PRODUCT CATALOG
RF & Microwave
Connectors & Cable Assemblies
Table of Contents
Emerson Network Power Connectivity Solutions has a wide range of cable assemblies and connectors suited for RF,
Microwave and Fiber Optic signal transmission. Connectivity Solutions is a vertically integrated supplier of custom, fixed
length and semi-rigid cable assemblies from DC to 50 GHz. Our product lines deliver custom-engineered products and
solutions to satisfy the most demanding and complex requirements.
AIM-Cambridge has a universal line of products that offer cost effective, high quality solutions for
connectivity. Our connectors are available in BNC, Type N, F Type, RCA, UHF, Mini-UHF, TNC, D-Sub
and Modular Plugs for Data/Telecom applications. In addition, we stock a wide variety of cables for
A/V, SATV, CATV, computer and LAN applications, as well as a complete line of termination tools
and structured cabling products. AIM-Cambridge promises that its product will provide you with
unmatched consistency, quality, reliability and ease of use.
Johnson designs and manufactures an industry leading line of RF coaxial connectors and adapters,
which are available in both 50 and 75 ohm versions. Johnson connectors are designed to provide the
highest quality data transmission for audio, video and data applications. The Johnson line of products
can address frequency ranges from DC to 46GHz and all sizes from Ultra-miniature interfaces (UMC),
Micro-miniature, (MCX, MMCX, SMP), Subminiature (SMA, SMB, SMK, kwiQMAte™), Medium
connectors (Type N connectors) through to large connectors (DIN7/16). The breadth of products
available within the Johnson range includes board and cable mount connectors as well as semi-rigid,
conformable, and flexible RF coaxial cables.
Midwest Microwave manufacturers passive coaxial microwave components that are known for their
precision performance and high quality that meets the precise requirements of the RF/Microwave
industry. Our broad product portfolio includes: Attenuators, Precision Adapters, Terminations, DC
Blocks, Power Dividers, Couplers, Equalizers, Phase Shifters, Connectors, Custom Cable Assemblies
and Test Cables that are designed and manufactured for both military and commercial applications.
Midwest also offers a wide variety of Qualified Product List (QPL) approved products in the M3933,
M39030 and M39012 series, as well as many DESC/DSCC approved models.
MMCX Connectors
50 Ohm Connectors
Specifications............................................................ 4
Semi-Rigid and Flexible Cable................................... 6
PC Mount.................................................................. 8
Termination.............................................................. 9
Non-Magnetic Connectors - 50 Ohm
Specifications...........................................................11
Semi-Rigid and Flexible Cable..................................12
PC Mount.................................................................12
Other Information
Assembly Tools......................................................185
Cable Information..................................................192
Assembly Instructions............................................193
Mounting Hole Layouts..........................................194
Index......................................................................274
Competitor Cross Reference................................. 280
Semflex designs and manufactures low loss, flexible, microwave coaxial cable and custom cable
assemblies for the military/aerospace, commercial OEM and test instrumentation markets. Semflex
offers cables ranging from DC to 50 GHz, available with ultra low insertion loss, power ratings up to
21 KW, and available with all popular connectors.
Stratos optical connectivity products is globally recognized as highly reliable, cost-effective, and
provides optical connectivity solutions that are virtually immune to dust, mud, oil, water, and other
contaminants.
Our expanded beam connectivity products are ideal for harsh environment applications in the
broadcast, industrial, petrochemical and military/aerospace markets where high reliability, low
maintenance and quick serviceability are critical requirements. Our optical active products are used
mainly in military, aerospace and industrial markets where high speed/high reliable performance is
mission critical. The actives product line includes optical transceivers, optical media converters and
custom devices tailored to your application.
13
MCX Connectors
39
SMK Connectors
45
SMA Connectors
103
SMB Connectors
131
SMC Connectors
137
SMP Connectors
145
Type N Connectors
153
Shielded Cable Terminations
157
Between-Series Adapters
161
Fixed Length Cable Assemblies
173
Ultra Miniature Connectors (UMC)
181
kwiQMAte ™ Connectors
While every precaution has been taken to ensure accuracy and completeness
herein, Emerson Network Power Connectivity Solutions assumes no responsibility,
and disclaims all liability for damages resulting from use of this information or for
any errors or omissions. Specifications subject to change without notice.
193
Assembly Instructions
257
Electronic Hardware
274 Index
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
MMCX CONNECTORS
2
MMCX Connectors
185 Tools
Trompeter is recognized as a global leader in delivering best in class RF connectivity products. The
Trompeter line of patch jacks, RF connectors, cable assemblies, HDTV digital technology and DS3
connectivity solutions is unrivalled. Our mission is to provide products that continually deliver the
highest quality signal integrity for the most demanding applications in Telecom, Central Office,
Broadcast, Military Aerospace, and Instrumentation markets worldwide. Our extensive line of costeffective products are rigorously designed and tested to provide the critically engineered solutions
necessary to enhance the end-user’s overall experience.
Vitelec provides a comprehensive range of RF coaxial interconnect products and cable assemblies.
The company has a long established reputation for offering quality and innovation with a wide range
of both standard and custom designed products for the electronic and communication industries.
3
3
MMCX CONNECTORS – 50 OHM
Specifications
Electrical Specifications
Impedance: 50 Ohms
Frequency Range:
Connectors............................................................................................................................................................... 0-6 GHz
Dummy loads.................................................................................................................................................. 0-1 GHz
VSWR (max): (f = GHz)
Straight
Right Angle
Cable Connectors Cable Connectors
.047 OD............................................................................................................................1.20
1.14 + .07f
RG-178, RG-316, RG-316 DS.............................................................................................1.20 1.25
RG-405.............................................................................................................................1.15 1.15
Uncabled receptacles, dummy loads............................................................................................................... N/A
Working Voltage:
Connectors ......................................................................................................................170 VRMS at sea level†
Dummy loads....................................................................................................................N/A
Dielectric Withstanding Voltage:
Connectors....................................................................................................................... 500 VRMS at sea level†
Dummy loads.................................................................................................................... N/A
Insulation Resistance: 1000 megohms min
Contact Resistance: (milliohms max)
After
Initial
Environmental
Center contact (straight cabled connectors and uncabled receptacles).............................5.0 8.0
Center contact (right angle cabled connectors).................................................................5.0 15.0
Outer contact (all connectors)..........................................................................................1.0 1.5
Braid to body ....................................................................................................................1.5
N/A
Corona Level:
Connectors....................................................................................................................... 190 volts min at 70,000 feet†
Dummy loads.................................................................................................................... N/A
Insertion Loss: (dB max, tested at 1 GHz)
Straight cabled connectors.............................................................................................................................. 0.1
Right angle cabled connectors......................................................................................................................... 0.2
Uncabled receptacles, dummy loads................................................................................................................ N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Flexible cable....................................................................................................................................................-60 dB
RG-405 ............................................................................................................................................................-70 dB
Dummy loads ...................................................................................................................................................N/A
RF High Potential Withstanding Voltage: (400 VRMS at 4 and 7 MHz)†
Power Rating (Dummy Load): 0.5 watt @ +25°C, derated to 0.25 watt @ +125° C
Specifications
5
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range:
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 165°C
Dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 125°C
Thermal Shock:
MIL-STD-202, Method 107, Condition C, except -55°C to +155°C (N/A dummy loads)
Corrosion:
MIL-STD-202, Method 101, Condition B (N/A dummy loads)
Shock:
MIL-STD-202, Method 213, Condition B (N/A dummy loads)
Vibration:
MIL-STD-202, Method 204, Condition D (N/A dummy loads)
Moisture Resistance: MIL-STD-202, Method 106 (N/A dummy loads)
Material Specifications
Bodies:
Brass per ASTM B16, gold plated** per MIL-DTL-45204 .00001” min
Contacts:
Beryllium copper per ASTM B196, gold plated per MIL-DTL-45204 .00003” min
Interface Spring:
Beryllium copper per ASTM B196, gold plated per MIL-DTL-45204 .00003” min
Insulators:
PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457
Crimp Sleeves:
Copper per ASTM B301 or brass per ASTM B16, gold plated per MIL-DTL-45204 .00001” min
Mounting Hardware: Brass (nuts) per ASTM B16 or phosphor bronze (lockwashers) per
ASTM B139, gold plated per MIL-DTL-45204 .00001” min
**All gold plated parts include a .00005” min nickel barrier layer.
Mating Engagement for MMCX Series
1. ID of contact to meet VSWR mating characteristics and connector durability
when mated with a dia .016 +/- .001 male contact.
2. Must meet the force to engage and disengage when mated with mating part.
†Avoid user injury due to misapplication. See safety advisory definitions inside front cover.
Engagement Design: Series MMCX
Engagement/Disengagement Force: 8 lbs max axial engagement
1.4 lbs min axial disengagement
Contact Retention: 2.0 lbs min axial force
Axial Force* (lbs)
Torque (oz-in)
Cable Retention:
.047 flexible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5
N/A
RG-178 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0
N/A
RG-316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.0
N/A
RG-316 DS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.0
N/A
RG-405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.0 16
*Or cable breaking strength whichever is less.
Durability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 cycles min
4
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MMCX CONNECTORS – 50 OHM
Mechanical Specifications
MMCX CONNECTORS – 50 OHM
Semi-Rigid and Flexible Cable
Semi-Rigid and Flexible Cable
Right Angle Solder Type Plug – Captivated Contact
7
Straight Crimp Type Plug – Solder or Crimp Captivated Contact
Cable Type
Gold Plated
“A”
“D”
Termination
Cable Type
Gold Plated
.047” OD Flexible
135-3436-001
.462 (11.73)
.137 (3.48)
Crimp Insert
RG-405
135-3693-101
RG-178, 196
135-3402-001
.462 (11.73)
.137 (3.48)
Crimp Insert
RG-316, 188, 161, 174
135-3403-001
.509 (12.93)
.173 (4.39)
Crimp Sleeve
RG-316 DS, 188 DS
135-3404-001
.509 (12.93)
.173 (4.39)
Crimp Sleeve
RG-179, 187
135-3433-001
.509 (12.93)
.173 (4.39)
Crimp Sleeve
Assembly instructions page 198.
Assembly instructions page 202 and 203.
Straight Crimp Type Jack – Solder or Crimp Captivated Contact
Right Angle Crimp Type Plug – Captivated Contact
Cable Type
Part No.
“A”
“D”
Termination
.047” OD Flexible
135-3336-001
.462 (11.73)
.137 (3.48)
Crimp Insert
RG-178, 196
135-3302-001
.462 (11.73)
.137 (3.48)
Crimp Insert
RG-316, 188, 161, 174
135-3303-001
.545 (13.84)
.173 (4.39)
Crimp Sleeve
RG-316 DS, 188 DS
135-3304-001
.545 (13.84)
.173 (4.39)
Crimp Sleeve
135-3333-001
.545 (13.84))
.173 (4.39)
Crimp Sleeve
Cable Type
Gold Plated
“A”
“B”
Termination
RG-179, 187
.047” OD Flexible
135-3436-101
.354 (8.99)
.276 (7.01)
Crimp Insert
Assembly instructions page 204 and 205.
RG-178, 196
135-3402-101
.354 (8.99)
.276 (7.01)
Crimp Insert
RG-178, 196
135-3402-111
.412 (10.46)
.334 (8.48)
Crimp Sleeve
RG-316, 188, 161, 174, 179, 187
135-3403-101
.412 (10.46)
.334 (8.48)
Crimp Sleeve
RG-316 DS, 188 DS
135-3404-101
.412 (10.46)
.334 (8.48)
Crimp Sleeve
Straight Crimp Type Bulkhead Jack – Solder or Crimp Captivated Contact
Cable Type
Gold Plated
Termination
.047” OD Flexible
135-3336-401
Crimp Insert
RG-178, 196
135-3302-401
Crimp Insert
Assembly instructions page 205.
Mounting Hole layout figure 5 page 194.
6
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MMCX CONNECTORS – 50 OHM
Assembly instructions page 200 and 201.
MMCX CONNECTORS – 50 OHM
PC Mount
PC Mount
Right Angle Jack Receptacle
9
Straight Plug Receptacle
Gold Plated
Gold Plated
“A”
135-3801-201
135-3701-301
.115 (2.92)
Mounting Hole layout figure 12 page 194.
135-3701-311
.068 (1.73)
Mounting Hole layout figure 12 page 194.
End Launch Surface Mount Jack Receptacle
Straight Jack Receptacle
Gold Plated
“A”
135-3701-201
.115 (2.92)
135-3701-211
.068 (1.73)
Gold Plated
Packaging
135-3711-801
Stock
135-3711-802
Tape and Reel, 1000 pcs/reel
Recommended Land Pattern and Board Notch figure 14 page 195.
Tape and Reel .316 (8.0) component pitch .630 (16.0) wide.
Mounting Hole layout figure 12 page 194.
Plug Dummy Load
Straight Surface Mount Jack Receptacle
Packaging
135-3711-201
Stock
135-3711-202
Tape and Reel, 1500 pcs/reel
Resistance
135-3801-811
50 Ohms
Recommended Land Pattern figure 15 page 195.
Tape and Reel .315 (8.0) component pitch .630 (16.0) wide.
8
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MMCX CONNECTORS – 50 OHM
Gold Plated
Gold Plated
NON-MAGNETIC CONNECTORS
Non-Magnetic RF Connectors
Specifications
Non-Magnetic Connectors
Electrical Specifications
Our line of non-magnetic connectors is one of many successful examples of how Johnson® commercializes the high-end,
custom application into the cost-sensitive solution that maintains the original Mil-Spec performance. As MRI and other
magnetically sensitive technologies grow and evolve so to must the Johnson connector portfolio. Stronger magnetic fields,
demands for better signal-to-noise ratios, custom-sized and modular flex coils for increasingly smaller machines: the RF
connectors within the equipment have to bear an increasingly tricky role of delivering higher through-put while creating
less interference.
Impedance: 50 Ohms
Frequency Range:.............................................................................................................................................0-6 GHz
VSWR (max): (max) (f = GHz)
Straight
Right Angle
Cabled Connectors Cabled Connectors
.047 dia...........................................................................................................................1.20
1.14 + .07f
RG-178, RG-316, RG-316 DS...........................................................................................1.20 1.25
Working Voltage:
Connectors .................................................................................................................... 170 VRMS at sea level†
Dielectric Withstanding Voltage:
Connectors .................................................................................................................... 500 VRMS at sea level†
Insulation Resistance: 1000 megohms min
Contact Resistance: (milliohms max)
Initial
After Environmental
Center contact (straight cabled connectors and uncabled receptacles)...........................5.0 8.0
Center contact (right angle cabled connectors)...............................................................5.0 15.0
Outer contact (all connectors).........................................................................................1.0 1.5
Braid to body ..................................................................................................................1.5
N/A
Corona Level:
Connectors ..............................................................................................................190 volts min at 70,000 feet†
Insertion Loss: (dB max, tested at 1 GHz)
Straight cabled connectors.............................................................................................................................. 0.1
Right angle cabled connectors......................................................................................................................... 0.2
Uncabled receptacles....................................................................................................................................... N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Flexible cable....................................................................................................................................................-60 dB
RF High Potential Withstanding Voltage: 400 VRMS min (tested at 4 and 7 MHz)†
With SMA, SMB, MCX, MMCX and soon SMP interfaces made available in a variety of PC and Cable-Mount designs, we can
deliver the imaging performance your customers count on.
• The materials and finishes of our connectors meet the stringent limits of image and magnetic field distortion
in an MR environment.
• The connector electrical performance exceeds the frequency requirements of the Receive/Transmit RF Coils in
MR equipment (typically DC-6 GHz).
• The copper alloys of the body, springs and contact parts are designed to provide uniformity and maintain
low permeability and magnetic susceptibility.
• Gold finishes are altered to eliminate magnetic barrier layers and provide excellent corrosion resistance and
wear characteristics.
