A10315

Reflexus Penta-band SMD Antenna Part No. A10315 Product Specification 1 Features • • • • • • GSM/UMTS antenna supporting up to 5 frequency bands Complementary antenna technology provides resistance to de-tuning High efficiency Easy to integrate Intended for SMD mounting Supplied in tape on reel Reflexus supports the following communication standards: GSM/GPRS/EDGE GSM850 (E)GSM900 GSM1800 (DCS) GSM1900 (PCS) CDMA2000 1xRTT/EV-DO/EV-DV UMTS WCDMA/HSPA Band Classes: 1,2,3,4,6,8,9,12,14,15 Bands I – VI Bands VIII – X Other Standards Korean PCS DECT (outside USA) TD-SCDMA AWS 2 Description Reflexus uses a ground plane in order to radiate efficiently, but this ground plane must not extend underneath the antenna itself. The antenna uses a matching circuit to achieve optimized results for the specific frequency bands that are required. This product specification shows the performance of the antenna when optimized to cover a typical penta-band reception: GSM850/900/1800/1900 and WCDMA. 3 Applications • • • • • Mobile handsets Femto / Pico base stations Tracker devices Machine to machine communication Remote monitoring Integrated Antenna and RF Solutions 1 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 4 Part numbers A10315 150 5 General data Product name Reflexus GSM SMD Part Numbers A10315 Frequency (typical) 824MHz-960MHz 1710MHz -2170MHz Polarization Linear Operating temperature -40 ºC to +85 ºC Impedance with matching 50 Ω Weight 2.5g Antenna type SMD Dimensions 40 x 10 x 3.2 [mm] 6 Electrical characteristics Typical performance Peak gain Conditions 2dBi @ 876Mhz 3.7dBi @ 1917Mhz -1.3dBi 824-960 MHz Average gain -1.5dBi 1710-2170 MHz All data measured on Antenova’s reference board, part number A10315-U1M Data given for the 824MHz-960MHz and 1710MHz-2170MHz frequency ranges Average efficiency 824-960 MHz 1710-2170 MHz 70% >60% Maximum Return Loss -8dB Maximum VSWR 2.3:1 Integrated Antenna and RF Solutions 2 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 7 Electrical performance 7-1 Return Loss 5 [dB] mtool5 0 -5 3 ∇ 1 -10 ∇ 2 ∇ -15 4 ∇ -20 -25 800 1000 1200 MAR KERS: 1400 MHz 1600 1800 dB 2000 MHz 2200 [MHz] 2400 dB R e fle x us.S1P 1: 824 2: 960 -10.00 -13.46 3: 1710 4: 2170 -8.75 -17.09 7-2 VSWR mtool5 10 9 8 7 6 5 4 3 1 2 ∇ 1 800 3 ∇ 2 4 ∇ 1000 MAR KERS: ∇ 1200 1400 1600 MHz 1800 2000 2200 [MHz] 2400 MHz R e fle x us.S1P 1: 824 2: 960 1.93 1.54 3: 1710 4: 2170 2.15 1.33 Integrated Antenna and RF Solutions 3 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 7-3 Antenna patterns 824-960 MHz Z Y X 0º 0º 0º 270º 90º 180º 270º 90º 270º 90º 180º XY plane ZY plane 180º XZ plane Patterns show combined polarisations measured on reference board A10315-U1M. 3D Pattern measured at 890MHz Integrated Antenna and RF Solutions 4 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 7-4 Antenna patterns 1710 – 2170 MHz Z X 0º 0º 270º 90º 180º XY plane Y 0º 270º 90º 270º 90º 180º ZY plane 180º XZ plane Patterns show combined polarisations measured on reference board A10315-U1M. 3D Pattern measured at 1894MHz Integrated Antenna and RF Solutions 5 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 8 Antenna efficiency 100 Free Space Terminal Efficiency [%] 90 80 Average 76% 70 Average 74% Average 71% Average 66% Average 69% 60 50 40 30 20 10 Frequency [MHz] 0 824 880 GSM850 894 960 1710 1850 1880 1920 GSM900 1990 2170 UMTS2100 DCS1800 PCS1900 Reflexus efficiency in free space 9 Antenna dimensions L W H Length Width Height 40.0 +/- 0.2 10.4 +/-0.2 3.2 +/- 0.15 E N T G 0.2 +/0.15 28.28 +/0.15 0.9+/-0.15 10.56 +/0.15 R M 1.5 +/-0.15 0.2+/-0.15 V O K 1.0 +/0.15 22 +/- 0.15 16.5 +/0.15 Dimensions in mm Integrated Antenna and RF Solutions 6 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 10 Antenna footprint Reflexus GSM (Part No: A10315) CAD files of the antenna footprint are available from Antenova on request. Please contact info@antenova.com for further details. X P C G I J K S M O V T L 4.0 +/-0.1 1.0 +/-0.1 2.7 +/-0.1 1.5 +/-0.1 0.5 +/-0.1 1.5 +/-0.1 1.5 +/- 0.1 9.0 +/-0.1 2.6 +/-0.1 28.58 +/-0.1 0.6 +/- 0.1 0.9 +/- 0.1 10.86 +/- 0.1 Integrated Antenna and RF Solutions 7 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 11 Electrical interface 11-1 Transmission lines The antenna should be connected using an RF transmission line. All transmission lines should be designed to have a characteristic impedance of 50 Ω The length of the transmission lines should be kept to a minimum. Any other parts of the RF system like transceivers, power amplifiers, etc, should also be designed to have an impedance of 50 Ω Once the material for the PCB has been chosen (PCB thickness and dielectric constant), a coplanar transmission line can easily be designed using any of the commercial software packages for transmission line design. For the chosen PCB thickness, copper thickness and substrate dielectric constant, the program will calculate the appropriate transmission line width and gaps on either side of the track so the characteristic impedance of the co-planar transmission line is 50 Ω. Integrated Antenna and RF Solutions 8 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 11-2 Matching circuit The antenna requires a matching circuit that must be optimized for each customer’s product. The matching circuit will require up to five components depending on the impedance of the antenna when situated in the device, and pads have been designed for 0603 components for best results. In addition to the matching circuit, a separate DC blocking