3 V4 0 V for a product in which 0 V battery charging is
available. The COP pin voltage should be lower than V0CHA max. 1 V when the VMP pin voltage
VVMP V0CHA max.
4. 2
0 V Battery Charge Inhibition Battery Voltage (V0INH) (Product with 0 V Battery Charge
Inhibition Function)
The starting condition is V1 V2 V3 V4 V0INH for a product in which 0 V battery charging is
inhibited. The COP pin voltage should be higher than VVMP 1 V when the VMP pin voltage VVMP
24 V.
5. Resistance between VMP and VDD, Resistance between VMP and VSS, VC1 Pin Current, VC2 Pin
Current, VC3 Pin Current, VC4 Pin Current, CTL pin Current “H”, CTL Pin Current “L”, SEL Pin
Current “H”, SEL Pin Current “L”, COP Pin Leakage Current, COP Pin Sink Current, DOP Pin
Source Current, DOP Pin Sink Current
(Test circuit 5)
VVMP VSEL VDD, VINI VCTL VSS, V1 V2 V3 V4 3.5 V, and other pins left “open” (this status is
referred to as the initial status).
5. 1 Resistance between VMP and VDD (RVMD)
The resistance between VMP and VDD (RVMD) is obtained from RVMD VDD / IVMD using the current
value of the VMP pin (IVMD) when VVMP is VSS after the initial status.
5. 2 Resistance between VMP and VSS (RVMS)
The resistance between VMP and VSS (RVMS) is obtained from RVMS VDD / IVMS using the current
value of the VMP pin (IVMS) when V1 V2 V3 V4 1.8 V after the initial status.
5. 3 VC1 Pin Current (IVC1), VC2 Pin Current (IVC2), VC3 Pin Current (IVC3), VC4 Pin Current (IVC4)
At the initial status, the current that flows through the VC1 pin is the VC1 pin current (IVC1), the current
that flows through the VC2 pin is the VC2 pin current (IVC2), the current that flows through the VC3 pin
is the VC3 pin current (IVC3), and the current that flows through the VC4 pin is the VC4 pin current
(IVC4).
5. 4 CTL pin Current “H” (ICTLH), CTL Pin Current “L” (ICTLL)
In the initial status, the current that flows through the CTL pin is the CTL pin current “L” (ICTLL), after
that, when VCTL VDD, the current that flows through the CTL pin is the CTL pin current “H” (ICTLH).
5. 5 SEL Pin Current “H” (ISELH), SEL Pin Current “L” (ISELL)
In the initial status, the current that flows through the SEL pin is the SEL pin current “H” (ISELH), after
that, when VSEL VSS, the current that flows through the SEL pin is the SEL pin current “L” (ISELL).
11
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
5. 6 COP Pin Leakage Current (ICOH), COP Pin Sink Current (ICOL)
The COP pin sink current (ICOL) is the current that flows through the COP pin when VCOP VSS 0.5 V
after the initial status. After that, the current that flows through the COP pin when V1 V2 V3 V4
6 V and VCOP VDD is the COP pin leakage current (ICOH).
5. 7 DOP Pin Source Current (IDOH), DOP Pin Sink Current (IDOL)
The DOP pin sink current (IDOL) is the current that flows through the DOP pin when VDOP VSS 0.5 V
after the initial status. After that, the current that flows through the DOP pin when VVMP VDD 2 V
and VDOP VDD 0.5 V is the DOP pin source current (IDOH).
S-8254A
A
1
2
3
4
5
6
7
8
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
V1
V2
V3
V4
C1 =
0.1 F
Figure 4 Test Circuit 1
S-8254A
V
V
1
2
3
4
5
6
7
8
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
Figure 5 Test Circuit 2
12
V1
V2
V3
V4
C1 =
0.1 F
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
S-8254A
V
C2 =
0.1 F
V
C3 =
0.1 F
1
2
3
4
5
6
7
8
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
V1
V2
V3
V4
C1 =
0.1 F
Figure 6 Test Circuit 3
S-8254A
1
2
3
4
5
6
7
8
V
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
V1
V2
V3
V4
C1 =
0.1 F
Figure 7 Test Circuit 4
S-8254A
A
A
A
1
2
3
4
5
6
7
8
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
A
A
A
A
A
A
V1
V2
V3
V4
C1 =
0.1 F
Figure 8 Test Circuit 5
13
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Operation
Remark Refer to “ Battery Protection IC Connection Example”.