• Plugs maintain their electrical and mechanical performances in the environments of high-vibration common
with MRI machines.
• A robust connector assembly design allows for a high count of mating cycles.
• As a helpful visual cue the connectors are marked “NM”.
11
Mechanical Specifications
Emerson Connectivity Solutions Non-Magnetic design capabilities expand beyond the parts and interfaces listed in
this catalog. Please contact technical support to discuss the
options for manufacturing your customized interconnects.
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range: ............................................................................................................................ - 65°C to + 165°C
Thermal Shock:
MIL-STD-202, Method 107, Condition C (except -55° C to +155° C)
Corrosion:
MIL-STD-202, Method 101, Condition B
Shock:
MIL-STD-202, Method 213, Condition B
Vibration:
MIL-STD-202, Method 204, Condition D
Moisture Resistance: MIL-STD-202, Method 106
Material Specifications
(See non-magnetic materials page 10)
10
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MMCX CONNECTORS – NON-MAGNETIC - 50 OHM
Engagement Design: Series MMCX
Engagement/Disengagement Force: 8 lbs max axial engagement
1.4 lbs min axial disengagement
Contact Retention: 2.0 lbs min axial force
Axial Force* (lbs)
Torque (oz-in)
Cable Retention:
.047 flexible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5
N/A
RG-178 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0
N/A
RG-316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.0
N/A
RG-316 DS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.0
N/A
RG-405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.0 16
*Or cable breaking strength whichever is less.
Durability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 cycles min
MMCX CONNECTORS – NON-MAGNETIC - 50 OHM
Flexible Cable and PC Mount
Table of Contents
Right Angle Crimp Type Plug – Captivated Contact
Cable Type
Gold Plated
“A”
“B”
RG-316, 188, 187, 179, 161, 174
135-9403-101
.412 (10.46) .334 (8.48)
Crimp Sleeve
RG-178, 196
135-9402-111
.412 (10.46) .334 (8.48)
Crimp Sleeve
.047 OD Flexible
135-9436-101
.354 (8.99)
Crimp Insert
.276 (6.98)
Termination
Assembly instructions page 199 and 200.
Straight Crimp Type Plug – Solder or Crimp Contact – Captivated Contact
Cable Type
Gold Plated
“A”
“B”
Termination
RG-316, 188, 161, 174 135-9403-001
.509 (12.93)
.173 (4.39)
Crimp Sleeve
RG-178, 196
135-9402-001
.462 (11.73)
.137 (3.48)
Crimp Insert
.047 OD Flexible
135-9436-001
.462 (11.73)
.137 (7.01)
Crimp Insert
Assembly instructions page 204 and 205.
Straight Jack Receptacle
Gold Plated
“A”
135-9701-201
.115 (2.92)
135-9701-211
.068 (1.73)
Mounting hole layout figure 12 on page 195.
Right Angle Jack Receptacle
Gold Plated
“A”
135-9701-301
.155 (3.94)
135-9701-311
.068 (1.73)
MCX Connectors
50 Ohm Connectors
Specifications...........................................................14
Semi-Rigid & Flexible Cable......................................16
PC Mount.................................................................18
Bulkhead & Panel Mount......................................... 22
Adapters................................................................. 23
Terminations........................................................... 23
Reverse Polarity 50 Ohm Connectors
Specifications...........................................................24
Semi-Rigid & Flexible Cable..................................... 26
PC Mount................................................................ 27
75 Ohm Connectors
Specifications...........................................................28
Semi-Rigid & Flexible Cable......................................31
PC Mount.................................................................32
Adapters................................................................. 34
Terminiations...........................................................35
50 Ohm Non-Magnetic Connectors
Specifications.......................................................... 36
Semi-Rigid & Flexible Cable......................................37
PC Mount................................................................ 38
Other Information
Assembly Tools......................................................185
Capabilities............................................................190
Cable Information..................................................192
Assembly Instruction.............................................193
Mounting Hole Layouts..........................................194
Numerical Index.....................................................274
Competitor Cross Reference................................. 280
Packaging
135-9711-801
Stock
135-9711-802
Tape and Reel 1000 pcs/reel
Recommended land pattern figure 14 on page 195.
Tape and Reel .316 (8.0) component pitch .630 (16.0) wide.
MMCX Connectors
13
MCX Connectors
39
SMK Connectors
45
SMA Connectors
103
SMB Connectors
131
SMC Connectors
137
SMP Connectors
145
Type N Connectors
153
Shielded Cable Terminations
157
Between-Series Adapters
161
Fixed Length Cable Assemblies
173
Ultra Miniature Connectors (UMC)
181
kwiQMAte ™ Connectors
While every precaution has been taken to ensure accuracy and completeness
herein, Emerson Network Power Connectivity Solutions assumes no responsibility,
and disclaims all liability for damages resulting from use of this information or for
any errors or omissions. Specifications subject to change without notice.
193
Assembly Instructions
257
Electronic Hardware
274 Index
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
MCX CONNECTORS
End Launch Surface Mount Jack Receptacle
Gold Plated
3
185 Tools
Mounting hole layout figure 12 on page 195.
12
13
MCX CONNECTORS – 50 OHM
Specifications
Specifications
Electrical Specifications
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range:
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 165°C
Dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 125°C
Thermal Shock:
MIL-STD-202, Method 107, Condition F (N/A dummy loads)
Corrosion:
MIL-STD-202, Method 101, Condition B (N/A dummy loads)
Shock:
MIL-STD-202, Method 213, Condition B (N/A dummy loads)
Vibration:
MIL-STD-202, Method 204, Condition B (N/A dummy loads)
Moisture Resistance: MIL-STD-202, Method 106 (N/A dummy loads)
Material Specifications
Bodies:
Contacts:
Insulators:
Expansion Caps:
Crimp Sleeves:
Mounting Hardware:
Brass per ASTM B16, gold plated** per MIL-DTL-45204 .00001” min or
nickel plated per AMS-QQ-N-290
Male - brass per ASTM B16 , gold plated per MIL-DTL-45204 .00003” min
Female - beryllium copper per ASTM B196, gold plated per MIL-DTL-45204 .00003” min
PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457
Brass per ASTM B16 , gold plated per MIL-DTL-45204 .00001” min or nickel plated per AMS-QQ-N-290
Copper per ASTM B301, gold plated per MIL-DTL-45204 .00001” min
or nickel plated per AMS-QQ-N-290
Brass (nuts) per ASTM B16 or phosphor bronze (lockwashers) per ASTM B139,
gold plated per MIL-DTL-45204 .00001” min or nickel plated per AMS-QQ-N-290
** All gold plated parts include a .00005” min. nickel underplate barrier layer.
Mating Engagement for MCX Series Compatible with CECC 22220
1. ID of contact to meet VSWR mating characteristics and connector durability when mated
with a dia. .019-.021 (0.48-0.53) male contact.
2. Must meet the force to engage and disengage when mated with mating part.
† Avoid user injury due to misapplication. See safety advisory definitions inside front cover.
Mechanical Specifications
14
Engagement Design: Compatible with CECC 22220, Series MCX
Engagement Force:
5.6 lbs max axial force
Disengagement Force: 8 lbs max axial force, 1 lb min
Contact Retention:
2.3lbs min axial force (captivated contacts) 1 oz-in min torque (uncabled receptacles)
Axial Force* (lbs)
Torque (oz-in)
RG-178....................................................................................................................................10.0
N/A
RG-316....................................................................................................................................20.0
N/A
RG-316 DS...............................................................................................................................25.0
N/A
RG-405....................................................................................................................................30.0 16
*Or cable breaking strength whichever is less.
Durability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 cycles min
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 50 OHM
Impedance: 50 Ohms
Frequency Range:
Connectors............................................................................................................................................................0-6 GHz
Dummy loads........................................................................................................................................................0-1 GHz
VSWR: (max) (f = GHz)
Straight
Right Angle
Cabled Connectors Cabled Connectors
RG-178................................................................................................................................1.17 + .04f
1.07 + .06f
RG-316 and RG-405............................................................................................................1.13 + .04f
1.07 + .04f
Adapters...............................................................................................................................................................1.13 + .04f
Uncabled receptacles, Dummy loads................................................................................................................... N/A
Working Voltage: (VRMS max)†
Sea Level
70K Feet
RG-178................................................................................................................................. 250 65
RG-316, RG-405, uncabled receptacles, adapters............................................................... 335 85
Dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Dielectric Withstanding Voltage: (VRMS min at sea level)†
RG-178 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750
RG-316, RG-405, uncabled receptacles, adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
Dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Insulation Resistance: 1,000 megohms min
Contact Resistance: (milliohms max)
After
Initial
Environmental
Center contact (straight cabled connectors and uncabled receptacles)............................. 5.0 8.0
Center contact (right angle cabled connectors, adapters).................................................. 5.0 15.0
Outer contact (all connectors)............................................................................................ 1.0 1.5
Braid to body (gold plated connectors)............................................................................... 1.0
N/A
Braid to body (nickel plated connectors)............................................................................. 2.5
N/A
Corona Level: (Volts min at 70,000 feet)
RG-178 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
RG-316,RG-405 uncabled receptacles, adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Insertion Loss: (dB max tested at 1 GHz)
Straight cabled connectors, adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 dB
Right angle cabled connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 dB
Uncabled receptacles, dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 dB
Uncabled receptacles and adapters, dummy load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
RF High Potential Withstanding Voltage: (VRMS min, tested at 4 and 7 MHz)†
RG-178 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
RG-316 and adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
RG-405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
Dummy loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
Power Rating (Dummy Load): 0.5 watt @ +25°C, derated to 0.25 watt @ +125°C
15
MCX CONNECTORS – 50 OHM
Semi-Rigid Cable & Flexible Cable
Flexible Cable
Straight Solder Type Plug
17
Right Angle Crimp Type Plug – Captivated Contact
Cable Type
Gold Plated
Nickel Plated
RG-405
133-3693-001
133-3693-006
Assembly instructions page 206.
Right Angle Solder Type Plug – Captivated Contact
Cable Type
Gold Plated
Nickel Plated
Fig.
RG-178, 196
133-3402-101
133-3402-106
1
RG-316, 188, 161, 174
133-3403-101
133-3403-106
1
RG-316 DS, 188 DS
133-3404-101
133-3404-106
1
RG-58, 303, 141
133-3407-101
133-3407-106
2
RG-179, 187
133-3433-101
133-3433-106
1
Assembly instructions page 210.
Cable Type
Gold Plated
Nickel Plated
RG-405
133-3693-101
133-3693-106
Straight Crimp Type Jack – Solder or Crimp Contact
Assembly instructions page 206.
Straight Crimp Type Plug – Solder or Crimp Contact
Cable Type
Gold Plated
Nickel Plated
Captivated Contact
RG-178, 196
133-3302-001
133-3302-006
No
RG-316, 188, 161, 174, 179, 187 133-3303-001
133-3303-006
Yes
RG-316 DS, 188 DS
133-3304-006
Yes
133-3304-001
Assembly instructions page 207.
Cable Type
Gold Plated
Nickel Plated
Captivated Contact
RG-178, 196
133-3402-001
133-3402-006
No
RG-316, 188, 161, 174
133-3403-001
133-3403-006
Yes
RG-316 DS, 188DS
133-3404-001
133-3404-006
Yes
RG-179, 187
133-3433-001
133-3433-006
Yes
Straight Crimp Type Bulkhead Jack – Solder or Crimp Contact
Cable Type
Gold Plated
Nickel Plated
Captivated Contact
RG-178, 196
133-3302-401
133-3302-406
No
RG-316, 188, 161, 174, 179, 187
133-3303-401
133-3303-406
Yes
RG-316 DS, 188 DS
133-3304-401
133-3304-406
Yes
Assembly instructions page 207. Mounting hole layout figure 5 page 194.
16
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 50 OHM
Assembly instructions page 207.
MCX CONNECTORS – 50 OHM
PC Mount
PC Mount
Straight Plug Receptacle
19
Straight Jack Receptacle – .100” Layout
Gold Plated
Nickel Plated
Gold Plated
Nickel Plated
133-3701-231
133-3701-236
133-3801-201
133-3801-206
Mounting hole layout figure 12 page 194.
Mounting hole layout figure 4 page 194.
Straight Plug Receptacle – Low Profile
Straight Surface Mount Jack Receptacle
Gold Plated
Packaging
Gold Plated
Nickel Plated
133-3711-201
Stock
133-3801-211
133-3801-216
133-3711-202
Tape and Reel 750 pcs/reel
Mounting hole layout figure 4 page 194.
Recommended land pattern figure 13 on page 195.
Tape and Reel .315 (8.0) component pitch .630 (16.0) wide.
Straight Jack Receptacle
Straight Surface Mount Jack Receptacle
Nickel Plated
“A”
133-3701-201
133-3701-206
.155 (3.94)
Gold Plated
Packaging
133-3701-211
133-3701-216
.110 (2.79)
133-3711-211
Stock
133-3701-221
133-3701-226
.068 (1.73)
133-3711-212
Tape and Reel 750 pcs/reel
Mounting hole layout figure 4 page 194.
Four and six connector ganged receptacles available. See page 190.
18
Recommended land pattern figure 13 on page 195.
Tape and Reel .472 (12.0) component pitch .630 (16.0) wide.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 50 OHM
Gold Plated
MCX CONNECTORS – 50 OHM
PC Mount
PC Mount
Right Angle Jack Receptacle
End Launch Plug Receptacle
Gold Plated
Nickel Plated
“A”
133-3701-301
133-3701-306
.155 (3.94)
133-3701-311
133-3701-316
.110 (2.79)
Gold Plated
Nickel Plated
Board Thickness
“A”
“B”
133-3701-321
133-3701-326
.068 (1.73)
133-3801-841
133-3801-846
.062 (1.57)
.068 (1.73)
.048 (1.22)
133-3801-851
133-3801-856
.042 (1.07)
.048 (1.22)
.068 (1.73)
Mounting hole layout figure 4 page 194.
Right Angle Surface Mount Jack Receptacle
Gold Plated
Packaging
133-3711-301
Stock
133-3711-302
Tape and Reel 750 pcs/reel
Recommended land pattern figure 13 on page 195.
Tape and Reel .472 (12.0) component pitch .945 (24.0) wide.
Right Angle Surface Mount Jack Receptacle
End Launch Jack Receptacle
Gold Plated
Nickel Plated
Board Thickness
“A”
“B”
133-3701-801
133-3701-806
.062 (1.57)
.068 (1.73)
.048 (1.22)
133-3701-811
133-3701-816
.042 (1.07)
.048 (1.22)
.068 (1.73)
End Launch Bulkhead Jack Receptacle
Packaging
133-3711-311
Stock
Gold Plated
Nickel Plated
Board Thickness
133-3711-312
Tape and Reel 750 pcs/reel
133-3701-821
133-3701-826
.062 (1.57)
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 50 OHM
Gold Plated
Recommended land pattern figure 4 on page 194.
Tape and Reel .472 (12.0) component pitch .945 (24.0) wide.
20
21
MCX CONNECTORS – 50 OHM
PC Mount, Bulkhead Mount & Panel Mount
End Launch Surface Mount Jack Receptacle
Panel Mount, In-Series Adapters & Terminations
2-Hole Flange Mount Jack Receptacle – Extended Dielectric
Gold Plated
Packaging
133-3711-801
Stock
Gold Plated
Nickel Plated
“A”
“B”
133-3711-802
Tape and Reel 1000 pcs/reel
133-3701-611
133-3701-616
.170 (4.32)
.092 (2.34)
133-3701-621
133-3701-626
.300 (7.62)
.200 (5.08)
Recommended land pattern figure 21 page 195.
Tape and Reel .472 (12.0) component pitch .945 (24.0) wide
23
Jack to Jack Adapter
Front Mount Bulkhead Jack Receptacle
Gold Plated
Nickel Plated
Mounting Style
Fig
133-3701-401
133-3701-406
D Flat Threaded
1
133-3701-411
133-3701-416
Press Fit Knurl
2
Mounting hole layout for 133-3701-401 figure 5 page 194.