capacitor will also be required between the radio and the antenna matching circuit. The following pad layout should be designed into the device so the correct circuit can be installed: Note: The component values for the matching circuit will vary depending on the size of the PCB and surrounding components. The impedance of the antenna should be measured before selecting suitable matching components. Antenova offers a matching service on request. Contact info@antenova.com for further information. Integrated Antenna and RF Solutions 9 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 11-3 Antenna placement Reflexus should be fitted to the device so that power from the antenna can radiate into free space. Antenova strongly recommends placing the antenna near the edge of the board. Maximum antenna performance is achieved by placing the antenna close to the corner of the PCB with few components or metal objects nearby. Ground can be placed at the side of the antenna, but the remaining space ar1ound the antenna, including directly above and below should be free from components or conducting objects. The placements shown here are for guidance only, as the actual performance differences will depend on each individual device. Antenova offers a full range of development support to ensure efficient implementation of the antenna into the specific design. To overcome RF design issues, matching circuits, transmission lines, layout and other components, please contact Antenova (info@antenova.com) for design and placement recommendations. Best Performance Best Performance Integrated Antenna and RF Solutions 10 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 11-4 Reference board The reference board has been designed for evaluation purposes of Reflexus GSM antenna and it includes a SMA female connector. The reference board is available with Reflexus tuned to cover 5 bands: GSM850/900/1800/1900 and WCDMA, Part number: A10315-U1M Dimensions in mm Note: Other size reference boards are available for typical applications. Contact info@antenova.com for further information or to order a reference board. Integrated Antenna and RF Solutions 11 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 12 Soldering This antenna is suitable for lead free soldering. The reflow profile should be adjusted to suit the PCBA, oven and solder paste, while observing the following conditions: - The maximum temperature should not exceed 240 ºC - However for lead free soldering, a maximum temperature of 255 ºC for no more than 20 seconds is permitted. - The antenna should not be exposed to temperatures exceeding 120 ºC more than 3 times during the soldering process. 13 Hazardous material regulation conformance The antenna has been tested to conform to RoHS requirements. A certificate of conformance is available from Antenova’s website. 14 Packaging 14-1 Optimal storage conditions for packaged reels Temperature -10ºC to 40ºC Humidity Less than 75% RH Shelf Life 18 Months Storage place Away from corrosive gas and direct sunlight Packaging Reels should be stored in unopened sealed manufacturer’s plastic packaging. Note: Storage of open reels of antennas is not recommended due to possible oxidization of pads on antennas. If short term storage is necessary, then it is highly recommended that the bag containing the antenna reel is re-sealed and stored in like storage conditions as in above table. Integrated Antenna and RF Solutions 12 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 14-2 Tape characteristics Reflexus W F E1 P0 P1 P2 A0 B0 K0 SO T D0 56 ± 0.2 26.2 ± 0.1 1.75 ± 0.1 4 ± 0.1 20 ± 0.1 2 ± 0.1 9.3 ± 0.1 40.6 ± 0.1 1.3 ± 0.1 52.4 ± 0.1 0.3± 0.05 Min 1.5 +/- 0.1 Dimensions in mm Quantity Leading Space Trailing Space 1000 pcs / reel 50 blank antenna holders 50 blank antenna holders Integrated Antenna and RF Solutions 13 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 14-3 Reel dimensions Width Reel Diameter Hub Diameter Shaft Diameter 70 mm 330 +/- 2.0 mm 80 mm 13 +/- 0.5 mm 14-4 Box dimensions Width W Breadth B Thickness H 195 mm 195 mm 37 mm 14-5 Bag properties Reels are supplied in protective plastic packaging 14-6 Box label information Reflexus Dimensions in mm Integrated Antenna and RF Solutions 14 Product Specification 09MD-0021-3-PS Reflexus GSM SMD Antenna Part No. A10315 www.antenova.com Corporate Headquarters North America Headquarters Asia Headquarters Antenova Ltd. Far Field House Albert Road Stow-cum-Quy Cambridge CB25 9AR UK Antenova Ltd. Rogers Business Park 2541 Technology Drive Suite 403 Elgin, IL 60124 USA Antenova Asia Ltd. 4F, No. 324, Sec. 1, Nei-Hu Road Nei-Hu District Taipei 11493 Taiwan, ROC Tel: +44 1223 810600 Fax: +44 1223 810650 Email: info@antenova.com Tel: +1 (847) 551 9710 Fax +1 (847) 551 9719 Email: info@antenova.com Tel: +886 (0) 2 8797 8630 Fax: +886 (0) 2 8797 6890 Email: info@antenova.com ® ® ® Copyright 2009 Antenova Ltd. All Rights Reserved. Antenova and gigaNOVA are trademarks of Antenova Ltd. Any other names and/or trademarks belong to their respective companies. The materials provided herein are believed to be reliable and correct at the time of print. Antenova does not warrant the accuracy or completeness of the information, text, graphics or other items contained within these information. Antenova further assumes no responsibility for the use of this information, and all such information shall be entirely at the user’s risk. Integrated Antenna and RF Solutions 15 Product Specification 09MD-0021-3-PS Release Date 10 July 2009