1. Normal Status
When the voltage of each of the batteries is in the range from VDLn to VCUn and the discharge current is
lower than the specified value (the VINI pin voltage is lower than VIOV1 and VIOV2, and the VMP pin voltage
is higher than VIOV3), the charging and discharging FETs are turned on.
2. Overcharge Status
When the voltage of one of the batteries becomes higher than VCUn and the state continues for tCU or
longer, the COP pin becomes high impedance. The COP pin is pulled up to the EB pin voltage by an
external resistor, and the charging FET is turned off to stop charging. This is called the overcharge
status. The overcharge status is released when one of the following two conditions holds.
(1) The voltage of each of the batteries becomes VCLn or lower.
(2) The voltage of each of the batteries is VCUn or lower, and the VMP pin voltage is 39 / 40 VDD or
lower (a load is connected and discharging is started via the body diode of the charging FET).
3. Overdischarge Status
When the voltage of one of the batteries becomes lower than VDLn and the state continues for tDL or
longer, the DOP pin voltage becomes VDD level, and the discharging FET is turned off to stop discharging.
This is called the overdischarge status.
3. 1 Power-down Function
When the overdischarge status is reached, the VMP pin is pulled down to the VSS level by the
internal RVMS resistor of the IC. When the VMP pin voltage is VDD / 2 or lower, the power-down
function starts to operate and almost every circuit in the S-8254A Series stops working. The
conditions of each output pin are as follows.
(1) COP pin : High-Z
(2) DOP pin : VDD
The power-down function is released when the following condition holds.
(1) The VMP pin voltage is VDD / 2 or higher.
The overdischarge status is released when the following two conditions hold.
(1) In case the VMP pin voltage is VDD / 2 or higher and the VMP pin voltage is lower than VDD, the
overdischarge status is released when the voltage of each of the batteries is VDUn or higher.
(2) In case a charger is connected, the overdischarge hysteresis is released. And the
overdischarge status is released when the voltage of each of the batteries is VDLn or higher.
14
Rev.5.2_01
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
4. Overcurrent Status
The S-8254A Series has three overcurrent detection levels (VIOV1, VIOV2, and VIOV3) and three overcurrent
detection delay times (tIOV1, tIOV2, and tIOV3) corresponding to each overcurrent detection level. When the
discharging current becomes higher than the specified value (the voltage between VSS and VINI is greater
than VIOV1) and the state continues for tIOV1 or longer, the S-8254A Series enters the overcurrent status, in
which the DOP pin voltage becomes VDD level to turn off the discharging FET to stop discharging, the
COP pin becomes high impedance and is pulled up to the EB pin voltage to turn off the charging FET to
stop charging, and the VMP pin is pulled up to the VDD voltage by the internal resistor (RVMD). Operation
of overcurrent detection level 2 (VIOV2) and overcurrent detection delay time 2 (tIOV2) is the same as for
VIOV1 and tIOV1.
In the overcurrent status, the VMP pin is pulled up to the VDD level by the internal resistor in the IC (RVMD
resistor). The overcurrent status is released when the following condition holds.
(1) The VMP pin voltage is VIOV3 or higher because a charger is connected or the load (30 M or
more) is released.
5. 0 V Battery Charge Function
Regarding the charging of a self-discharged battery (0 V battery), the S-8254A Series has two functions
from which one should be selected.
(1) 0 V battery charging is allowed (0 V battery charging is available.)
When the charger voltage is higher than V0CHA, the 0 V battery can be charged.
(2) 0 V battery charging is prohibited (0 V battery charging is unavailable.)
When the battery voltage is V0INH or lower, the 0 V battery cannot be charged.
Caution When the VDD pin voltage is lower than the minimum value of VDSOP, the operation of the
S-8254A Series is not guaranteed.