Mounting hole layout for 133-3701-406 figure 5 page 194.
Mounting hole layout for 133-3701-411 figure 10 page 194.
Mounting hole layout for 133-3701-416 figure 10 page 194.
2-Hole Flange Mount Jack Receptacle – Flush Dielectric
Gold Plated
Nickel Plated
133-3901-801
133-3901-806
Jack to Bulkhead Jack Adapter
Gold Plated
Nickel Plated
133-3901-401
133-3901-406
Mounting hole layout figure 5 page 194.
22
Gold Plated
Nickel Plated
133-3701-601
133-3701-606
Freq. Range
Gold Plated
Nickel Plated
Resistance
0-1 GHz
133-3801-801
133-3801-806
50 Ohm
0-1 GHz
133-3801-821
133-3801-826
75 Ohm
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 50 OHM
Plug Dummy Load
MCX CONNECTORS – REVERSE POLARITY – 50 OHM
Specifications
Specifications
Electrical Specifications
Material Specifications
Impedance: 50 Ohms
Frequency Range:.................................................................................................................................................0-6 GHz
VSWR (max): (f = GHz)
Straight
Right Angle
Cabled Connectors
Cabled Connectors
RG-178........................................................................................................................ 1.17 + .04f
1.07 + .06f
RG-316........................................................................................................................ 1.13 + .04f
1.07 + .04f
Uncabled receptacles..........................................................................................................................................N/A
Working Voltage: (VRMS max)†
Sea Level
70K Feet
RG-178 ........................................................................................................................ 250 65
RG-316 ........................................................................................................................ 335 85
Dielectric Withstanding Voltage: (VRMS min at sea level)†
RG-178 , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 750
RG-316, uncabled receptacles , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 1000
Corona Level: (Volts min at 70,000 feet)
RG-178 , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 190
RG-316, uncabled receptacles , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 250
Insertion Loss: (dB max tested at 1 GHz)
Straight cabled connectors , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 0.1 dB
Right angle cabled connectors , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 0.2 dB
Uncabled receptacles , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , N/A
Insulation Resistance: 1000 megohms min
Contact Resistance: (milliohms max)
After
Initial
Environmental
Center contact (straight cabled connectors and uncabled receptacles)...................... 5.0 8.0
Center contact (right angle cabled connectors)........................................................... 5.0 15.0
Outer contact (all connectors)..................................................................................... 1.0 1.5
Braid to body (gold plated connectors)........................................................................ 1.0
N/A
Braid to body (nickel plated connectors)...................................................................... 2.5
N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Cable connectors................................................................................................................................................-55 dB
Uncabled receptacles .........................................................................................................................................N/A
RF High Potential Withstanding Voltage: (VRMS min tested at 4 and 7 MHz) †
RG-178................................................................................................................................................................500
RG-316................................................................................................................................................................700
Uncabled receptacles..........................................................................................................................................600
Bodies:
Contacts:
Insulators:
Expansion Caps:
Crimp Sleeves:
Mounting Hardware:
Brass per ASTM B16 or zinc per ASTM B86-71, gold plated** per MIL-DTL-45204 .00001” min or
nickel plated per AMS-QQ-N-290
Male - brass per ASTM B16 , gold plated per MIL-DTL-45204 .00003” min
Female - beryllium copper per ASTM B196, gold plated per MIL-DTL-45204 .00003” min
PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457
Brass per ASTM B16 , gold plated per MIL-DTL-45204 .00001” min or nickel plated per AMS-QQ-N-290
Copper per ASTM B301, gold plated per MIL-DTL-45204 .00001” min or nickel plated per
AMS-QQ-N-290
Brass (nuts) per ASTM B16 or phosphor bronze (lockwashers) ASTM B139,
gold plated per MIL-DTL-45204
.00001” min or nickel plated per AMS-QQ-N-290
** All gold plated parts include a .00005” min. nickel underplate barrier layer.
Mechanical Specifications
Engagement Force:
5.6 lbs max axial force
Disengagement Force: 8 lbs max axial force, 1 lbs min.
Contact Retention:
2.3 lbs min axial force (captivated contacts) 1 oz-in min torque (uncabled receptacles)
Cable Retention:
Axial Force* (lbs)
Torque (oz-in)
RG-178........................................................................................................................................ 10.0
N/A
RG-316........................................................................................................................................ 20.0
N/A
RG-316 DS................................................................................................................................... 25.0
N/A
*Or cable breaking strength whichever is less.
Durability:...........................................................................................................................................................500 cycles min
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
24
Notes:
1. ID of contact to meet VSWR mating characteristics and connector durability when mated with a dia. .019-.021 (.48-.53) male contact.
2. Must meet the force to engage and disengage when mated with mating part.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – REVERSE POLARITY – 50 OHM
† Avoid user injury due to misapplication. See safety advisory definitions.
Temperature Range: .......................................................................................................................................... - 65°C to + 165°C
Thermal Shock:
MIL-STD-202, Method 107, Condition F
Corrosion:
MIL-STD-202, Method 101, Condition B
Shock:
MIL-STD-202, Method 213, Condition B
Vibration:
MIL-STD-202, Method 204, Condition B
Moisture Resistance: MIL-STD-202, Method 106
25
MCX CONNECTORS – REVERSE POLARITY – 50 OHM
Flexible Cable
PC Mount
Straight Crimp Type Plug – Solder or Crimp Contact
Cable Type
Gold Plated
Nickel Plated
Captivated Contact
RG-178, 196
133-5402-001
133-5402-006
No
RG-316, 188, 161, 174
133-5403-001
133-5403-006
Yes
RG-316 DS, 188 DS
133-5404-001
133-5404-006
Yes
Straight Jack Receptacle
Gold Plated
Nickel Plated
133-5701-201
133-5701-206
Mounting hole layout figure 4 page 194.
Assembly instructions page 207.
End Launch Bulkhead Jack Receptacle
Right Angle Crimp Type Plug – Captivated Contact
Gold Plated
Nickel Plated
133-5701-806
Gold Plated
Nickel Plated
133-5701-801
RG-178, 196
133-5402-101
133-5402-106
Mounting hole layout figure 4 page 194.
RG-316, 188, 161, 174
133-5403-101
133-5403-106
RG-316 DS, 188 DS
133-5404-101
133-5404-106
Straight Crimp Type Bulkhead Jack – Solder or Crimp Contact
Cable Type
Gold Plated
Nickel Plated
Captivated Contact
RG-178, 196
133-5302-401
133-5302-406
No
RG-316, 188, 161, 174
133-5303-401
133-5303-406
Yes
RG-316 DS, 188 DS
133-5304-401
133-5304-406
Yes
Mounting hole layout figure 5 page 194.
Assembly instructions page 207.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – REVERSE POLARITY – 50 OHM
Cable Type
Assembly instructions page 210.
26
27
MCX CONNECTORS – 75 OHM
Specifications
Specifications
Electrical Specifications
Mechanical Specifications
Impedance: 75 Ohms
Frequency Range:................................................................................................................................................... 0-6 GHz
VSWR : (max) (f = GHz)
Straight
Right Angle
Cabled Connectors Cabled Connectors
RG-179 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13 + .04f
1.07 + .04f
In-series adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.07 + .03f
Between-series adapters, loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.05 + .01f
Uncabled receptacles........................................................................................................................................... N/A
Working Voltage: (VRMS max)†
Sea Level
70K Feet
RG-179 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
85
Uncabled receptacles, adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
85
Loads, matching pad.............................................................................................................................................N/A
Dielectric Withstanding Voltage: (VRMS min at sea level)†
RG-179.................................................................................................................................................................. 1000
Uncabled receptacles, adapters............................................................................................................................ 1000
Loads..................................................................................................................................................................... N/A
Insulation Resistance: 1,000 megohms min
Contact Resistance: (milliohms max)
After
Initial
Environmental
Center contact (straight cabled connectors and uncabled receptacles)...........................5.0 8.0
Center contact (right angle cabled connectors, adapters)................................................10.0 15.0
Center contact (loads).......................................................................................................N/A
Outer contact....................................................................................................................1.0 1.5
Braid to body (gold plated connectors).............................................................................1.0
N/A
Corona Level: (Volts min at 70,000 feet) †
RG-179..................................................................................................................................................................250
Uncabled receptacles, adapters............................................................................................................................250
Loads matching pad..............................................................................................................................................N/A
Insertion Loss: (dB max tested at 1 GHz)
Straight cabled connectors................................................................................................................................... 0.1 dB
Right angle cabled connectors.............................................................................................................................. 0.2 dB
Uncabled receptacles, adapters............................................................................................................................N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Cable connectors..................................................................................................................................................-55 dB typical
Uncabled receptacles, adapters, loads .................................................................................................................N/A
RF High Potential Withstanding Voltage: (VRMS min, tested at 4 and 7 MHz)†
Cabled Connectors for RG-179............................................................................................................................. 700
Uncabled receptacles, adapters............................................................................................................................ 600
Loads..................................................................................................................................................................... N/A
Power Rating: (Loads) 1.0 Watt at +25°C, derated linearly to 0.5 Watts at +125°C
Engagement Design:
Compatible with CECC 22220, Series MCX 50 Ohm
Engagement Force:
5.6 lbs max axial force
Disengagement Force: 8 lbs max axial force, 1 lb min
Contact Retention:
2.3 lbs min axial force (captivated contacts) 1 oz-in - min torque (uncabled receptacles)
Axial Force (lbs) *
Torque (oz-in)
RG-179, BELDEN 735A......................................................................................................... 20.0
N/A
RG-179 DS............................................................................................................................ 25.0
N/A
*Or cable breaking strength whichever is less.
Durability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 cycles min
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range:
All Connectors, Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 165°C
Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 125°C
Thermal Shock:
MIL-STD-202, Method 107, Condition F (N/A Loads)
Temperature Coefficient: Loads +/- 300ppm/°C
Corrosion:
MIL-STD-202, Method 101, Condition B (N/A Loads)
Shock:
MIL-STD-202, Method 213, Condition B (N/A Loads)
Vibration:
MIL-STD-202, Method 204, Condition B (N/A Loads)
Moisture Resistance:
MIL-STD-202, Method 106 (N/A Loads)
Material Specifications
Bodies:
Contacts:
Insulators:
Expansion Caps:
Crimp Sleeves:
Mounting Hardware:
Brass per ASTM B16, gold plated** per MIL-DTL-45204 .00001” min or
stainless steel, type 303 per ASTM A582, passivated per MIL-F-14072 (EL70)
Male - brass per ASTM B16 , gold plated per MIL-DTL-45204 .00003” min
Female - beryllium copper per ASTM B196, gold plated per MIL-DTL-45204 .00003” min
PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457
Brass per ASTM B16 , gold plated per MIL-DTL-45204 .00001” min
Copper, gold plated per MIL-DTL-45204 .00001” min
Brass (nuts) per ASTM B16 or phosphor bronze (lockwashers) ASTM B139,
gold plated per MIL-DTL-45204 .00001” min
† Avoid user injury due to misapplication. See safety advisory definitions inside front cover.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 75 OHM
** All gold plated parts include a .00005” min. nickel underplate barrier layer.
28
29
MCX CONNECTORS – 75 OHM
Specifications
Mating Engagement for 75 Ohm MCX Series
(Intermatable with CECC22220 50 Ohm MCX)
1.
2.
3.
Flexible Cable
31
Straight Crimp Type Plug – Solder or Crimp Captivated Contact
ID of contact to meet VSWR mating characteristics and connector durability when
mated with a dia. .019-.021 (0.48-0.53) dia. male contact.
Must meet the force to engage and disengage when mated with mating part.
Interface shall intermiate with MCX 50 Ohm interface per CECC 22220.
Cable Type
Gold Plated
RG-179
133-8433-001
RG-179 DS
133-8434-001
Belden 735A
133-8445-001
Assembly instructions page 209.
Right Angle Crimp Type Plug – Captivated Contact
Cable Type
Gold Plated
Fig
RG-179
133-8433-101
1
RG-179 DS
133-8434-101
1
Belden 735A
133-8445-101
2
Assembly instructions page 211.
Straight Crimp Type Jack – Solder or Crimp Captivated Contact
Gold Plated
RG-179
133-8333-001
RG-179 DS
133-8334-001
Assembly instructions page 209.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 75 OHM
MCX CONNECTORS – 75 OHM
30
Cable Type
MCX CONNECTORS – 75 OHM
Straight Crimp Type Bulkhead Jack –
Solder or Crimp Captivated Contact
33
Right Angle Jack Receptacle
Gold Plated
“A”
Cable Type
Gold Plated
133-8701-301
.155 (3.80)
RG-179
133-8333-401
133-8701-311
.110 (2.70)
RG-179 DS
133-8334-401
Mounting hole layout figure 20 page 195.
Assembly instructions page 209.
Mounting hole layout figure 5 page 194.
Straight Plug Receptacle
Gold Plated
“A”
Cable Type
Board Thickness
133-8701-801
.062 (1.57)
133-8801-201
.155 (3.80)
.343 (8.71)
133-8801-211
.110 (2.70)
.343 (8.71)
133-8801-221
.155 (3.80)
.510 (12.95)
Straight Jack Receptacle
Gold Plated
“A”
133-8701-201
.155 (3.80)
133-8701-211
.100 (2.54)
End Launch Jack Receptacle
“B”
Mounting hole layout figure 20 page 195.
Surface Mount Jack Receptacle
Bulkhead Mount & In-Series Adapters
Bulkhead Jack Receptacle
Gold Plated
133-8701-401
Mounting hole layout figure 1 page 194.
Jack to Jack Adapter
Gold Plated
Packaging
Gold Plated
133-8711-201
Bulk Packs
133-8901-801
133-8711-202
Tape and Reel 770 pcs/reel
Mounting hole layout figure 11 page 194.
Tape and Reel .472 (12.0) component pitch .630 (16.0) wide.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 75 OHM
Mounting hole layout figure 20 page 195.
32
PC Mount
Flexible Cable & PC Mount
MCX CONNECTORS – 75 OHM
In-Series Adapters & Between Series Adapters
Jack to Plug Adapter
Between-Series Adapters & Terminations
75 Ohm Type N Jack to 75 Ohm MCX Plug Adapter
Gold Plated
Stainless Steel Passivated
133-8901-821
134-1068-021
75 Ohm Type N Plug to 75 Ohm MCX Plug Adapter
75 Ohm Type N Jack to 75 Ohm MCX Jack Adapter
Stainless Steel Passivated
Stainless Steel Passivated
134-1068-001
134-1068-031
75 Ohm Type N Plug to 75 Ohm MCX Jack Adapter
Plug Precision Load
Stainless Steel Passivated
Gold Plated
134-1068-011
133-8801-831
Gold Plated
133-8701-831
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – 75 OHM
Jack Precision Load
34
35
MCX CONNECTORS – NON-MAGNETIC – 50 OHM
Specifications
Non-Magnetic RF Connectors – For Flexible Cable
Electrical Specifications
Impedance: 50 Ohms
Frequency Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 GHz
VSWR (max): (f = GHz)
Straight
Right Angle
Cabled Connectors Cabled Connectors
RG-316 cable.................................................................................................................. 1.13 + .04f
1.07 + .04f
Uncabled receptacles..........................................................................................................................................N/A
Working Voltage: (VRMS max)†
Sea Level
70K Feet
RG-316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
85
Dielectric Withstanding Voltage: (VRMS min at sea level)†
RG-316, uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
Insulation Resistance: 1,000 megohms min
Contact Resistance: (milliohms max)
After
Initial
Environmental
Center contact (straight cabled connectors and uncabled receptacles)......................... 5.0 8.0
Center contact (right angle cabled connectors).............................................................. 5.0 15.0
Outer contact.................................................................................................................. 1.0 1.5
Braid to body................................................................................................................... 1.0
N/A
Corona Level: (Volts min at 70,000 feet) †
RG-316, uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Insertion Loss: (dB max tested at 1 GHz)
Straight cabled connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 dB
Right angle cabled connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 dB
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Cabled connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 dB
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
RF High Potential Withstanding Voltage: (VRMS min tested at 4 and 7 MHz)
Cabled Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
Straight Crimp Type Plug – Solder or Crimp Contact – Captivated Contact
Cable Type
Gold Plated
RG-316, 188, 174
133-9403-001
RG-316 DS, 188 DS
133-9404-001
Assembly instructions page 208.
