1721

Luckylight 12 Segment Light Bars Displays Technical Data Sheet Model No.: KWL-R1230XDUGB Spec No.: W123010A/BEG Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: April/15/2009 Drawn: Liu Page: 1 OF 7 http://www.luckylightled.com Luckylight Features: ◇ Industrial standard size. ◇ Low power consumption. ◇ Categorized for luminous intensity. ◇ The product itself will remain within RoHS compliant Version. Descriptions: ◇ The KWL-R1230 series is 12 Segment light bar display, designed for viewing distances up to 7 meters. ◇ These devices are available with green offering a wide possibility in design. ◇ These devices are made with white segments and black surface. Applications: ◇ Audio equipment. ◇ Instrument panels. ◇ Digital read out display. Device Selection Guide: Model No. Chip Material D Source Color GaAlAs Super Red KWL-R1230ADUGB Common Anode UG AlGaInP Super Yellow Green D GaAlAs Super Red KWL-R1230CDUGB Common Cathode UG Spec No.: W123010A/BEG Approved: JoJo Descriptions AlGaInP Super Yellow Green Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: April/15/2009 Drawn: Liu Page: 2 OF 7 http://www.luckylightled.com Luckylight Package Dimension: PIN 1 7.42 [0.292] 10.1 [0.398] + 10.1 [0.398] + 8 [0.315] PIN 14 1.74 [0.069] 6.3 [0.248]±0.5 2.54*11=27.94 [1.101] 30.4 [1.198] 30.4 [1.198] A B C D E F G H I J K L Model No. φ0.5 [0.020] 2.54*6=15.24 [0.600] KWL-R1230ADUGB 1,14 A B KWL-R1230CDUGB 6,9 C D E F 1,14 7,8 G H I J K L 2 13 3 12 4 11 5 10 A B 6,9 C D E F 7,8 G H I J K L 2 13 3 12 4 11 5 10 Red Green Red Green Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25 mm (.010″) unless otherwise noted. 3. Specifications are subject to change without notice. Spec No.: W123010A/BEG Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: April/15/2009 Drawn: Liu Page: 3 OF 7 http://www.luckylightled.com Luckylight Absolute Maximum Ratings at Ta=25℃ Symbol Red Green Unit Power Dissipation PD 60 70 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) IFP 100 100 mA Forward Current IF 25 25 mA 0.4 0.4 mA/℃ 5 5 V Parameters Derating Linear From 25℃ Reverse Voltage VR Operating Temperature Range Topr -40℃ to +80℃ Storage Temperature Range Tstg -40℃ to +85℃ Soldering Temperature Tsld 260℃ for 5 Seconds Electrical Optical Characteristics at Ta=25℃ Parameters Symbol Color Luminous Intensity Iv Peak Emission Wavelength λp Dominant Wavelength λd Spectral Line Half-Width △λ Forward Voltage VF Reverse Current IR Min. Typ. Max. Red 7.0 14.0 --- Green 6.5 13.0 --- Red --- 660 --- Green --- 575 --- Red --- 640 --- Green --- 572 --- Red --- 20 --- Green --- 20 --- Red --- 1.8 2.4 Green --- 2.2 2.8 Red --- --- 50 Unit Test Condition mcd IF=20mA (Note 1) nm IF=20mA nm IF=20mA (Note 2) nm IF=20mA V IF=20mA µA VR=5V Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No.: W123010A/BEG Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: April/15/2009 Drawn: Liu Page: 4 OF 7 http://www.luckylightled.com Luckylight Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Red Spectrum Distribution Relative Luminous Intensity (%) Ta=25℃ 100 75 50 25 0 500 550 600 650 700 Wavelength λp (nm) Forward Current & Forward Voltage Forward Current Derating Curve Ta=25℃ 50 20 10 0 Relative Luminous Intensity (%) Forward Current IF (mA) 30 1000 40 30 25 20 10 0 1.4 1.8 2.2 2.6 3.0 Forward Voltage VF (V) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) Spec No.: W123010A/BEG Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. 0 3.4 20 40 60 80 100 Ambient Temperature Ta (℃) Luminous Intensity & Forward Current Relative Luminous Intensity (%) Forward Current IF (mA) 50 40 750 Ta=25℃ 1000 f=1KHz Duty=1/10 100 10 1 0 10 1 2 10 10 10 Forward Current IF (mA) Date: April/15/2009 Drawn: Liu 3 Page: 5 OF 7 http://www.luckylightled.com Luckylight Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Green Forward Current & Forward Voltage Ta=25℃ 75 50 25 0 300 1000 Ta=25℃ Forward Current IF (mA) 100 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 1.6 1.8 2.0 2.2 2.4 2.6 2.8 Forward Voltage VF (V) 800 Luminous Intensity & Forward Current Relative Luminous Intensity (%) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Spectrum Distribution Ta=25℃ 1000 f=1KHz Duty=1/10 100 10 1 0 10 1 2 3 10 10 10 Forward Current IF (mA) Forward Current IF (mA) Forward Current Derating Curve 50 40 30 25 20 10 0 Spec No.: W123010A/BEG Approved: JoJo 0 20 40 60 80 100 Ambient Temperature Ta (℃) Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: April/15/2009 Drawn: Liu Page: 6 OF 7 http://www.luckylightled.com Luckylight Please read the following notes before using the datasheets: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 If the package contains a moisture proof bag inside, please don't open the package before using. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 80%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 3. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4. Soldering When soldering, for Lamp without stopper type and must be leave a minimum of 3mm clearance from the base of the lens to the soldering point. To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Soldering Iron Temperature Soldering Time Wave Soldering 300℃ Max. 3 sec. Max. (one time only) Pre-heat Pre-heat Time Solder Wave Soldering Time 100℃ Max. 60 sec. Max. 260℃ Max. 5 sec. Max. Note: Excessive soldering temperature and / or time might result in deformation of the LED lens or catastrophic failure of the LED. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Spec No.: W123010A/BEG Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: April/15/2009 Drawn: Liu Page: 7 OF 7 http://www.luckylightled.com