6. Delay Time Setting
The overcharge detection delay time (tCU) is determined by the external capacitor connected to the CCT
pin. The overdischarge detection delay time (tDL) and overcurrent detection delay time 1 (tIOV1) are
determined by the external capacitor connected to the CDT pin. Overcurrent detection delay times 2 and
3 (tIOV2, tIOV3) are fixed internally.
min. typ. max.
tCU [s] (5.00, 10.0, 15.0) CCCT [F]
tDL [s] (0.50, 1.00, 1.50) CCDT [F]
tIOV1 [s] (0.05, 0.10, 0.15) CCDT [F]
7. CTL Pin
The S-8254A Series has control pins. The CTL pin is used to control the COP and DOP pin output
voltages. CTL pin takes precedence over the battery protection circuit.
Table 5 Conditions Set by CTL Pin
CTL Pin
COP Pin
DOP Pin
High
High-Z
VDD
Open
High-Z
VDD
*1
Normal
status *1
Normal
status
Low
*1. The status is controlled by the voltage detector.
Caution Please note unexpected behavior might occur when electrical potential difference
between the CTL pin (‘L’ level) and VSS is generated through the external filter
(RVSS and CVSS) as a result of input voltage fluctuations.
15
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
8. SEL pin
The S-8254A Series has control pins. The SEL pin is used to switch between 3-cell and 4-cell protection.
When the SEL pin is low, overdischarge detection of the V4 cell is prohibited and an overdischarge is not
detected even if the V4 cell is shorted, therefore, the V4 cell can be used for 3-cell protection. The SEL
pin takes precedence over the battery protection circuit. Use the SEL pin at high or low.
Table 6 Conditions Set by SEL Pin
SEL Pin
High
Open
Low
16
Condition
4-cell protection
Undefined
3-cell protection
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Timing Chart
1. Overcharge Detection and Overdischarge Detection
VCUn
VCLn
Battery voltage
VDUn
VDLn
(n = 1 to 4)
VDD
DOP pin voltage
VSS
VEB
COP pin voltage
High-Z
High-Z
VSS
VEB
VDD
39 / 40VDD
VMP pin voltage
1 / 2VDD
VSS
Charger connection
Load connection
Overcharge detection delay time (tCU)
Status*1
Overdischarge detection delay time (tDL)
*1. < 1 > : Normal status
< 2 > : Overcharge status
< 3 > : Overdischarge status
< 4 > : Power-down status
Remark The charger is assumed to charge with a constant current. VEB indicates the open voltage of
the charger.
Figure 9
17
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
2. Overcurrent detection
VHC
VCUn
VCLn
Battery voltage
VDUn
VDLn
VHD
(n = 1 to 4)
VDD
DOP pin voltage
VSS
VEB
High-Z
COP pin voltage
High-Z
High-Z
VSS
VDD
VIOV3
VMP pin voltage
VSS
VDD
VINI pin voltage VIOV2
VIOV1
VSS
Load connection
Status*1
Overcurrent 1 detection
delay time (tIOV1)
Overcurrent 2 detection Overcurrent 3 detection
delay time (tIOV3)
delay time (tIOV2)
*1. < 1 > : Normal status
< 2 > : Overcurrent status
Remark The charger is assumed to charge with a constant current. VEB indicates the open voltage of
the charger.
Figure 10
18
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Battery Protection IC Connection Example
1. 3-serial Cell
Charging Discharging
FET
FET
EB
RVMP
RDOP
RCOP
S-8254A
1
2
3
4
5
6
7
8
RVINI
CCDT
CCCT
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
CVC1
CVC2
CVC3
RVC1
RVC2
RVC3
RCTL
RSEL
CTL
CVSS
RVSS
RSENSE
EB
Figure 11
2. 4-serial Cell
Charging Discharging
FET
FET
EB
RVMP
RDOP
RCOP
RVINI
CCDT
CCCT
S-8254A
1
2
3
4
5
6
7
8
COP
VMP
DOP
VINI
CDT
CCT
VSS
NC
VDD
VC1
VC2
VC3
VC4
CTL
SEL
NC
16
15
14
13
12
11
10
9
CVC1
CVC2
CVC3
RVC1
RVC2
RVC3
RVC4
RCTL
CVC4
RSEL
CTL
CVSS
RVSS
RSENSE
EB
Figure 12
19
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Table 7 Constants for External Components
Symbol
Min.
Typ.