Right Angle Crimp Type Plug – Captivated Contact
Cable Type
Gold Plated
RG-316, 188, 174
133-9403-101
RG-316 DS, 188 DS
133-9404-101
Assembly instructions page 207.
Mechanical Specifications
Engagement Design: Compatible with CECC 22220, Series MCX 50 Ohm
Engagement Force:
5.6 lbs max axial force
Disengagement Force: 8 lbs max axial force, 1 lb min
Contact Retention:
2.3 lbs min axial force (captivated contacts) 1 oz-in min torque (uncabled receptacles)
Axial Force (lbs) *
Torque (oz-in)
RG-316................................................................................................................................ 20.0
N/A
RG-316 DS........................................................................................................................... 25.0
N/A
*Or cable breaking strength whichever is less.
Durability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 cycles min
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range: ........................................................................................................................................... - 65°C to + 165°C
Thermal Shock:
MIL-STD-202, Method 107, Condition F
Corrosion:
MIL-STD-202, Method 101, Condition B
Shock:
MIL-STD-202, Method 213, Condition B
Vibration:
MIL-STD-202, Method 204, Condition B
Moisture Resistance: MIL-STD-202, Method 106
Material Specifications
(See non-magnetic materials page 10)
36
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
MCX CONNECTORS – NON-MAGNETIC – 50 OHM
† Avoid user injury due to misapplication. See safety advisory definitions.
37
MCX CONNECTORS – NON-MAGNETIC – 50 OHM
Non-Magnetic RF Connectors – For PC Mount
Table of Contents
Straight Jack Receptacle
Gold Plated
“A”
133-9701-201
.155 (3.94)
133-9701-211
.110 (2.79)
Mounting hole layout figure 4 page 194.
Straight Jack Receptacle – .100” Layout
SMK Connectors
3
MMCX Connectors
50 Ohm Connectors
Specifications.......................................................... 40
Semi-Rigid & Flexible Cable......................................43
Adapters................................................................. 44
13
MCX Connectors
39
SMK Connectors
45
SMA Connectors
103
SMB Connectors
131
SMC Connectors
137
SMP Connectors
145
Type N Connectors
153
Shielded Cable Terminations
157
Between-Series Adapters
161
Fixed Length Cable Assemblies
173
Ultra Miniature Connectors (UMC)
181
kwiQMAte ™ Connectors
Other Information
Assembly Tools......................................................185
Capabilities............................................................190
Cable Information..................................................192
Assembly Instruction.............................................193
Mounting Hole Layouts..........................................194
Numerical Index.....................................................274
Competitor Cross Reference................................. 280
Gold Plated
133-9701-231
Mounting hole layout figure 12 page 194.
Right Angle Jack Receptacle
Gold Plated
“A”
133-9701-301
.155 (3.94)
133-9701-311
.110 (2.79)
Mounting hole layout figure 4 page 194.
185 Tools
While every precaution has been taken to ensure accuracy and completeness
herein, Emerson Network Power Connectivity Solutions assumes no responsibility,
and disclaims all liability for damages resulting from use of this information or for
any errors or omissions. Specifications subject to change without notice.
Gold Plated
Board Thickness
133-9701-801
.062 (1.57)
193
Assembly Instructions
257
Electronic Hardware
274 Index
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
SMK CONNECTORS
End Launch Jack Receptacle – Round Contact
38
39
SMK CONNECTORS – 50 OHM
Specifications
SMK (2.92mm) Connectors
The Johnson line of SMK Connectors provides an excellent solution for
demanding applications requiring high frequency transmission. Although
similar to the SMA interface, a smaller internal body diameter (2.92mm) and
air dielectric provide a higher cutoff frequency and other key advantages:
• Precision manufacturing allows superior electrical performance to 40 GHz
• Female contacts have a unique three-slot construction, which enhances
connectivity by creating a more rugged connector while reducing the
chance of intermittent connections
• Precise assembly tooling assures excellent, repeatable contact and
support bead location on cabled connectors
• Connector mating interface per MIL-STD-348
• Mating interface control provides consistent electrical performance
• Plug connector VSWR is 1.20 Max to 40 GHz and a 12 inch SMK plug to plug cable assembly performs better than 1.35
VSWR to 40 GHz
• Field Replaceable Jacks are teamed with a high quality hermetic seal feed thru for use in sealed circuit modules
• SMK plug interface employs more precise dimensions than an SMA and uses a shorter snub nose male pin such that the
connector bodies align before the contacts engage
Electrical Specifications
Specifications
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-C-39012)
Temperature Range: - 65°C to + 165°C
Thermal Shock: MIL-STD-202, Method 107, Condition B
Corrosion: MIL-STD-202, Method 101, Condition B
Shock: MIL-STD-202, Method 213, Condition I
Vibration: MIL-STD-202, Method 204, Condition D
Moisture Resistance: MIL-STD-202, Method 106
Material Specifications
Bodies: Stainless steel per ASTM B16, gold plated* per MIL-G-45204 .00005” min. or passivated per MIL-DTL-14072
Contacts: Female - beryllium copper per ASTM B1960, gold plated per MIL-DTL- G-45204 .00005” min
Contact Support Beads: PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457 or modified PPE resin
Seal Rings: Silicone rubber per ZZ-R-765
* All gold plated parts include a .00005” min. nickel underplate barrier layered
Impedance:
50 Ohms
Frequency Range: 0-40 GHz
VSWR (max): (f = GHz)
Semi-Rigid straight cabled connectors and adapters.......................................................................................... 1.20 max
Field replaceable (see typical return loss graph).................................................................................................. N/A
Working Voltage: (VRMS max)
Connectors for Cable Type
Sea Level
70K Feet
RG-405 and field replaceable..................................................................................................... 335
85
RG-402 and adapters................................................................................................................. 500
125
Dielectric Withstanding Voltage: (VRMS min at sea level)
RG-405 and field replaceable.............................................................................................................................. 1000
RG-402 and adapters.......................................................................................................................................... 1500
Corona Level: (Volts min at 70,000 feet)
RG-405 and field replaceable............................................................................................................................... 250
RG-402 and adapters........................................................................................................................................... 375
Insertion Loss: (dB max)
Adapters .................................................................................................................................... 0.06 f (GHz), tested at 6 GHz
Straight Semi-Rigid cable connectors ........................................................................................ 0.03 f (GHz), tested at 10 GHz
Insulation Resistance: 5000 megohms min
Contact Resistance: (milliohms max)
Initial After Environmental
Center contact straight cabled connectors ............................................................................ 3.0*
4.0
Center contact adapters............................................................................................................ 4.0
6.0
Field replaceable connectors..................................................................................................... 6.0
8.0
Outer contact (all connectors)................................................................................................... 2.0
N/A
Body to cable (gold plated connectors)..................................................................................... 0.5
N/A
Body to cable (passivated connectors)...................................................................................... 5.0
N/A
RF Leakage: (dB min, tested at 2.5 GHz) ............................................................................................................... -90dB
RF High Potential Withstanding Voltage: (VRMS min., tested at 4 and 7 MHz)†
RG-405 and field replaceable............................................................................................................................... 670
RG-402 and adapters........................................................................................................................................... 1000
Mating Engagement for SMK (2.92mm) Series
40
† Avoid user injury due to misapplication. See safety advisory definitions.
Notes:
1. ID of contact shall meet VSWR and connectivity requirements when mated with dia. .0355-.0365 male pin.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMK CONNECTORS – 50 OHM
Mechanical Specifications
Engagement Design:
MIL-STD-348, Series SMK (2.92mm)
Engagement/Disengagement Force: 2 lb-in max
Mating Torque:
7 to 10 in-lb
Bulkhead Mounting Nut Torque:
15 in-lb
Coupling Proof Torque:
15 in-lb min
Coupling Nut Retention:
60 lbs min
Contact Retention:
6 lbs min axial force (captivated contacts)
Cable Retention:
Axial Force* (lbs) Torque (in-oz)
RG-405.......................................................................................................................................30 16
RG-402.......................................................................................................................................60 55
*Or cable breaking strength whichever is less
Durability: 500 cycles min
41
SMK CONNECTORS – 50 OHM
Specifications
Field Replaceable Application Notes
Semi-Rigid Cable
Straight Solder Type Plug – with Contact, Slide-On Nut
These field replaceable connectors are easy to install and replace. The hermetic seal is mounted into the circuit module
wall and the connector can be removed and replaced without destroying the hermeticity of the circuit housing.
The field replaceable connector creates a transition from microstrip circuitry to a coaxial transmission line. The SMK
(2.92mm) seal pin diameter is .012 (.030) to minimize the capacitive effects on the circuit trace. For optimum electrical
performance, the transition from the hermetic seal to the microstrip trace must be properly compensated which involves
adjusting the microstrip trace width to minimize any impedance discontinuities found in the transition area.
The plot shown below is representative of the typical return loss of a Johnson field replaceable SMK connector. To produce the data shown below, a test fixture is created using the Johnson SMK hermetic seal. The fixture consists of a suitably thick spacer plate with the hermetic seal mounted flush to both surfaces. Two connectors are mounted back to back
around the fixture and the VSWR of this test assembly is measured. The calculated return loss trace shown is equivalent
to the square root of the measured VSWR of the test assembly. Since the connectors tested are of identical design, it can
be stated with fair accuracy that the calculated data shown represents the response of a single field replaceable connector and its transition to the hermetic seal.
Although we do not publish a VSWR specification for field replaceable connectors, typical connector return loss can
be expected to be better than 20 dB through 40 GHz. A VSWR specification is not stated because an industry standard
method for testing field replaceable connectors does not exist. The actual performance of the connector is dependent
upon the following:
1. For optimum electrical performance, we recommend the use of our standard 142-1000-033 hermetic seal with a pin
diameter of .0120+/-.0005 (0.305+/-0.013).
2. It is recommended that the hermetic seal be mounted flush with the circuit housing. Tolerance variations between the
hermetic seal and machined housing do not always guarantee an optimum transition to the connector. Some manufacturers recommend an additional counterbore in the circuit housing to accommodate a solder washer during installation of the seal. We do not recommend this type of installation because, if the counterbore is not completely filled
with solder, electrical discontinuities may be created.
3. The transition between the hermetic seal pin and the microstrip trace will effect electrical performance, as stated
above. Several different methods of hermetic seal mounting and seal pin to microstrip trace attachment are used in
the industry.
Cable Type
Gold Plated
Passivated*
RG-405 RG-402
145-0693-001
145-0693-002
RG-405 RG-402
145-0694-001
145-0694-002
Assembly instructions page 212.
*Passivated coupling nut with gold plated body.
2-Hole Flange Mount Jack Receptacle
Gold Plated
Passivated
145-0701-601 145-0701-602
Accepts Pin Size
Mounting hole layout
.0120+/-.0005(0.305+/-0.013)
4-Hole Flange Mount Jack Receptacle
Gold Plated
Passivated
145-0701-611 145-0701-612
Accepts Pin Size
Mounting hole layout
.0120+/-.0005(0.305+/-0.013)
Gold Plated
Passivated
Accepts Pin Size
145-0701-001
145-0701-002
.0120 +/-.0005 (0.305 +/-0.013)
Mounting hole layout
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMK CONNECTORS – 50 OHM
Jack Receptacle – Thread Mount Field Replaceable
42
43
SMK CONNECTORS – 50 OHM
Table of Contents
In-Series Adapters
Hermetic Seal Feedthru
SMA Connectors
Part No.
Item 1 – Outer Ring
Item 2 – Insulator
Item 3 – Pin
142-1000-033
Kovar
Gold Pl .00005 min over
Nickel Pl .00005 min
Glass
Corning 7070
Or Equivalent
Kovar
Gold Pl .00005 min. over
Nickel Pl .00005 min.
Notes:
1. The hermetic seal should be mounted as flush as possible with the housing. Excessive recession will create a high impedance air gap
between connection and housing which degrades electrical performance.
2. The use of an additional counterbore to accommodate a solder ring for seal mounting is not recommended. A slight chamfer may
be used if care is taken to completely fill the area with solder. Avoid air gaps!
Electrical
Environmental
Impedance:
50 Ohms
Frequency Range:
DC to 40 GHz
VSWR:
Dependent upon application
Working Voltage:
250 VRMS max at sea level
Dielectric Withstanding Voltage: 500 VRMS min at sea level
Insulation Resistance:
5000 Megohm min
Insertion Loss:
0.2 dB max at 40 GHz
Hermeticity:
1x10-8 cc/sec at one atmosphere
Solderability:
MIL-STD-202, Method 209
Operating Temperature: -55° C to +165° C
Jack to Jack In-Series Adapter
Gold Plated
145-0901-801
Plug to Plug In-Series Adapter
Gold Plated
145-0901-811
While every precaution has been taken to ensure accuracy and completeness
herein, Emerson Network Power Connectivity Solutions assumes no responsibility,
and disclaims all liability for damages resulting from use of this information or for
any errors or omissions. Specifications subject to change without notice.
