879

Luckylight 0.56" Quadruple Digit Numeric Displays Technical Data Sheet Model No.: KW4-56NXUYA-P Spec No.:W5643E/F Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: Oct/23/2006 Drawn: Liu Page: 1 OF 6 http://www.luckylightled.com Luckylight Features: ◇ 0.56″ (inch) digit height. ◇ Excellent segment uniformity. ◇ Sold state reliability. ◇ Industrial standard size. ◇ Low power consumption. ◇ The product itself will remain within RoHS compliant Version. Descriptions: ◇ The KW4-56NXXX series is a lager 14.20 mm (0.56″) high seven segments display designed for viewing distances up to 7 meters. ◇ These displays provide excellent reliability in bright ambient light. ◇ These devices are made with White segments and gray surface Applications: ◇ Audio equipment. ◇ Instrument panels. ◇ Digital read out display. Device Selection Guide: Model No. Chip Material KW4-56NAUYA-P Source Color Description Super Yellow Common Anode Super Yellow Common Cathode AlGaInP KW4-56NCUYA-P Spec No.:W5643E/F Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: Oct/23/2006 Drawn: Liu Page: 2 OF 6 http://www.luckylightled.com Luckylight Package Dimension: 8.1 [0.319 ] 8° + + + + 14.20 [0.56''] 1.35 [0.053 ] 8 [0.315] 15.24 [0.600] PIN 7 19 [0.749] PIN 12 PIN 6 PIN 1 6.3 [0.248]±0.5 12.7*3=38.1 [1.501] DIG.1 A 50 .2[1.978] DIG.2 DIG.3 DIG.4 D5 F B G E Φ0.5 [0.020] D6 C DP D 2.54*6=15.24 [0.600] KW4-56NAUYA-P 14 (COM) 11 (COM) B 13 9 C 4 D 2 E F G DP 1 12 5 10 (COM) DIG.2 DIG.1 A 7 (COM) A B C D E F DIG.3 G DP D5 D6 A 3 6 (COM) B C D E F G DP A DIG.4 B C D E F G DP 8 KW4-56NCUYA-P 14 (COM) 11 (COM) DIG.2 DIG.1 A B 13 9 C 4 D 2 E F G DP 1 12 5 10 (COM) 7 (COM) A B C D E F DIG.3 G DP D5 D6 A 3 6 (COM) B C D E F G DP A DIG.4 B C D E F G DP 8 Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25 mm (.010″) unless otherwise noted.. 3. Specifications are subject to change without notice. Spec No.:W5643E/F Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: Oct/23/2006 Drawn: Liu Page: 3 OF 6 http://www.luckylightled.com Luckylight Absolute Maximum Ratings at Ta=25℃ Parameters Symbol Max. Unit Power Dissipation (Per Segment) PD 70 mW Peak Forward Current (Per Segment) (1/10 Duty Cycle, 0.1ms Pulse Width) IFP 100 mA IF 25 mA 0.4 mA/℃ 5 V Forward Current (Per Segment) Dating Linear From 25℃ Reverse Voltage VR Operating Temperature Range Topr -40℃ to +80℃ Storage Temperature Range Tstg -40℃ to +85℃ Soldering Temperature Tsld 260℃ for 5 Seconds Electrical Optical Characteristics at Ta=25℃ Parameters Symbol Min. Typ. Max. Unit Luminous Intensity mcd Test Condition IV 7.0 14.0 --- IF=20mA (Note 1) Luminous Intensity Matching Ratio (Segment To Segment) Iv-m --- --- 2:1 Peak Emission Wavelength λp --- 590 --- nm IF=20mA Dominant Wavelength λd --- 588 --- nm IF=20mA (Note 2) Spectral Line Half-Width △λ --- 15 --- nm IF=20mA Forward Voltage VF --- 2.1 2.8 V IF=20mA Reverse Current IR --- --- 50 µA VR=5V IF=10mA Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No.:W5643E/F Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: Oct/23/2006 Drawn: Liu Page: 4 OF 6 http://www.luckylightled.com Luckylight Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Ta=25℃ Forward Current IF (mA) 100 Forward Current & Forward Voltage 75 50 25 0 300 1000 400 500 600 700 Wavelength λ p (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃ ) Ta=25℃ 50 40 30 20 10 0 1.5 800 1.7 1.9 2.1 2.3 2.5 Forward Voltage VF (V) 2.7 Luminous Intensity & Forward Current Relative Luminous Intensity (%) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Spectrum Distribution Ta=25℃ 1000 f=1KHz Duty=1/10 100 10 1 0 10 1 2 3 10 10 10 Forward Current IF (mA) Forward Current IF (mA) Forward Current Derating Curve 50 40 30 25 20 10 0 Spec No.:W5643E/F Approved: JoJo 0 20 40 60 80 100 Ambient Temperature Ta (℃ ) Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: Oct/23/2006 Drawn: Liu Page: 5 OF 6 http://www.luckylightled.com Luckylight Please read the following notes before using the datasheets: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 If the package contains a moisture proof bag inside, please don't open the package before using. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 80%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 3. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4. Soldering When soldering, for Lamp without stopper type and must be leave a minimum of 3mm clearance from the base of the lens to the soldering point. To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Soldering Iron Temperature Soldering Time 300℃ Max. 3 sec. Max. (one time only) Wave Soldering Pre-heat Pre-heat Time Solder Wave Soldering Time 100℃ Max. 60 sec. Max. 260℃ Max. 5 sec. Max. Note: Excessive soldering temperature and / or time might result in deformation of the LED lens or catastrophic failure of the LED. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used . It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Spec No.:W5643E/F Approved: JoJo Rev No.: V.2 Checked: Sun Lucky Light Electronics Co., Ltd. Date: Oct/23/2006 Drawn: Liu Page: 6 OF 6 http://www.luckylightled.com