0
1
0
1
0
1
0
1
RDOP
2
5.1
RCOP
0.1
1
RVMP
1
5.1
RCTL
1
1
RVINI
1
1
RSEL
1
1
RSENSE
0
*1
RVSS
10
51
CVC1*1
0
0.1
CVC2*1
0
0.1
CVC3*1
0
0.1
*1
CVC4
0
0.1
CCCT
0.01
0.1
CCDT
0.07
0.1
CVSS*1
2.2
2.2
*1. Please set up a filter constant to be RVSS CVSS 51 F and
RVC3 CVC3 = R VC4 CVC4 = RVSS CVSS.
RVC1*1
RVC2*1
RVC3*1
RVC4*1
Caution
Max.
1
1
1
1
10
1
10
100
100
100
51
0.33
0.33
0.33
0.33
10
to be RVC1 CVC1 =
Unit
k
k
k
k
k
M
k
k
k
k
m
F
F
F
F
F
F
F
RVC2 CVC2 =
1. The above constants may be changed without notice.
2. It is recommended that filter constants between VDD and VSS should be set
approximately to 112 F .
e.g. CVSS RVSS 2.2 F 51 112 F
Enough evaluation of transient power supply variation and overcurrent protection
function in the actual application is needed to determine the proper constants. Contact
our sales office in case the constants should be set to other than 112 F • or so.
3. It has not been confirmed whether the operation is normal or not in circuits other than
the above example of connection. In addition, the example of connection shown above
and the constant do not guarantee proper operation. Perform thorough evaluation
using the actual application to set the constant.
Precautions
The application conditions for the input voltage, output voltage, and load current should not exceed the
package power dissipation.
Batteries can be connected in any order, however, there may be cases when discharging cannot be
performed when a battery is connected. In this case, short the VMP pin and VDD pin or connect the
battery charger to return to the normal status.
When an overcharged battery and an overdischarged battery intermix, the circuit is in both the overcharge
and overdischarge statuses, so charging and discharging are not possible.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in
electrostatic protection circuit.
ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by
products including this IC of patents owned by a third party.
20
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
Characteristics (Typical Data)
1. Current Consumption
40
35
30
25
20
15
10
5
0
0
1. 2 IOPE vs. Ta
IOPE [A]
IOPE [A]
1. 1 IOPE vs. VDD
5
10
15
VDD [V]
20
24
0.10
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0.00
0
0
25
Ta [C]
50
75 85
1. 4 IPDN vs. Ta
IPDN [A]
IPDN [A]
1. 3 IPDN vs. VDD
40
35
30
25
20
15
10
5
0
40 25
5
10
15
VDD [V]
20
24
0.10
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0.00
40 25
0
25
Ta [C]
50
75 85
2. Overcharge Detection / Release Voltage, Overdischarge Detection / Release Voltage, Overcurrent
Detection Voltage, and Delay Times
4.375
4.370
4.365
4.360
4.355
4.350
4.345
4.340
4.335
4.330
4.325
40 25
2. 2 VCL vs. Ta
4.20
4.18
VCL [V]
VCU [V]
2. 1 VCU vs. Ta
0
25
Ta [C]
50
4.10
40 25
75 85
0
25
Ta [C]
50
75 85
0
25
Ta [C]
50
75 85
2. 4 VDL vs. Ta
VDL [V]
VDU [V]
4.14
4.12
2. 3 VDU vs. Ta
2.80
2.78
2.76
2.74
2.72
2.70
2.68
2.66
2.64
2.62
2.60
40 25
4.16
0
25
Ta [C]
50
75 85
2.08
2.06
2.04
2.02
2.00
1.98
1.96
1.94
1.92
40 25
21