3
MMCX Connectors
13
MCX Connectors
39
SMK Connectors
45
SMA Connectors
103
SMB Connectors
131
SMC Connectors
137
SMP Connectors
145
Type N Connectors
153
Shielded Cable Terminations
157
Between-Series Adapters
161
Fixed Length Cable Assemblies
173
Ultra Miniature Connectors (UMC)
181
kwiQMAte ™ Connectors
185 Tools
193
Assembly Instructions
257
Electronic Hardware
274 Index
Gold Plated
145-0901-821
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
SMA CONNECTORS
50 Ohm Connectors
Specifications.......................................................... 46
Quick Connect........................................................ 49
Semi-Rigid & Flexible Cable..................................... 50
PC Mount................................................................ 56
Bulkhead & Panel Mount......................................... 62
Self-Fixture End Launch........................................... 63
Field Replaceable.....................................................71
Adapters..................................................................76
Terminations........................................................... 77
Reverse Polarity
Specifications...........................................................78
Semi-Rigid & Flexible Cable..................................... 80
PC Mount.................................................................81
Reverse Thread
Specifications.......................................................... 82
Semi-Rigid & Flexible Cable..................................... 83
PC Mount................................................................ 85
50 Ohm Non-Magnetic Connectors
Specifications.......................................................... 86
Semi-Rigid & Flexible Cable..................................... 87
PC Mount................................................................ 88
50 Ohm High Frequency End Launch
Specifications.......................................................... 90
PC Mount.................................................................92
50 Ohm Stainless Steel
Specifications.......................................................... 94
Semi-Rigid & Flexible Cable..................................... 97
PC Mount...............................................................100
Bulkhead & Panel Mount........................................100
Fixed Attenuators
Specifications.........................................................102
Attenuators........................................................... 113
Other Information
Assembly Tools......................................................185
Capabilities............................................................190
Cable Information..................................................192
Assembly Instruction.............................................193
Mounting Hole Layouts..........................................194
Numerical Index.....................................................274
Competitor Cross Reference................................. 280
Plug to Jack In-Series Adapter
44
45
SMA CONNECTORS – 50 OHM
Specifications
Electrical Ratings
Insertion Loss: (dB max)
Straight flexible cable connectors and adapters......................................................................0.06
Right angle flexible cable connectors......................................................................................0.15
Straight Semi-Rigid cable connectors with contact ................................................................0.03
Right angle Semi-Rigid cable connectors................................................................................0.05
Straight Semi-Rigid cable connectors w/o contact .................................................................0.03
Straight low loss flexible cable connectors..............................................................................0.06
Right Angle low loss flexible cable connectors........................................................................0.15
f (GHz),
f (GHz),
f (GHz),
f (GHz),
f (GHz),
f (GHz),
f (GHz),
tested at 6 GHz
tested at 6 GHz
tested at 10 GHz
tested at 10 GHz
tested at 16 GHz
tested at 1 GHz
tested at 1 GHz
Uncabled receptacles, field replaceable, dummy loads.................................................................................................... N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Flexible cable connectors, adapters and RG-402 connectors w/o contact...................................................................... -60 dB
Field replaceable w/o EMI gasket..................................................................................................................................... -70 dB
RG-405 connectors and RG-402 connectors with contact, and field replaceable with EMI Gasket................................. -90 dB
Two-way adapters........................................................................................................................................................... -90 dB
Uncabled receptacles, dummy loads...............................................................................................................................N/A
RF High Potential Withstanding Voltage:
(VRMS min, tested at 4 and 7 MHz)†
RG-178.............................................................................................................................................................................. 335
RG-316, LMR-100, 195, 200.............................................................................................................................................. 500
RG-58, RG-142, LMR-240, RG-405, RG-402 connectors w/o contact, uncabled receptacles........................................... 670
RG-402 with contact and adapters................................................................................................................................... 1000
Power Rating (Dummy Load): 0.5 watt @ + 25°C, derated to 0.25 watt @ +125°C
Mechanical Ratings
Engagement Design:
MIL-STD-348, Series SMA
Engagement/Disengagement Force: 2 lb-in max
Mating Torque:
7 to 10 lb-in
Bulkhead Mounting Nut Torque:
15 lb-in
Coupling Proof Torque:
15 lb-in min
Coupling Nut Retention:
60 lbs min
Contact Retention:
6 lbs min axial force (captivated contacts)
4 oz-in min torque (uncabled receptacles)
Cable Retention:............................................................................................................. Axial Force* (lbs)
Torque (oz-in)
RG-178......................................................................................................................................10
N/A
RG-316, LMR-100......................................................................................................................20
N/A
LMR-195, 200...........................................................................................................................30
N/A
RG-58, LMR-240........................................................................................................................40
N/A
RG-142......................................................................................................................................45
N/A
RG-405......................................................................................................................................30 16
RG-402......................................................................................................................................60 55
*Or cable breaking strength whichever is less.
Durability: 500 cycles min 100 cycles min for RG-402 connectors w/o contact
Environmental Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range:
Thermal Shock:
Corrosion:
Shock:
Vibration:
Moisture Resistance:
- 65°C to + 165°C
MIL-STD-202, Method 107, Condition B (N/A dummy loads)
MIL-STD-202, Method 101, Condition B (N/A dummy loads)
MIL-STD-202, Method 213, Condition I (N/A dummy loads)
MIL-STD-202, Method 204, Condition Dv
MIL-STD-202, Method 106 (N/A dummy loads)
† Avoid user injury due to misapplication. See safety advisory definitions.
46
47
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Impedance: 50 Ohms
Frequency Range:
Dummy loads........................................................................................................................................................0-2.00 GHz
Flexible cabled connectors....................................................................................................................................0-12.4 GHz
Uncabled receptacles, Right Angle Semi-Rigid cabled connectors and adapters..................................................0-18.0 GHz
Straight Semi-Rigid cabled connectors and field replaceable connectors ............................................................0-26.5 GHz
VSWR : (max) (f = GHz)
Straight
Right Angle
Cabled Connectors
Cabled Connectors
RG-178............................................................................................................................. 1.20 + .025f
1.20 + .03f
RG-316, LMR-100............................................................................................................. 1.15 + .02f
1.15 + .03f
RG-58, LMR-195............................................................................................................... 1.15 + .01f
1.15 + .02f
RG-142............................................................................................................................. 1.15 + .01f
1.15 + .02f
LMR-200, LMR-240.......................................................................................................... 1.10 + .03f
1.10 + .06f
RG-405............................................................................................................................. 1.07 + .008f
1.18 + .015f
RG-402 (w/contact)......................................................................................................... 1.05 + .008f
1.15 + .015f
RG-402 (w/o contact)...................................................................................................... 1.035 + .005f
Jack-bulkhead jack adapter and plug-plug adapter.............................................................................................. 1.05 + .010f
Jack-jack adapter and plug-jack adapter............................................................................................................... 1.05 + .005f
Uncabled receptacles, dummy loads..................................................................................................................... N/A
Field replaceable (see page 80).............................................................................................................................. N/A
Working Voltage: (VRMS max)†
Sea Level
70K Feet
RG-178............................................................................................................................ 170 45
RG-316, LMR-100, 195, 200............................................................................................ 250 65
RG-58, RG-142, LMR-240, RG-405, uncabled receptacles, RG-402 w/o contact............ 335 85
RG-402 with contact and adapters.................................................................................. 500
125
Dummy loads.........................................................................................................................................................N/A
Dielectric Withstanding Voltage: (VRMS min at sea level)†
RG-178.................................................................................................................................................................. 500
RG-316, LMR-100, 195, 200 ................................................................................................................................ 750
RG-58, RG-142, LMR-240, RG-405, field replaceable, uncabled receptacles........................................................ 1000
RG-402 with contact and adapters....................................................................................................................... 1500
RG-402 w/o contact, dummy loads...................................................................................................................... N/A
Insulation Resistance: 5000 megohms min
Contact Resistance: (milliohms max)
Initial
After Environmental
Center contact (straight cabled connectors and uncabled receptacles)........................ 3.0*
4.0*
Center contact (right angle cabled connectors and adapters).........................................4.0 6.0
Field replaceable connectors............................................................................................6.0 8.0
Outer contact (all connectors)..........................................................................................2.0
N/A
Braid to body (gold plated connectors)............................................................................0.5
N/A
Braid to body (nickel plated connectors)..........................................................................5.0
N/A
*N/A where the cable center conductor is used as a contact
Corona Level: (Volts min at 70,000 feet)†
RG-178.................................................................................................................................................................. 125
RG-316, LMR-100, 195, 200.................................................................................................................................. 190
RG-58, RG-142, LMR-240, RG-405, uncabled receptacles, RG-402 w/o contact.................................................. 250
RG-402 with contact and adapters........................................................................................................................ 375
Dummy loads........................................................................................................................................................ N/A
Specifications
SMA CONNECTORS – 50 OHM
Quick Connect
Specifications
Material Specifications
Bodies:
Contacts:
Nut Retention Spring:
Insulators:
Expansion Caps:
Crimp Sleeves:
Mounting Hardware:
Seal Rings:
EMI Gaskets:
Brass per ASTM B16, gold plated* per MIL-DTL-45204 .00001” min. or nickel plated per SAE-AMS2423
Male - brass per ASTM B16, gold plated per MIL-DTL-45204 .00005” min
Female - beryllium copper per ASTM B196, gold plated per MIL-DTL-45204 .00005” min
Beryllium copper per ASTM B196, Unplated
PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457 or Tefzel per ASTM D 3159 or
PFA 340 per ASTM D 3307
Brass per ASTM B36, gold plated per MIL-DTL-45204 .00001” min. or nickel plated per SAE-AMS2423
Copper per ASTM B301 or brass per ASTM B16, gold plated per MIL-DTL-45204 .00001” min
or nickel plated per SAE-AMS2423
Brass (nuts) per ASTM B16 or phosphor bronze (lockwashers), gold plated per
MIL-DTL-45204 .00005” min or nickel plated per SAE-AMS2423
Silicone rubber per A-A-59588A
Conductive silicone rubber per MIL-G-83528, Type M
* All gold plated parts include a .00005” min. nickel underplate barrier layer
Mating Engagement for SMA Series
49
The Johnson line of SMA Quick-Connect Plug quickly mates to a
standard, threaded SMA Jack receptacle allowing rapid test connections to devices utilizing SMA threaded jacks.
SMA electrical performance is not compromised because the connector retains all the benefits of a threaded coaxial coupling. The
final connection is a solid metal to metal coupling not relying on
spring forces to maintain the coupling. This results in a more reliable
connection with less signal leakage and a lower VSWR than most
push-on connectors.
Full MIL-PRF-39012 electrical compatibility is obtained with a push
and twist motion. The knurled thumbnut requires only one half to
one full turn to create a solid electromechanical connection. Rapid
disconnect is accomplished with a twist and pull motion.
The SMA Quick-Connect Plug Adapter converts a standard SMA
Plug test cable into a Quick-Connect cable. This makes the testing
process more efficient by reducing the time and effort required to
connect and disconnect the test cable.
Note: Push-on using front of connector, twist back-end coupling nut
to secure.
Adapters
Plugs
Cable Type
Gold Plated*
“A”
Gold Plated*
RG-161, 174, 188, 316
142-1403-001
1.249
142-1901-821
RG-188 DS, RG-316 DS
142-1404-001
1.249
RG-58, 141, 303
142-1407-001
1.099
RG-55, 142, 223, 400
142-1408-001
1.249
*Nickel plated coupling hardware, gold plated body
Assembly instructions page 219.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
48
SMA CONNECTORS – 50 OHM
Semi-Rigid Cable
Semi-Rigid Cable
51
Straight Solder Type Plug – with Contact, Thread-on Nut
Straight Solder Type Plug – with Contact,
Captive Nut Thin Wall Connector Interface
Cable Type
Gold Plated
Nickel Plated
“A”
RG-405
142-0693-051
142-0693-056
.405 (10.29)
142-0694-051
142-0694-056
.438 (11.13)
Cable Type
Gold Plated
Nickel Plated
Fig.
“A”
RG-402
RG-405
142-0693-001
142-0693-006
1
.405 (10.29)
Assembly instructions page 216.
RG-402
142-0694-001* 142-0694-006*
2
.440 (11.18)
Assembly instructions page 214.
*Mating torque 8 lb-in max, coupling proof torque 8 lb-in max.
Straight Solder Type Plug – Short Profile – without Contact, Captive Nut
Straight Solder Type Plug – without Contact, Thread-on Nut
Cable Type
Gold Plated
Nickel Plated
RG-402
142-0694-031
142-0694-036
Assembly instructions page 215. Center conductor of cable serves as contact.
Cable Type
Gold Plated
Nickel Plated
RG-402
142-0694-011
142-0694-016
Straight Solder Type Plug – without Contact, Slide-on Nut
Assembly instructions page 214.
Center conductor of cable serves as contact.
Right Angle Solder Type Plug (1-piece body)
Cable Type
Gold Plated
Nickel Plated
RG-402
142-0694-021
142-0694-026
Assembly instructions page 215.
Center conductor of cable serves as contact.
Gold Plated
Nickel Plated
“A”
“B”
RG-405
142-0693-101
142-0693-106
.336 (8.53)
.253 (6.43)
RG-402
142-0694-101
142-0694-106
.462 (11.73)
.306 (7.77)
Straight Solder Type Plug – without Contact, Slide-on Notched Nut
Assembly instructions page 213.
Cable Type
Gold Plated
Nickel Plated
RG-402
142-0694-041
142-0694-046
Assembly instructions page 215. Center conductor of cable serves as contact.
50
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Cable Type
SMA CONNECTORS – 50 OHM
Semi-Rigid Cable
Flexible Cable
Straight Solder Type Jack
Cable Type
Gold Plated
53
Straight Crimp Type Plug (3-piece) – Solder or Crimp Captivated Contact
Nickel Plated
Cable Type
Gold Plated
Nickel Plated
“A”
142-0402-011
142-0402-016
.591 (15.01)
RG-405
142-0593-001
142-0593-006
RG-178, 196
RG-402
142-0594-001
142-0594-006
RG-161, 174,188, 316, LMR-100 HPF-100 RF-100
142-0403-011
142-0403-016
.706 (17.93)
RG-188 DS, RG-316 DS
142-0404-011
142-0404-016
.706 (17.93)
RG-58, 141, 303, LMR-195, HPF-195, RF-195
142-0407-011
142-0407-016
.706 (17.93)
RG-55, 142, 223, 400
142-0408-011
142-0408-016
.706 (17.93)
RG-179, 187
142-0433-011
142-0433-016
.706 (17.93)
LMR-200, HPF-200, RF-200
142-0439-001
142-0439-006
.844 (21.44)
LMR-240, HPF-240, RF-240
142-0435-001
142-0435-006
.844 (21.44)
Assembly instructions page 214.
Straight Solder Type Bulkhead Jack with O-Ring
Assembly Instructions: RG-178 page 217. LMR 195, 200 and 240, see page 220.
Other cable groups, see page 219.
Cable Type
Gold Plated
Nickel Plated
RG-405
142-0593-401
142-0593-406
RG-402
142-0594-401
142-0594-406
Right Angle Crimp Type Plug – Captivated Contact
Assembly instructions page 214.
Mounting hole layout figure 1 page 194.
Straight Solder Type Bulkhead Jack
Cable Type
Gold Plated
RG-405
142-0593-411
Gold Plated
Nickel Plated
“A”
“B”
142-0402-101
142-0402-106
.611 (15.52)
.470 (11.94)
R-161, 174,188, 316, LMR-100, HPF-100, RF-100
142-0403-101
142-0403-106
.611 (15.52)
.470 (11.94)
RG-188 DS, RG-316 DS
142-0404-101
142-0404-106
.611 (15.52)
.470 (11.94)
LMR-195, HPF-195, RF-195, RG-58, 141, 303
142-0407-101
142-0407-106
.611 (15.52)
.470 (11.94)
RG-55, 142, 223, 400
142-0408-101
142-0408-106
.611 (15.52)
.470 (11.94)
RG-179, 187
142-0433-101
142-0433-106
.611 (15.52)
.470 (11.94)
LMR-200, HPF-200, RF-200
142-0439-101
142-0439-106
.611 (15.52)
.470 (11.94)
LMR-240, HPF-240, RF-240
142-0435-101
142-0435-106
.635 (16.13)
.490 (12.45)
Assembly Instructions: LMR 195, 200 and 240 page 229.
Other cable groups, see page 224.
52
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Assembly instructions page 214.
Mounting hole layout figure 1 page 194.
.073
2.36)
Cable Type
RG-178, 196
SMA CONNECTORS – 50 OHM
Flexible Cable
Flexible Cable
Straight Crimp Type Bulkhead Jack – Captivated Contact
Cable Type
Gold Plated
Straight Clamp Type Plug – Captivated Contact
Nickel Plated
Cable Type
Gold Plated
Nickel Plated
“A”
142-0202-011
142-0202-016
.816 (20.73)
RG-178, 196
142-0302-401
142-0302-406
RG-178, 196
RG-161, 174,188, 316
142-0303-401
142-0303-406
RG-161, 174, 188, 316
142-0203-011
142-0203-016
.816 (20.73)
RG-188 DS, RG-316 DS
142-0304-401
142-0304-406
RG-58, 141, 303, 55, 142, 223, 400
142-0207-011
142-0207-016
.895 (22.73)
RG-58, 141, 303
142-0307-401
142-0307-406
RG-55, 142, 223, 400
142-0308-401
142-0308-406
Assembly instructions page 230.
Mounting hole layout figure 1 page 194.
Assembly instructions page 225.
Mounting hole layout figure 1 page 194.
55
Right Angle Clamp Type Plug – Captivated Contact
Straight Crimp Type Bulkhead Jack (3-piece) – Solder or Crimp Captivated Conact
Cable Type
Gold Plated
Nickel Plated
“A”
RG-178, 196
142-0302-431
142-0302-436
.285 (7.24)
RG-161, RG-16, 174,188, 316,
LMR-100 HPF-100 RF-100
142-0303-411
142-0303-416
.385 (9.78)
RG-188 DS, RG-316 DS
142-0304-411
142-0304-416
.385 (9.78)
RG-58, 141, 303,
LMR-195, HPF-195, RF-195
142-0307-411
142-0307-416
.385(9.78)
RG-55, 142, 223, 400
142-0308-411
142-0308-416
.385 (9.78)
RG-179, 187
142-0333-411
142-0333-416
.385 (9.78)
LMR-200, HPF-200, RF-200
142-0339-401
142-0339-406
.545 (13.84)
LMR-240, HPF-240, RF-240
142-0335-401
142-0335-406
.545 (13.84)
Assembly Instructions: RG-178 page 217. LMR 195, 200 and 240, see page 220.
Other cable groups, see page 219. Mounting hole layout figure 1 page 194.
Gold Plated
Nickel Plated
“A”
“B”
RG-178 196
142-0202-101
142-0202-106 .569 (14.45) .428 (10.81)
RG-161 174, 188,316
142-0203-101
142-0203-106 .574 (14.58) .433 (11.00)
RG-58, 141, 303, 55,
142, 223, 400
142-0207-101
142-0207-106 .686 (17.42) .545 (13.84)
Assembly instructions page 231.
Mounting hole layout figure 1 page 194.
Straight Clamp Type Bulkhead Jack – Captivated Contact
Cable Type
Gold Plated
Nickel Plated
“A”
RG-178, 196
142-0102-401
142-0102-406
.452 (11.48)
RG-161, 174, 188, 316
142-0103-401
142-0103-406
.487 (12.37)
RG-58, 141, 303, 55, 142, 223, 400
142-0107-401
142-0107-406
.531 (13.49)
Assembly instructions page 230.
Rear Mount Bulkhead Plug – Antenna Connector
54
Cable Type
Gold Plated
Nickel Plated
“A”
RG-178, 196
142-0302-011
142-0302-016
.651 (16.54)
RG-161, 174,188, 316
142-0303-011
142-0303-016
.756 (19.20)
RG-188 DS, RG-316 DS
142-0304-011
142-0304-016
.756 (19.20)
RG-58, 141, 303
142-0307-011
142-0307-016
.756 (19.20)
RG-55, 142, 223, 400
142-0308-011
142-0308-016
.756 (19.20)
Assembly Instructions: RG-178 page 217. LMR 195, 200 and 240, see page 220.
Other cable groups, see page 219. Mounting hole layout figure 1 page 194.
Cable Type
Gold Plated
RG-178, .047 Semi-Rigid
142-0801-421*
* With Nickel mounting nut. Assembly instructions page 216.
Mates with SMA Jack Antenna Interface.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Straight Crimp Type Jack (3-piece) – Solder or Crimp Captivated Contact
Cable Type
SMA CONNECTORS – 50 OHM
PC Mount
PC Mount
Straight Jack Receptacle – Surface Mount
Straight Plug Receptacle
Gold Plated
Nickel Plated
142-0801-201
142-0801-206
57
Gold Plated
Packaging
142-0711-201
Stock
142-0711-202
Tape and Reel 500 pcs/reel
Mounting hole layout figure 2 page 194.
Right Angle Jack Receptacle
Right Angle Plug Receptacle
Gold Plated
Nickel Plated
142-0801-301
142-0801-306
Gold Plated
Nickel Plated
142-0701-301
142-0701-306
Recommended Land Pattern figure 2 page 194.
Mounting hole layout figure 2 page 194.
Right Angle Jack Receptacle – Surface Mount
Straight Jack Receptacle
Gold Plated
Nickel Plated
“A”
142-0701-201
142-0701-206
.155 (3.94)
142-0701-231
142-0701-236
.110 (2.79)
Gold Plated
Packaging
142-0711-301
Stock
142-0711-302
Tape and Reel 425 pcs/reel
Recommended Land Pattern figure 7 page 194.
Mounting hole layout figure 2 page 194.
Straight Bulkhead Jack Receptacle
Gold Plated
Nickel Plated
“A”
142-0701-501
142-0701-506
.155 (3.94)
142-0701-551
142-0701-556
.110 (2.79)
Mounting hole layout figure 1 and 2 page 194.
56
Gold Plated
Nickel Plated
“A”
“B”
142-0701-421
142-0701-426
.700 (17.78)
.450 (11.43)
142-0701-491
142-0701-496
.065 (1.65)
.755 (19.18)
Mounting hole layout figure 2 page 194.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Right Angle Bulkhead Jack Receptacle
SMA CONNECTORS – 50 OHM
PC Mount
PC Mount
59
End Launch Plug Receptacle – Round Contact
The End Launch connector is attached to the circuit board
by inserting the board edge between the legs and soldering the legs and center conductor to pads on the board. For
optimum high frequency performance, the connector to
circuit board transition must be adjusted for low VSWR. To
compensate for the transition from coax to microstrip, trace
widths “A” and “B” must be adjusted based on circuit board
thickness. When properly adjusted, this technique yields a
low VSWR over a wide bandwidth.
The tabulated dimensions “A”, “B”, “C”, ‘D’, and “E” were
determined experimentally to achieve low VSWR (typically
less than 1.5 up to 18 GHz). The circuit board used connectors for these tests was double-sided FR 4 with 1 oz. copper
on both sides. The copper was left on the bottom of the
board to create a ground plane for the 50 Ohm microstrip
structure. While not all inclusive, these dimensions are given
as reference information for selected SMA End Launch connectors. Further adjustments may be necessary depending
upon the application. All dimensions are in inches.
Gold Plated
Nickel Plated
Board Thickness
“A”
“B”
142-0801-801
142-0801-806
.062 (1.57)
.068 (1.73)
.073 (1.85)
142-0801-821
142-0801-826
.042 (1.07)
.048 (1.22)
.093 (2.36)
End Launch Plug Receptacle – Tab Contact
Part No.
Base Width
Board Thickness
“A”
“B”
“C”
“D”
“E”
142-0701-801/806
.375
.062
.103
.090
.250
.440
.200
142-0701-851/858
.375
.062
.103
.090
.250
.440
.200
142-0701-871/876
.375
.062
.103
.090
.250
.440
.200
142-0711-821/826
.250
.062
.103
.070
.170
.380
.165
142-0711-871/876
.375
.047
.083
.075
.250
.440
.200
142-0711-881/886
.375
.047
.083
.075
.250
.440
.200
142-0701-881/886
.375
.031
.050
.045
.250
.440
.200
Tabulated Dimensions “A”, “B”, “C”, and “D” are symmetrical about the center line.
Gold Plated
Nickel Plated
Board Thickness
“A”
“B”
142-0801-811
142-0801-816
.062 (1.57)
.068 (1.73)
.083 (2.11)
142-0801-831
142-0801-836
.042 (1.07)
.048 (1.22)
.103 (2.62)
End Launch Plug Receptacle – Round Contact
Nickel Plated
Board Thickness
“A”
“B”
142-0711-821
142-0711-826
.062 (1.57)
.068 (1.73)
.042 (1 .07)
142-0711-841
142-0711-846
.042 (1.07)
.048 (1.22)
.062 (1.57)
Coupling proof torque 8 lb-ins maximum without support .083 (2.11) wrench.
58
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Gold Plated
SMA CONNECTORS – 50 OHM
PC Mount
PC Mount
End Launch Jack Receptacle – Round Contact
61
End Launch Bulkhead Jack Receptacle – Round Contact
Gold Plated
Nickel Plated
Board Thickness
“A”
“B”
Figure
142-0701-801
142-0701-806
.062 (1.57)
.068 (1.73)
.073 (1.85)
1
142-0701-831
142-0701-836
.042 (1.07)
.048 (1.22)
.093 (2.36)
1
142-0701-881
142-0701-886
.031 (0.79)
.037 (0.94)
.104 (2.64)
2
142-0711-871
142-0711-876
.047 (1.19)
.053 (1.35)
.088 (2.24)
1
End Launch Jack Receptacle – Tab Contact
Gold Plated
Nickel Plated
Board Thickness
“A”
“B”
“O” Ring
Figure
142-0701-871
142-0701-876
.062 (1.57)
.068 (1.73)
.073 (1.85)
No
1
142-0721-871
142-0721-876
.074 (1.88)
.080 (2.03)
.061 (1.55)
No
1
142-0721-841
142-0721-846
.069 (1.75)
.075 (1.91)
.066 (1.68)
No
1
142-0731-861
142-0731-866
.031 (0.79)
.037 (0.94)
.135 (3.43)
Yes
2
End Launch Bulkhead Jack Receptacle – Round Contact
Nickel Plated
Board Thickness
“A”
“B”
Figure
142-0701-851
142-0701-856
.062 (1.57)
.068 (1.73)
.083 (2.11)
1
142-0701-841
142-0701-846
.042 (1.07)
.048 (1.22)
.103 (2.62)
1
142-0711-881
142-0711-886
.047 (1.19)
.053 (1.35)
.098 (2.24)
1
142-0721-811
142-0721-816
.025 (0.64)
.030 (0.76)
.121 (3.07)
1
142-0721-861
142-0721-866
.032 (0.81)
.037 (0.94)
.083 (2.11)
2
Nickel Plated
Board Thickness
142-0711-811
142-0711-816
.062 (1.57)
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
60
Gold Plated
Gold Plated
SMA CONNECTORS – 50 OHM
Bulkhead Mount
End Launch Jack Receptacle – Surface Mount
Self-Fixture End Launch
Gold Plated, Round Contact
.375
9.52
4X .040
1.02
63
.375
9.52
.187
4.75
.065
1.65
2X .040
1.02
.312
7.92
Gold Plated
Packaging
142-0721-881
Stock
142-0721-882
Tape and Reel 475 pcs/reel
Recommended land pattern figure 22 page 195.
3X
.006
2X .068
1.73
2X .059
1.5
CLOSED END OF SELF
FIXTURE TERMMINALS
.030
0.76
Part No.
Board Thickness
142-0791-801
.062 (1.57)
2X .073
1.85
1/4-36 UNEF-2A
Assembly instructions page 227.
Front Mount Bulkhead Jack Receptacle
Gold Plated, Tab Contact
4X .040
1.02
.375
9.52
.187
4.75
.375
9.52
.065
1.65
2X .040
1.02
.312
7.92
Gold Plated
Nickel Plated
142-0701-411
142-0701-416
3X
2X "A"
2X "C"
CLOSED END OF SELF
FIXTURE TERMINALS
2X "B"
.020
0.51
Mounting hole layout figure 1 page 194.
Rear Mount Bulkhead Jack Receptacle
.006
.010
0.25
“B”
1/4-36 UNEF-2A
Part No.
Board Thickness
“A”
“C”
142-0791-811
.042 (1.07)
.048 (1.22) .103 (2.62)
.039 (0.99)
142-0791-821
.062 (1.57)
.068 (1.73) .083 (2.11)
.059 (1.50)
Assembly instructions page 227.
Gold Plated
Nickel Plated
142-0701-401
142-0701-406
Gold Plated, Round Contact – High Frequency
.187
4.75
.100
2.54
Mounting hole layout figure 1 page 194.
.067
1.70
.285
7.24
Ø
7/32
FLATS
Part No.
142-0701-531
142-0701-536
Frequency Range Board Thickness
.0150
0.38
.003
“B”
.080
2.03
“A”
“B”
142-1701-821 0-26.5 GHz
.062 (1.57)
.068
.059
142-1701-831 0-26.5 GHz
.059 (1.49)
.063
.054
CLOSED END OF SELF
FIXTURE TERMINALS
“A”
1/4-36 UNEF-2A
Assembly instructions page 227.
Mounting hole layout figure 1 page 194.
62
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Ø
Nickel Plated
.247
6.27
.060
1.52
Right Angle Bulkhead Mount Jack Receptacle
Gold Plated
.375
9.52
SMA CONNECTORS – 50 OHM
Spark Plugs
Spark Plugs
Jack Receptacle – Thread Mount Field Replaceable
Gold Plated
Nickel Plated
Accepts Pin Size
142-1731-001
142-1731-006
.020 (0.51)
142-1731-011
142-1731-016
.036 (0.91)
Mounting hole layout figure 19 page 195.
Jack Receptacle – Thread Mount Extended Dielectric (Non-Hermetic)
Gold Plated
Nickel Plated
142-1731-021
142-1731-026
Mounting hole layout for 142-1731-021 figure 19 page 195.
Mounting hole layout for 142-1731-026 figure 18 page 195.
65
Jack Receptacle – Knurl Mount* Tab Contact
Gold Plated
Nickel Plated
142-1721-001
142-1721-006
* Not intended for use in materials harder than Rockwell B82.
Assembly tool 140-0000-954 page 188.
Mounting hole layout figure 17 page 195.
Jack Receptacle – Knurl Mount* Round Contact
Gold Plated
Nickel Plated
142-1721-011
142-1721-016
* Not intended for use in materials harder than Rockwell B82.
Assembly tool 140-0000-954 page 188.
Mounting hole layout figure 17 page 195.
Jack Receptacle – Thread Mount with Hardware Extended Dielectric Bulkhead
Nickel Plated
142-1731-031
142-1731-036
Mounting hole layout for 142-1731-031 figure 18 page 195.
Mounting hole layout for 142-1731-036 figure 1 page 194.
64
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Gold Plated
SMA CONNECTORS – 50 OHM
Spark Plugs
Panel Mount
Jack Receptacle – Knurl Mount* Round Contact
67
2-Hole Flange Mount Jack Receptacle – Flush Dielectric
Gold Plated
Nickel Plated
“A”
“B”
Gold Plated
Nickel Plated
142-1721-011
142-1721-016
.030 (0.76)
.187 (3.18)
142-0701-621
142-0701-626
142-1721-021
142-1721-026
.050 (1.24)
.190 (4.83)
* Not intended for use in materials harder than Rockwell B82.
Mounting hole layout figure 17 page 195.
Jack Receptacle – Knurl Mount* Solder Cup Contact
Gold Plated
Nickel Plated
142-0701-481
142-0701-486
4-Hole Flange Mount Jack Receptacle – Flush Dielectric
Gold Plated
Nickel Plated
142-0701-631
142-0701-636
* Not intended for use in materials harder than Rockwell B82.
Mounting hole layout figure 17 page 195.
Jack Receptacle – Knurl Mount* Extended Dielectric
Nickel Plated
“A”
“B”
142-1721-031
142-1721-036
.190 (4.83)
.095 (2.41)
142-1721-041
142-1721-046
.240 (6.10)
.180 (4.57)
142-1721-051
142-1721-056
.705 (17.91)
.590 (14.99)
* Not intended for use in materials harder than Rockwell B82.
Mounting hole layout figure 17 page 195.
66
Gold Plated
Nickel Plated
“A”
“B”
142-1701-131
142-1701-136
.705 (17.91)
.590 (14.99)
142-1701-031
142-1701-036
.240 (6.10)
.180 (4.57)
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Gold Plated
2-Hole Flange Mount Jack Receptacle – Extended Dielectric
SMA CONNECTORS – 50 OHM
Panel Mount
Panel Mount
4-Hole Flange Mount Jack Receptacle – Extended Dielectric
Gold Plated
Nickel Plated
“A”
“B”
142-1701-121
142-1701-126
.705 (17.91)
.590 (14.99)
142-1701-041
142-1701-046
.190 (4.83)
.095 (2.41)
69
4-Hole Flange Mount Jack Receptacle – Extended Dielectric
Gold Plated
Nickel Plated
142-1701-191
142-1701-196
4-Hole Right Angle Flange Mount Jack Receptacle – Extended Dielectric
4-Hole Flange Mount Jack Receptacle – Extended Dielectric
Gold Plated
Nickel Plated
142-1701-011
142-1701-016
Gold Plated
Nickel Plated
142-0701-701
142-0701-706
4-Hole Right Angle Flange Mount Jack Receptacle – Extended Dielectric
2-Hole Flange Mount Jack Receptacle – Extended Dielectric
Nickel Plated
142-1701-201
142-1701-206
Nickel Plated
142-1711-001
142-1711-006
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
68
Gold Plated
Gold Plated
SMA CONNECTORS – 50 OHM
Panel Mount
Field Replaceable
2-Hole Right Angle Flange Mount Jack Receptacle – Extended Dielectric 90° Orientation
71
Application Notes
The field replaceable style of connector is known by many names in the industry, such as MIC launcher, hermetic seal launcher,
spark plug launcher, etc. Some types, such as those known as “spark plugs,” have the hermetic seal incorporated into the connector. These types require special welding to install and can not be replaced without destroying the hermeticity of the circuit
housing. True field replaceable connectors, such as the Johnson line, are easy to install and replace. Because the hermetic seal is
not incorporated into the connector design, the connector can be removed and replaced without destroying the hermetic seal
or the hermeticity of the circuit housing.