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
0.35
0.34
0.33
0.32
0.31
0.30
0.29
0.28
0.27
0.26
0.25
10
2. 6 VIOV1 vs. Ta
VIOV1 [V]
VIOV1 [V]
2. 5 VIOV1 vs. VDD
11
12
13
14
VDD [V]
15
16
11
12
13
14
VDD [V]
15
16
1.0
1.0
1.1
1.1
VIOV3 [V]
0.9
1.2
1.3
11
12
13
14
VDD [V]
15
75 85
0
25
Ta [C]
50
75 85
0
25
Ta [C]
50
75 85
1.2
1.3
1.5
40 25
16
2. 12 tCU vs. Ta
100
1.4
10
1.2
tCU [s]
tCU [s]
50
1.4
2. 11 tCU vs. CCCT
1
1.0
0.8
0.1
0.01
0.01
25
Ta [C]
2. 10 VIOV3 vs. Ta
1.4
22
0.60
0.58
0.56
0.54
0.52
0.50
0.48
0.46
0.44
0.42
0.40
40 25
0.9
1.5
10
0
2. 8 VIOV2 vs. Ta
2. 9 VIOV3 vs. VDD
VIOV3 [V]
0.325
0.320
0.315
0.310
0.305
0.300
0.295
0.290
0.285
0.280
0.275
40 25
VIOV2 [V]
VIOV2 [V]
2. 7 VIOV2 vs. VDD
0.60
0.58
0.56
0.54
0.52
0.50
0.48
0.46
0.44
0.42
0.40
10
Rev.5.2_01
0.1
CCCT [F]
1
0.6
40 25
0
25
Ta [C]
50
75 85
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
2. 14 tDL vs. Ta
10
200
1
150
tDL [ms]
tDL [s]
2. 13 tDL vs. CCDT
0.1
50
0.01
0.001
0.07 0.1
0
40 25
1
CCDT [F]
2. 15 tIOV1 vs. CCDT
1
20
0.1
15
0.01
0.0001
0.07 0.1
50
75 85
0
25
Ta [C]
50
75 85
10
0
40 25
1
CCDT [F]
2. 17 tIOV2 vs. Ta
2. 18 tIOV3 vs. Ta
500
2.0
400
1.5
tIOV3 [ms]
tIOV2 [ms]
25
Ta [C]
5
0.001
1.0
0.5
0
40 25
0
2. 16 tIOV1 vs. Ta
tIOV1 [ms]
tIOV1 [s]
100
300
200
100
0
25
Ta [C]
50
75 85
0
40 25
0
25
Ta [C]
50
75 85
23
BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK
S-8254A Series
Rev.5.2_01
3. COP / DOP Pin
0.10
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
3. 2 ICOL vs. VCOP
25
20
ICOL [mA]
ICOH [A]
3. 1 ICOH vs. VCOP
0
5
10
15
VCOP [V]
20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
0
0
24
3.5
7
VCOP [V]
10.5
14
7
VDOP [V]
10.5
14
3. 4 IDOL vs. VDOP
25
20
IDOL [mA]
IDOH [mA]
10
5
3. 3 IDOH vs. VDOP
24
15
15
10
5
1.8
3.6
VDOP [V]
5.4
7.2
0
0
3.5
5.1±0.2
0.65
16
9
1
8
0.17±0.05
0.22±0.08
No. FT016-A-P-SD-1.2
TITLE
TSSOP16-A-PKG Dimensions
FT016-A-P-SD-1.2
No.
ANGLE
UNIT
mm
ABLIC Inc.
+0.1
4.0±0.1
ø1.5 -0
0.3±0.05
2.0±0.1
8.0±0.1
1.5±0.1
ø1.6±0.1
(7.2)
4.2±0.2
+0.4
6.5 -0.2
1
16
8
9
Feed direction
No. FT016-A-C-SD-1.1
TITLE
TSSOP16-A-Carrier Tape
No.
FT016-A-C-SD-1.1
ANGLE
UNIT
mm
ABLIC Inc.
21.4±1.0
17.4±1.0
+2.0
17.4 -1.5
Enlarged drawing in the central part
ø21±0.8
2±0.5
ø13±0.2
No. FT016-A-R-SD-2.0
TITLE
TSSOP16-A- Reel
FT016-A-R-SD-2.0
No.
ANGLE
UNIT
QTY.
mm
ABLIC Inc.
2,000
21.4±1.0
17.4±1.0
+2.0
17.4 -1.5
Enlarged drawing in the central part
ø21±0.8
2±0.5
ø13±0.2
No. FT016-A-R-S1-1.0
TITLE
TSSOP16-A- Reel
No.
FT016-A-R-S1-1.0
ANGLE
QTY.
UNIT
mm
ABLIC Inc.
4,000
Disclaimers (Handling Precautions)
1.
All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2.
The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4.
Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5.
Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6.
When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7.
The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8.
The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9.
In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
工商网监
湘ICP备2023018690号