Gold Plated
Nickel Plated
“A”
142-1711-011
142-1711-016
.705 (17.91) .590 (14.99)
“B”
142-1711-061
142-1711-066
.195 (4.95)
.130 (3.30)
All of the above-mentioned connector types perform the same basic function-creating a transition from microstrip circuitry
to a coaxial transmission line. Whenever possible, the hermetic seal pin diameter should be chosen as close as possible to the
microstrip trace width. For optimum electrical performance, the transition from the hermetic seal to the microstrip trace must
be properly compensated which involves adjusting the microstrip trace width to minimize any impedance discontinuities found
in the transition area.
The plot shown below is representative of the typical return loss of a Johnson SMA field replaceable connector. To produce the
data shown below, a test fixture is created using the appropriate Johnson hermetic seal. The fixture consists of a suitably thick
spacer plate with the hermetic seal mounted flush to both surfaces. Two connectors are mounted back to back around the
fixture and the VSWR of this test assembly is measured. The return loss data shown is equivalent to the square root of the measured VSWR of the test assembly. Since the connectors tested are of identical design, it can be stated with fair accuracy that the
data shown represents the response of a single field replaceable connector and its transition to the hermetic seal.
2-Hole Right Angle Flange Mount Jack Receptacle – Extended Dielectric +45° Orientation
Gold Plated
Nickel Plated
142-1711-021
142-1711-026
Although we do not publish a VSWR specification for field replaceable connectors, typical connector VSWR can be expected
to be better than 1.1 + .01f (f = GHz). A VSWR specification is not stated because an industry standardized method for testing
field replaceable connectors does not exist. The actual performance of the connector is dependent upon the application for the
following reasons:
2-Hole Right Angle Flange Mount Jack Receptacle – Extended Dielectric -45° Orientation
2. It is recommended that the hermetic seal be mounted flush with the circuit housing. Tolerance variations between the
hermetic seal and machined housing do not always guarantee an optimum transition to the connector. Emerson does not
recommend the addition of a counter bore in the circuit housing to accommodate solder washers as solder voids will cause
electrical discontinuities.
Gold Plated
Nickel Plated
142-1711-031
142-1711-036
3. As stated above, the transition between the hermetic seal pin and the microstrip trace will affect electrical performance.
Several different methods of hermetic seal mounting and seal pin to microstrip trace attachment are used in the industry.
We cannot recommend one method over the other as this is dependent upon the customer’s application.
“As always, quotes for non-standard field replaceable connectors and/or hermetic seals are welcome.”
70
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
1. The choice of hermetic seal to be used by the customer is not specified by the connector manufacturer. Hermetic seals
produced by different manufacturers will not have the same electrical characteristics. For optimum electrical performance,
we recommend the use of our standard 142-1000-001, 002, 003 and 004 hermetic seals for pin diameters of .012 (.30),
.015 (.38), .018 (0.46) and .020 (0.51). Custom hermetic seal configurations can be quoted.
SMA CONNECTORS – 50 OHM
Field Replaceable Panel Mount
Field Replaceable Panel Mount
2-Hole Flange Mount Jack Receptacle – with EMI Gasket
73
4-Hole Flange Mount Jack Receptacle – without EMI Gasket
Accepts Pin Size
Gold Plated
Nickel Plated
Accepts Pin Size
Gold Plated
Nickel Plated
.012 (0.30)
142-1701-601
142-1701-606
.020 (0.51)
142-1701-531
142-1701-536
.015 (0.38)
142-1701-611
142-1701-616
.036 (0.91)
142-1701-541
142-1701-546
.018 (0.46)
142-1701-621
142-1701-626
4-Hole Flange Mount Jack Receptacle – with EMI Gasket
2-Hole Flange Mount Jack Receptacle – without EMI Gasket
Gold Plated
Nickel Plated
142-1701-551
142-1701-556
Accepts Pin Size
Gold Plated
Nickel Plated
.012 (0.30)
.020 (0.51)
142-1701-631
142-1701-636
.015 (0.38)
142-1701-561
142-1701-566
.036 (0.91)
142-1701-641
142-1701-646
.018 (0.46)
142-1701-571
142-1701-576
4-Hole Flange Mount Jack Receptacle – with EMI Gasket
Accepts Pin Size
Gold Plated
Nickel Plated
.012 (0.30)
142-1701-501
142-1701-506
.015 (0.38)
142-1701-511
142-1701-516
.018 (0.46)
142-1701-521
142-1701-526
4-Hole Flange Mount Jack Receptacle – without EMI Gasket
Accepts Pin Size
Gold Plated
Nickel Plated
.020 (0.51)
142-1701-581
142-1701-586
.036 (0.91)
142-1701-591
142-1701-596
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
72
Accepts Pin Size
SMA CONNECTORS – 50 OHM
Field Replaceable Panel Mount
4-Hole Right Angle Flange Mount Jack Receptacle – with EMI Gasket
Accepts Pin Size
Gold Plated
Nickel Plated
.015 (0.38)
142-1711-511
142-1711-516
.018 (0.46)
142-1711-521
142-1711-526
75
Hermetic Seal Feedthrough
Part No.
2-Hole Flange Mount Plug Receptacle – with EMI Gasket
Field Replaceable
Item 1
Outer Ring
142-1000-001
Kovar
Gold pl .00005
min over
Nickel pl .000005 min
Item 2
Insulator
Item 3
“A”
or equivalent
Nickel pl .000005 min
“B”
“C”
“D”
“E”
Pin
.0625 .180
.0985 .012
Glass
Kovar
.070
(1.59)
(2.50)
Corning
7052
Gold
pl .00005
min
over
(1.78)
(4.57)
(0.30)
Kovar
.072.0625
.180 .0985
.015
142-1000-002 Kovar Glass
min over
Gold
pl .00005
(1.83) (1.59) (4.57) (2.50) (0.38)
Gold pl .00005min
over Corning
7070
Nickel pl
.000005 min
or
equivalent
Nickel pl .000005 mm
Kovar
.072
.0600 .180
.1100 .018
142-1000-003 Kovar Glass
Gold pl .00005
Corning
7050
Gold pl .00005 min over
(1.83) (1.52) (4.57) (2.79) (0.46)
min over
Nickel
p1 .000005
Nickel pl
.000005
min
equivalent
or
min
142-1000-004
Accepts Pin Size
Gold Plated
Nickel Plated
.012 (0.30)
142-1801-601
142-1801-606
.015 (0.38)
142-1801-611
142-1801-616
.018 (0.46)
142-1801-621
142-1801-626
Part No.
142-1000-002
142-1000-003
142-1000-004
Nickel Plated
.012 (0.30)
142-1801-551
142-1801-556
.015 (0.38)
142-1801-561
142-1801-566
.018 (0.46)
142-1801-571
142-1801-576
.015 (0.38)
.063 (1.60)
.102 (2.59)
.018
(0.46)
.060
(1.52)
.114
(2.90)
.020
(0.51)
.060
(1.52)
.162
(4.11)
1. The hermetic seal should
be mounted as
.020
(0.51)
Air “H”
Teflon* “H”
.028
(0.71)
(0.99)
.039
.035 (0.89)
.049 (1.24)
.042 (1.07)
.059 (1.50)
.046 (1.17)
.065
(1.65)
Electrical
flush as possible with the housing. Excessive
50
Ohms
recession will create
a high impedance
air
gap Impedance:
26.5 GHz
Frequency
Range:
DC
to
which degrades electrical performance.
VSWR:
Dependent
upon application
2. The use of an additional counterbore to
accommodate a solder ring for seal mounting
Working Voltage:
250 VRMS max at sea level
is not recommended. A slight chamfer may be
Dielectric Withstanding Voltage: 500 VRMS min at sea level
with
usedif care is taken
to completely
fill the area
Insulation Resistance:
5000 Megohm min
solder—avoid air gaps.
Insertion Loss:
.015F dB max (F in GHz)
3. Dimensions shown are given to achieve 50 Ohms
with either air or a teflon insulator. A teflon insulator
Environmental
may be helpful insupporting small pin diameters.
Hermeticity:
Solderability:
Operating Temperature:
74
.070
.0600 .203
.1580
(1.78) (1.52) (5.16) (4.01)
1x10-8 cc/sec at
one atmosphere
MIL-STD-202,
Method 209
-55O C to +165O C
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Gold Plated
Pin Diameter
“F”
“G”
.012 (0.30)
.063 (1.60)
(2.59)
.102
* Teflon is a registered trademark of DuPont
Notes:
Accepts Pin Size
Glass
Kovar
Corning 7052 Gold pl .00005 min over
or equivalent
Nickel
pl .000005
min
Mounting Hole Dimensions
142-1000-001
4-Hole Flange Mount Plug Receptacle – with EMI Gasket
Kovar
Gold pl .00005min over
Nickel pl .000005 min
SMA CONNECTORS – 50 OHM
In-Series Adapters
In-Series Adapters
Jack to Jack Adapter
Gold Plated
Nickel Plated
142-0901-801
142-0901-806
Jack to Bulkhead Jack Adapter
Right Angle Jack to Jack Adapter
Gold Plated
142-0901-921
Right Angle Plug to Plug Adapter
Gold Plated
Nickel Plated
Gold Plated
142-0901-401
142-0901-406
142-0901-931
Plug to Plug Adapter
77
Right Angle Jack to Plug Adapter
Gold Plated
Gold Plated
Nickel Plated
142-0901-811
142-0901-816
142-0901-941
Plug to Jack Adapter
76
Gold Plated
Nickel Plated
142-0901-821
142-0901-826
Gold Plated
Nickel Plated
Resistance
142-0801-861
142-0801-866
50 Ohm
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – 50 OHM
Dummy Load Plug
SMA CONNECTORS – REVERSE POLARITY– 50 OHM
Specifications
Specifications
Environmental Specifications
Electrical Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range: - 65°C to + 165°C
Thermal Shock:
MIL-STD-202, Method 107, Condition B
Corrosion:
MIL-STD-202, Method 101, Condition B
Shock:
MIL-STD-202, Method 213, Condition I
Vibration:
MIL-STD-202, Method 204, Condition D
Moisture Resistance: MIL-STD-202, Method 106
Material Specifications
Bodies:
Contacts:
Nut Retention Spring:
Insulators:
Expansion Caps:
Crimp Sleeves:
Mounting Hardware:
Brass per ASTM B16, gold plated* per MIL-DTL-45204 .00001” min or nickel plated per ASTM B16
Male - brass per QQ-B-626, gold plated per MIL-DTL-45204 .00003” min
Female - beryllium copper per ASTM B196, gold plated* per MIL-DTL-45204 .00003” min
Beryllium copper per ASTM B196, unplated
PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457 or Tefzel per ASTM D 3159
Brass per ASTM B16, gold plated* per MIL-DTL-45204 .00001” min. or nickel plated per SAE-AMS2423
Copper per ASTM B301 or brass per ASTM B16, gold plated* per MIL-DTL-45204 .00001” min or nickel plated
per SAE-AMS2423
Brass (nuts) per ASTM B16 or phosphor bronze (lockwashers) per ASTM B139, gold plated*
per MIL-DTL-45204 .00001” min
* All gold plated parts include a .00005” min nickel barrier layer.
† Avoid user injury due to misapplication. See safety advisory definitions.
Mating Engagement for SMA Reverse Polarity Series
† Avoid user injury due to misapplication. See safety advisory definitions.
Mechanical Ratings
78
Torque (oz-in)
N/A
N/A
N/A
N/A
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – REVERSE POLARITY– 50 OHM
Impedance: 50 Ohms
Frequency Range:
Flexible cable connectors...............................................................................................................................0-12.4 GHz
Flexible cable connectors...............................................................................................................................0-18.0 GHz
VSWR : (max) (f = GHz)
Straight
Right Angle
Cabled Connectors Cabled Connectors
RG-316, LMR-100 cable...............................................................................................1.15 + .02f
1.15 + .03f
RG-58, LMR-195 cable.................................................................................................1.17 + .025f
1.17 + .06f
RG-142 cable...............................................................................................................1.17 + .02f
1.15 + .03f
LMR-200, LMR-240 cable.............................................................................................1.10 + .03f
1.10 + .06f
Uncabled receptacles......................................................................................................................................N/A
Working Voltage: (VRMS max)
Sea Level
70K Feet
RG-316, LMR-100, 195, 200....................................................................................... 250 65
RG-58, RG-142, LMR-240, uncabled receptacles........................................................ 335 85
Dielectric Withstanding Voltage: (VRMS min at sea level)
RG-316; LMR-100, 195, 200 ......................................................................................................................... 750
RG-58, RG-142, LMR-240, uncabled receptacles............................................................................................ 1000
Insulation Resistance: 5000 megohms min
Contact Resistance: (milliohms max)
Initial
After Environmental
Center contact (straight cabled connectors and uncabled receptacles).................... 3.0 4.0
Center contact (right angle cabled connectors)......................................................... 4.0 6.0
Outer contact (all connectors).................................................................................... 2.0
N/A
Braid to body (gold plated connectors)...................................................................... 0.5
N/A
Braid to body (nickel plated connectors).................................................................... 5.0
N/A
Corona Level: (Volts min at 70,000 feet)
RG-316, LMR-100, 195, 200...........................................................................................................................190
RG-58, RG-142, LMR-240, uncabled receptacles ...........................................................................................250
Insertion Loss: (dB max)
Straight flexible cable connectors.........................................................................................0.06 f (GHz), tested at 6 GHz
Right angle flexible cable connectors....................................................................................0.15 f (GHz), tested at 6 GHz
Low loss flexible straight cable connectors............................................................................0.06 f (GHz), tested at 1 GHz
Low loss flexible right angle cable connectors.......................................................................0.15 f (GHz), tested at 1 GHz
Uncabled receptacles, field replaceable.........................................................................................................N/A
RF Leakage: (dB min, tested at 2.5 GHz)
Flexible cable connectors............................................................................................................................... -60 dB
Uncabled receptacles and adapters ............................................................................................................... N/A
RF High Potential Withstanding Voltage:
(VRMS min tested at 4 and 7 MHz)† RG-316; LMR-100, 195, 200................................................................... 500
RG-58, RG-142, LMR-240, uncabled receptacles............................................................................................. 670
Engagement Design:
Reverse Polarity, Series SMA
Engagement/Disengagement Force: 2 lb-in max max
Mating Torque:
7 to 10 lb-in
Bulkhead Mounting Nut Torque:
15 lb-in
Coupling Proof Torque:
15 lb-in min
Coupling Nut Retention:
60 lbs min
Contact Retention:
6 lbs min axial force (captivated contacts)
4 oz-in min 4 oz-in min
Cable Retention:
Axial Force* (lbs)
Connectors for RG-316, LMR-100.............................................................................. 20
Connectors for LMR195, 200..................................................................................... 30
Connectors for RG-58, LMR-240................................................................................ 40
Connectors for RG-142.............................................................................................. 45
*Or cable breaking strength whichever is less.
Durability: 500 cycles minimum
79
SMA CONNECTORS – REVERSE POLARITY– 50 OHM
Flexible Cable
PC Mount
Straight Jack Receptacle
Straight Crimp Type Plug – Solder or Crimp Captivated Contact
Cable Type
Gold Plated
Nickel Plated
“A”
RG-316/U, 188, 174, 161, LMR-100 HPF-100, RF-100
142-4403-001
142-4403-006
.706 (17.93)
RG-316 DS, 188 DS
142-4404-001
142-4404-006
.706 (17.93)
RG-58, 141, 303 LMR-195, HPF-195,RF-195
142-4407-001
142-4407-006
.706 (17.93)
RG-142, 55, 223, 400
142-4408-001
142-4408-006
.706 (17.93)
LMR-200, HPF-200, RF-200
142-4439-001
142-4439-006
.844 (21.44)
LMR-240, HPF-240, RF-240
142-4435-001
142-4435-006
.844 (21.44)
81
Gold Plated
Nickel Plated
142-4701-201
142-4701-206
Mounting hole layout figure 2 page 194.
Assembly Instructions: LMR 195, 200 and 240 page 219. All other cables page 220.
Right Angle Bulkhead Jack Receptacle
Right Angle Crimp Type Plug – Captivated Contact
Gold Plated
Nickel Plated
142-4701-501
142-4701-506
Mounting hole layout figure 1 and 2 page 194.
Gold Plated
Nickel Plated
“A”
“B”
RG-316, 188, 174, 161, LMR-100, HPF-100, RF-100
142-4403-101
142-4403-106
.611 (15.52)
.470 (11.94)
RG-316 DS, 188 DS
142-4404-101
142-4404-106
.611 (15.52)
.470 (11.94)
RG-58, 141, 303, LMR-195, HPF-195, RF-195
142-4407-101
142-4407-106
.611 (15.52)
.470 (11.94)
RG-142, 55, 223, 400
142-4408-101
142-4408-106
.611 (15.52)
.470 (11.94)
LMR-200, HPF-200, RF-200
142-4439-101
142-4439-106
.611 (15.52)
.470 (11.94)
LMR-240, HPF-240, RF-240
142-4435-101
142-4435-106
.635 (16.13)
.490 (12.45)
End Launch Bulkhead Jack Receptacle
Assembly Instructions: LMR 195, 200 and 240 page 224. All other cables page 229.
Center conductor of cable serves as contact.
Straight Crimp Type Bulkhead Jack – Captivated Contact
Cable Type
Gold Plated
Nickel Plated
RG-316, 188, 174, 161
142-4303-401
142-4303-406
RG-316 DS, 188 DS
142-4304-401
142-4304-406
RG-58, 141, 303
142-4307-401
142-4307-406
RG-142, 55, 223, 400
142-4308-401
142-4308-406
Assembly instructions page 219.
Mounting hole layout figure 1 page 194.
80
Gold Plated
Nickel Plated
Board Thickness
142-4701-801
142-4701-806
.062 (1.57)
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – REVERSE POLARITY– 50 OHM
Cable Type
SMA CONNECTORS – REVERSE THREAD– 50 OHM
Specifications
Specifications
Environmental Specifications
Electrical Specifications
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
Temperature Range: - 65°C to + 165°C
Thermal Shock:
MIL-STD-202, Method 107, Condition B
Corrosion:
MIL-STD-202, Method 101, Condition B
Shock:
MIL-STD-202, Method 213, Condition I
Vibration:
MIL-STD-202, Method 204, Condition D
Moisture Resistance: MIL-STD-202, Method 106
Material Specifications
Bodies:
Contacts:
Nut Retention Spring:
Insulators:
Expansion Caps:
Crimp Sleeves:
Mounting Nut:
Brass per ASTM B16, gold plated* per MIL-DTL-45204 .00001” min or nickel plated per ASTM B16
Male - brass per QQ-B-626, gold plated* per MIL-DTL-45204 .00003” min
Female - beryllium copper per ASTM B196, gold plated* per MIL-DTL-45204 .00003” min
Beryllium copper per ASTM B196. Unplated
PTFE fluorocarbon per ASTM D1710 and ASTM D1457 or Tefzel per ASTM D 3159
Brass per ASTM B16, gold plated per MIL-DTL-45204 .00001” min or nickel plated* per SAE-AMS2423
Copper per ASTM B301 or brass per ASTM B301, gold plated* per MIL-DTL-45204 .00001” min or nickel
plated per SAE-AMS2423
Brass per ASTM B16, green chromate over zinc plated Mounting Lockwasher: Phosphor bronze per
ASTM B139, gold plated* per MIL-DTL-45204 .00001” min or nickel plated per SAE-AMS2423
* All gold plated parts include a .00005” min nickel barrier layer.
† Avoid user injury due to misapplication. See safety advisory definitions.
Mating Engagement for SMA Reverse Thread Series
† Avoid user injury due to misapplication. See safety advisory definitions.
Mechanical Ratings
82
Torque (oz-in)
N/A
N/A
N/A
N/A
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – REVERSE THREAD– 50 OHM
Impedance: 50 Ohms
Frequency Range:
Flexible cable connectors.................................................................................................................................0-12.4 GHz
Uncabled receptacles.......................................................................................................................................0-18.0 GHz
VSWR: (max) (f = GHz)
Straight
Right Angle
Cabled Connectors
Cabled Connectors
RG-316, LMR-100 cable..................................................................................... 1.15 + .02f
1.15 + .03f
RG-58, LMR-195 cable....................................................................................... 1.15 + .01f
1.15 + .02f
RG-142 cable..................................................................................................... 1.15 + .01f
1.15 + .02f
LMR-200, LMR-240 cable................................................................................... 1.10 + .03f
1.10 + .06f
Uncabled receptacles........................................................................................................................................ N/A
Working Voltage: (VRMS max)
Sea Level
70K Feet
RG-316; LMR-100, 195, 200............................................................................... 250 65
RG-58, RG-142, LMR-240, uncabled receptacles................................................ 335 85
Dielectric Withstanding Voltage: (VRMS min at sea level)
RG-316; LMR-100, 195, 200 ........................................................................................................................... 750
RG-58, RG-142, LMR-240, uncabled receptacles.............................................................................................. 1000
Insulation Resistance: 5000 megohms min
Contact Resistance: (milliohms max)
Initial
After Environmental
Center contact (straight cabled connectors and uncabled receptacles)............3.0 4.0
Center contact (right angle cabled connectors).................................................4.0 6.0
Outer contact (all connectors)............................................................................2.0
N/A
Braid to body (gold plated connectors)..............................................................0.5
N/A
Braid to body (nickel plated connectors)............................................................5.0
N/A
Corona Level: (Volts min at 70,000 feet)†
RG-316, LMR-100, 195, 200............................................................................................................................190
RG-58, RG-142, LMR-240, uncabled receptacles ............................................................................................250
Insertion Loss: (dB max)
Straight flexible cable connectors..........................................................................................0.06 f (GHz), tested at 6 GHz
Right angle flexible cable connectors.....................................................................................0.15 f (GHz), tested at 6 GHz
Low loss flexible straight cable connectors.............................................................................0.06 f (GHz), tested at 1 GHz
Low loss flexible right angle cable connectors........................................................................0.15 f (GHz), tested at 1 GHz
Uncabled receptacles, field replaceable...........................................................................................................N/A
RF Leakage: (dB min tested at 2.5 GHz)
Engagement Design:
Reverse Thread, Series SMA
Engagement/Disengagement Force: 2 lb-in max
Mating Torque:
7 to 10 lb-in
Bulkhead Mounting Nut Torque:
15 lb-in
Coupling Proof Torque:
15 lb-in min
Coupling Nut Retention:
60 lbs min
Contact Retention:
6 lbs. min axial force (captivated contacts)
4 oz-in min torque (uncabled receptacles)
Cable Retention:
Axial Force* (lbs)
RG-316, LMR-100................................................................................................ 20
LMR195, 200....................................................................................................... 30
RG-58, LMR-240.................................................................................................. 40
RG-142................................................................................................................ 45
*Or cable breaking strength whichever is less.
Durability: 500 cycles min
83
SMA CONNECTORS – REVERSE THREAD– 50 OHM
Flexible Cable
PC Mount
85
Straight Jack Receptacle
Straight Crimp Type Plug – Solder or Crimp Captivated Contact
Cable Type
Gold Plated
Nickel Plated
“A”
Gold Plated
Nickel Plated
RG-316, 188, 174, 161, LMR-100 HPF-100 RF-100
142-5403-001
142-5403-006
.706 (17.93)
142-5701-201
142-5701-206
RG-316 DS, 188 DS,
142-5404-001
142-5404-006
.706 (17.93)
Mounting hole layout figure 2 page 194.
RG-58, 141, 303 LMR-195, HPF-195, RF-195
142-5407-001
142-5407-006
.706 (17.93)
RG-142, 55, 223, 400
142-5408-001
142-5408-006
.706 (17.93)
LMR-200, HPF-200, RF-200
142-5439-001
142-5439-006
.844 (21.44)
LMR-240, HPF-240, RF-240
142-5435-001
142-5435-006
.844 (21.44)
Right Angle Bulkhead Jack Receptacle
Assembly Instructions: LMR 195, 200 and 240 page 220. All other cables page 219.
Right Angle Crimp Type Plug – Captivated Contact
Gold Plated
Nickel Plated
142-5701-501
142-5701-506
Mounting hole layout figures 1 and 2 page 194.
End Launch Bulkhead – Round Contact
Gold Plated
Nickel Plated
“A”
“B”
RG-316, 188, 174, 161, LMR-100 HPF-100 RF-100
142-5403-101
142-5403-106
.611 (15.52)
.470 (11.94)
RG-316 DS 188 DS
142-5404-101
142-5404-106
.611 (15.52)
.470 (11.94)
RG-58, 141, 303, LMR-195 HPF-195 RF195
142-5407-101
142-5407-106
.611 (15.52)
.470 (11.94)
RG-142, 55, 223, 400
142-5408-101
142-5408-106
.611 (15.52)
.470 (11.94)
LMR-200 HPF-200 RF-200
142-5439-101
142-5439-106
.611 (15.52)
.470 (11.94)
LMR-240 HPF-240 RF-240
142-5435-101
142-5435-106
.635 (16.13)
.490 (12.45)
Assembly instructions: LMR 195, 200 and 240 page 229. All other cables page 224.
Straight Crimp Type Bulkhead Jack – Solder or Crimp
84
Cable Type
Gold Plated
Nickel Plated
RG-316, 188, 174, 161
142-5303-401
142-5303-406
RG-316 DS, 188 DS
142-5304-401
142-5304-406
RG-58, 141, 303
142-5307-401
142-5307-406
RG-142, 55, 223, 400
142-5308-401
142-5308-406
Assembly instructions page 219.
Mounting hole layout figure 1 page 194.
Gold Plated
Nickel Plated
Board Thickness
142-5701-801
142-5701-806
.062 (1.57)
End Launch Bulkhead Jack Receptacle – Round Contact
Gold Plated
Nickel Plated
Board Thickness
142-5701-811
142-5701-816
.062 (1.57)
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – REVERSE THREAD – 50 OHM
Cable Type
SMA CONNECTORS – NON-MAGNETIC – 50 OHM
Flexible Cable
Specifications
Straight Crimp Type Plug (3-piece) – Captivated Contact
Electrical Specifications
Impedance: 50 Ohms
Frequency Range: Flexible cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-12.4 GHz
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-18.0 GHz
VSWR: (max) (f = GHz)
Straight
Right Angle
Cabled Connectors Cabled Connectors
RG-316 cable.......................................................................................................... 1.15 + .02f
1.15 + .03f
RG-58 cable ........................................................................................................... 1.15 + .01f
1.15 + .02f
Uncabled receptacles.................................................................................................................................. N/A
Working Voltage: (VRMS max)†
Sea Level
70K Feet
RG-316.................................................................................................................... 250 65
RG-58, uncabled receptacles................................................................................... 335 85
Dielectric Withstanding Voltage: (VRMS min at sea level)†
RG-316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750
RG-58, uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
Insulation Resistance: 5000 megohms min
Contact Resistance: (milliohms max )
After
Initial
Environmental
Center contact (straight cabled connectors, uncabled receptacles)..........................3.0 4.0
Center contact (right angle cabled connectors)........................................................4.0 6.0
Outer contact (all connectors)..................................................................................2.0
N/A
Braid to body ...........................................................................................................0.5
N/A
Corona Level: (Volts min at 70,000 feet)†
RG-316
190
RG-58, uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Insertion Loss: (dB max)
Straight flexible cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.06 f (GHz), tested at 6 GHz
Right angle flexible cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 f (GHz), tested at 6 GHz
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
RF Leakage: (dB min tested at 2.5 GHz)
Flexible cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -60 dB
Uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
RF High Potential Withstanding Voltage: (VRMS minimum, tested at 4 and 7 MHz)†
RG-316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
RG-58, uncabled receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670
† Avoid user injury due to misapplication. See safety advisory definitions inside front cover.
Cable Type
Gold Plated
RG-316, 188, 174
142-9403-011
RG-316 DS, 188 DS
142-9404-011
RG-58, 141, 303
142-9407-001
Assembly instructions page 219.
Right Angle Crimp Type Plug – Captivated Contact
Cable Type
Gold Plated
RG-316, 188, 174
142-9403-101
RG-316 DS, 188 DS
142-9404-101
RG-58, 141
142-9407-101
Assembly instructions page 224.
Environmental Specifications
Temperature Range:
Thermal Shock:
Corrosion:
Shock:
Vibration:
Moisture Resistance:
Straight Crimp Type Bulkhead Jack (3-piece) – Captivated Contact
Torque (oz-in)
N/A
N/A
Cable Type
Gold Plated
RG-316, 188, 174
142-9303-411
Assembly instructions page 219.
(Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012)
- 65°C to + 165°C
MIL-STD-202, Method 107, Condition B
MIL-STD-202, Method 101, Condition B
MIL-STD-202, Method 213, Condition I
MIL-STD-202, Method 204, Condition D
MIL-STD-202, Method 106
Material Specifications
(See non-magnetic materials page 10)
86
† Avoid user injury due to misapplication. See safety advisory definitions inside front cover.
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – NON-MAGNETIC – 50 OHM
Mechanical Specifications
Engagement Design:
MIL-STD-348, Series SMA
Engagement/Disengagement Force: 2 lb-in min max
Mating Torque:
7 to 10 lb-in min
Coupling Proof Torque:
15 lb-in min
Coupling Nut Retention:
60 lbs min
Contact Retention:
6 lbs min axial force (captivated contacts)
4 oz-in min torque (uncabled receptacles)
Cable Retention:
Axial Force* (lbs)
RG-316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RG-58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
*Or cable breaking strength whichever is less.
Durability: 500 cycles min
87
SMA CONNECTORS – NON-MAGNETIC – 50 OHM
PC Mount
PC Mount
Straight Jack Receptacle
89
End Launch Jack Receptacle – Round Contact
Gold Plated
“A”
142-9701-201
.155 (3.94)
Gold Plated
Board Thickness
142-9701-211
.110 (2.79)
142-9701-801
.062 (1.57)
Mounting hole layout figure 3 on page 194.
Straight Plug Receptacle
End Launch Jack Receptacle – Tab Contact
Gold Plated
142-9801-201
Mounting hole layout figure 3 on page 194.
Gold Plated
Board Thickness
142-9701-811
.062 (1.57)
Gold Plated
142-9701-301
Mounting hole layout figure 3 on page 194.
88
For more information, please contact customer service at (507) 833-8822 or (800) 247-8256 • www.EmersonConnectivity.com
Illustrations are shown in inches (millimeters).
SMA CONNECTORS – NON-MAGNETIC – 50 OHM
Right Angle Jack Receptacle
Applications & Design Features
Electrical Specifications
High Frequency SMA End Launch Connectors for Microwave PC Board Substrates
Impedance:
50 Ohms
Frequency Range:
0-26.5 GHz
VSWR: (max) 1.05+.02f(GHz) max at 0-18 GHz,
